检索结果-南通市图书馆

Analysis and Optimization of Operational and Pollutant Attributes of Diesel Engine with CNT-Infused Orange Peel Biodiesel-Diesel Blend Fuel

引用

Journal of Thermal Science 2024年第2期33卷 761-778页

作者： Ranjeet RAI R.R.SAHOO mechanical Engineering department GLA UniversityMathura281406India mechanical Engineering department IIT(BHU)Varanasi221005India

The current study is performed to find sustainable solutions for the future of transportation and environmental *** conventional methods and experimental design table(L16 Orthogonal Array)techniques have been employed to examine and optimize a diesel-powered engine's operational and pollutant *** L16 Orthogonal Array is obtained through Taguchi's experimental design approach using Minitab 16 *** experimental design incorporated three control variables,namely engine speed,fuel type,and engine load,each with four *** operational parameters,namely brake thermal efficiency(BTE)and brake specific fuel consumption(BSFC),as well as the emission characteristics,including hydrocarbon(HC),carbon monoxide(CO),nitrogen oxide(NO),and smoke emissions,were acquired using the L16 orthogonal array(OA) and subsequently *** utilization of methodologies such as signal-to-noise(S/N) ratio and grey analysis was employed to determine the optimal operational state of the engine to achieve maximum performance while minimizing *** engine's ideal state of operation,in terms of BTE and BSFC,was determined to be at 75% engine load,1000 r/min engine speed,and using 10^(-4)(in vol) carbon nanotube incorporated 20% orange peel biodiesel(OPB20CNT100) blended fuel(A3-B1-C4).The study indicated that engine load significantly influenced BTE and BSFC,with 84.05% and 87.79% contribution factors,*** 25% engine load,1000 r/min,and OPB20CNT100 fuel(A1-B1-C4) CO,smoke,NO,and HC emissions were the *** load affects emissions the *** BSFC increased 3.10% and NO emissions 1.77%.BTE,CO,smoke,and HC emissions decreased by 1.9%,12.29%,47.05%,and 47.22%,respectively,at optimal operating conditions concerning diesel *** study shows that Taguchi-Grey's experimental design optimizes diesel engine operational and pollutant *** outcomes revealed that orange peel biodiesel infused with CNT can replace diesel fuel in a

关键词： Taguchi-Grey method OPB20CNT100 transesterification S/N ratio GRG HC CO and NO

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Free vibration and buckling analysis of polymeric composite beams reinforced by functionally graded bamboo fbers

引用

Applied Mathematics and Mechanics(English Edition) 2024年第3期45卷 543-562页

作者： H.M.FEIZABAD M.H.YAS department of mechanical Engineering Razi UniversityKermanshah ***Iran

Natural fibers have been extensively researched as reinforcement materials in polymers on account of their environmental and economic advantages in comparison with synthetic fibers in the recent *** fibers are renowned for their good mechanical properties,abundance,and short cycle *** beams are one of the fundamental structural components and are susceptible to mechanical loads in engineering applications,this paper performs a study on the free vibration and buckling responses of bamboo fiber reinforced composite(BFRC)beams on the elastic *** different functionally graded(FG)layouts and a uniform one are the considered distributions for unidirectional long bamboo fibers across the *** elastic properties of the composite are determined with the law of *** Hamilton’s principle,the governing equations of motion are *** generalized differential quadrature method(GDQM)is then applied to the equations to obtain the *** achieved outcomes exhibit that the natural frequency and buckling load values vary as the fiber volume fractions and distributions,elastic foundation stiffness values,and boundary conditions(BCs)and slenderness ratio of the beam ***,a comparative study is conducted between the derived analysis outcomes for BFRC and homogenous polymer beams to examine the effectiveness of bamboo fibers as reinforcement materials,demonstrating the significant enhancements in both vibration and buckling responses,with the exception of natural frequencies for cantilever beams on the Pasternak foundation with the FG-◇fiber ***,the obtained analysis results of BFRC beams are also compared with those for carbon nanotube reinforced composite(CNTRC)beams found in the literature,indicating that the buckling loads and natural frequencies of BFRC beams are lower than those of CNTRC beams.

关键词： bamboo fiber free vibration buckling analysis functionally graded(FG)beam elastic foundation generalized differential quadrature method(GDQM)

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Dynamic and electrical responses of a curved sandwich beam with glass reinforced laminate layers and a pliable core in the presence of a piezoelectric layer under low-velocity impact

引用

Applied Mathematics and Mechanics(English Edition) 2024年第1期45卷 155-178页

作者： N.SHAHVEISI S.FELI department of mechanical Engineering Razi UniversityKermanshah ***Iran

The dynamic responses and generated voltage in a curved sandwich beam with glass reinforced laminate(GRL)layers and a pliable core in the presence of a piezoelectric layer under low-velocity impact(LVI)are *** current study aims to carry out a dynamic analysis on the sandwich beam when the impactor hits the top face sheet with an initial *** the layer analysis,the high-order shear deformation theory(HSDT)and Frostig's second model for the displacement fields of the core layer are *** classical non-adhesive elastic contact theory and Hunter's principle are used to calculate the dynamic responses in terms of *** order to validate the analytical method,the outcomes of the current investigation are compared with those gained by the experimental tests carried out by other researchers for a rectangular composite plate subject to the *** element(FE)simulations are conducted by means of the ABAQUS *** effects of the parameters such as foam modulus,layer material,fiber angle,impactor mass,and its velocity on the generated voltage are reviewed.

关键词： analytical model piezoelectric layer curved sandwich beam glass reinforced laminate(GRL) pliable core low-velocity impact(LVI) classical non-adhesive elastic contact theory

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Research progress in friction stir processing of magnesium alloys and their metal matrix surface composites: Evolution in the 21^(st )century

引用

Journal of Magnesium and Alloys 2024年第6期12卷 2091-2146页

作者： Roshan Vijay Marode Tamiru Alemu Lemma Nabihah Sallih Srinivasa Rao Pedapati Mokhtar Awang Adeel Hassan department of mechanical Engineering Universiti Teknologi PETRONASBandarSeri IskandarPerak 32610Malaysia department of mechanical Engineering College of EngineeringThe University of Texas Permian BasinMidland-OdessaUnited States mechanical Engineering department Universiti Teknologi BruneiBrunei

Rising concerns about climate change drive the demand for lightweight ***(Mg)alloys are highly valued for their low weight,making them increasingly important in various *** focusing on enhancing the characteristics of Mg alloys and developing their Metal Matrix Composites(MMCs)have gained significant attention worldwide over the past decade,driven by the global shift towards lightweight *** Stir Processing(FSP)has emerged as a promising technique to enhance the properties of Mg alloys and produce ***,FSP adapted to refine grain size from the micro to the nano level and accelerated the development of MMCs due to its solid-state nature and the synergistic effects of microstructure refinement and reinforcement,improving strength,hardness,ductility,wear resistance,corrosion resistance,and fatigue ***,producing defect-free and sound FSPed Mg and Mg-MMCs requires addressing several variables and their interdependencies,which opens up a broad range of practical *** existing reviews on individual FSP of Mg,its alloys,and MMCs,an attempt has been made to analyze the latest research on these three aspects collectively to enhance the understanding,application,and effectiveness of FSP for Mg and its *** review article discusses the literature,classifies the importance of Mg alloys,provides a historical background,and explores developments and potential applications of FSPed Mg *** focuses on novel fabrication methods,reinforcement strategies,machine and tool design parameters,material characterization,and integration with other methods for enhanced *** influence of process parameters and the emergence of defects are examined,along with specific applications in mono and hybrid composites and their microstructure *** study identifies promising reinforcement materials and highlights research gaps in FSP for Mg alloys and MMCs *** conclude

关键词： Magnesium alloys Friction stir processing Metal matrix composites Lightweight Surface modification

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Impact of Fin Arrangement on Heat Transfer and Melting Characteristics of Phase Change Material

引用

Journal of Thermal Science 2024年第2期33卷 435-456页

作者： Arun UNIYAL Yogesh K.PRAJAPATI department of mechanical Engineering National Institute of Technology UttarakhandSrinagar(Garhwal)246174India department of mechanical Engineering BIT SindriDhanbadJharkhand828123India

Present work investigates the heat transfer and melting behaviour of phase change material(PCM) in six enclosures(enclosure-1 to 6) filled with paraffin *** enclosures are equipped with distinct arrangements of the fins while keeping the fin's surface area equal in each *** analysis has been presented to recognize the suitable fin arrangements that facilitate improved heat transfer and melting rate of the *** wall of the enclosure is maintained isothermal for the temperature values 335 K,350 K and 365 *** length of the enclosure including fins is ranging between 0 and *** have been illustrated through the estimation of important performance parameters such as energy absorbing capacity,melting rate,enhancement ratio,and Nusselt *** has been found that melting time(to melt 100% of the PCM) is 60.5%less in enclosure-2(with two fins of equal length) as compared to the enclosure-1,having no *** the fin surface area equal,if the longer fin is placed below the shorter fin(enclosure-3),melting time is further decreased by 14.1% as compared to ***,among all the configurations,enclosure-6 with wire-mesh fin structure exhibits minimum melting time which is 68.4% less as compared to the *** on the findings,it may be concluded that fins are the main driving agent in the enclosure to transfer the heat from heated wall to the *** design and positioning of the fins improve the heat transfer rate followed by melting of the PCM in the entire area of the *** of the favourable vortices and natural convection current in the enclosure accelerate the melting phenomenon and help to reduce charging time.

关键词： phase change material enclosure fin melting fraction energy storage heat transfer

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Heat and mass transfer of a circular porous moist object located in a triangular shaped vented cavity

引用

Journal of Central South University 2024年第6期31卷 1956-1972页

作者： SELIMEFENDIGIL Fatih OZCAN COBAN Seda OZTOP Hakan F department of mechanical Engineering College of EngineeringKing Faisal UniversityAl Ahsa 31982Saudi Arabia department of mechanical Engineering Manisa Celal Bayar UniversityManisa 45140Turkey department of mechanical Engineering Technology FacultyFırat UniversityElazığTurkey

Heat and mass transfer of a circular-shaped porous moist object inside a two-dimensional triangle cavity is investigated by using finite element *** porous object is considered to be a moist food sample,located in the middle of the cavity with inlet and outlet ports with different configurations of inlet/outlet *** drying performance is numerically assessed for different values of Reynolds numbers(between 50 and 250),dry air inlet temperature(between 40 and 80℃)and different locations of the *** is observed that changing the port locations has significant impacts on the flow recirculaitons inside the triangular chamber while convective drying performance is highly *** moisture content reduces with longer time and for higher Reynolds number(Re)*** P4 where inlet and outlet ports are in the middle of the walls provides the most effective configuration in terms of convective drying performance while the worst case is seen for P1 case where inlet and outlet are closer to the corners of the *** is a 192% difference between the moisture reduction of these two cases at Re=250,T=80℃ and t=120 min.

关键词： convective drying porous domain cavity flow inlet/exit port finite element method

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

A thermodynamic perspective on electrode poisoning in solid oxide fuel cells

引用

International Journal of Minerals,Metallurgy and Materials 2024年第6期31卷 1449-1455页

作者： Kevin Huang department of mechanical Engineering University of South CarolinaColumbiaUSA

A critical challenge to the commercialization of clean and high-efficiency solid oxide fuel cell(SOFC)technology is the insuf-ficient stack lifespan caused by a variety of degradation mechanisms,which are associated with cell components and chemical *** components related degradation refers to thermal/chemical/electrochemical deterioration of cell materials under operating conditions,whereas the latter regards impurities in feedstocks of oxidant(air)and reductant(fuel).This article provides a thermodynamic perspective on the understanding of the impurities-induced degradation mechanisms in *** discussion focuses on using thermodynamic ana-lysis to elucidate poisoning mechanisms in cathodes by impurity species such as Cr,CO_(2),H_(2)O,and SO_(2) and in the anode by species such as S(or H_(2)S),SiO_(2),and P_(2)(or PH_(3)).The author hopes the presented fundamental insights can provide a theoretical foundation for search-ing for better technical solutions to address the critical degradation challenges.

关键词： impurities air fuel reaction activity

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Characterization and Analysis of Inconel 718 Alloy Ground at Different Speeds

引用

Chinese Journal of mechanical Engineering 2024年第2期37卷 137-149页

作者： Hao Liu Huili Han Qinghong Jiang Minglin He Bi Zhang department of mechanical and Energy Engineering Southern University of Science and TechnologyShenzhen 518055China department of mechanical Engineering Hong Kong Polytechnic UniversityHong KongChina

Inconel 718(IN718)alloy is widely applied to fabricate high temperature resistant or corrosion resistant parts due to its excellent mechanical ***,the machining of IN718 alloy is difficult as it may cause serious tool wear and poor surface quality(SQ)of the *** this work,grinding experiments on IN718 alloy at different speeds were conducted by using a CBN grinding *** relationship between grinding speed,SQ and subsurface damage(SSD)was well *** increasing grinding speed,surface roughness decreased,and SQ was greatly ***,the microhardness of the grinding surface declined as the grinding speed *** SSD depth was almost unchanged when the grinding speed was lower than 15 m/s,then it decreased with higher grinding *** was attributed to the mechanical-thermal synergistic effect in the grinding *** results indicated that increasing grinding speed can effectively improve the SQ and reduce the SSD of IN718 *** conclusion in the work may also provide insight into processing other hard-to-machining materials.

关键词： Surface integrity Grinding speed IN718 alloy Precision machining CBN grinding wheel

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Locomotion control of a rigid-soft coupled snake robot in multiple environments

引用

Biomimetic Intelligence & Robotics 2024年第2期4卷 12-23页

作者： Xuanyi Zhou Yuqiu Zhang Zhiwei Qiu Zhecheng Shan Shibo Cai Guanjun Bao College of mechanical Engineering Zhejiang University of TechnologyHangzhou 310023China State Key Laboratory of Chemical Engineering College of Chemicaland Bioogical EngineringZhejiang UniverstyHangzhou 310027China College of Biomedical Science and Engineering South China University of TechnologyGuangzhou 510000China

The versatile motion capability of snake robots offers themselves robust adaptability in varieties of challenging environments where traditional robots may be *** study reports a novel flexible snake robot featuring a rigid-flexible coupling structure and multiple motion *** better understand the robot's behavior,a bending model for the soft actuator is ***,a dynamic model is developed to map the relationship between the input air pressure and joint torque,which is the model base for controlling the robot *** on the wave motion generated by the joint coupling direction function in different planes,multiple motion gait planning methods of the snake-like robot are *** order to evaluate the adaptability and maneuverability of the developed snake robot,extensive experiments were conducted in complex *** results demonstrate the robot's effectiveness in navigating through intricate settings,underscoring its potential for applications in various fields.

关键词： Snake robot Rigid-flexible coupled Soft actuator Motion gait analysis

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Internal flow in sessile droplets induced by substrate oscillation:towards enhanced mixing and mass transfer in microfluidic systems

引用

Microsystems & Nanoengineering 2024年第3期10卷 369-379页

作者： Tianyi Zhang Peng Zhou Terrence Simon Tianhong Cui department of mechanical Engineering University of MinnesotaMinneapolisMN 55455USA

The introduction of flows within sessile droplets is highly effective for many lab-on-a-chip chemical and biomedical ***,generating such flows is difficult due to the typically small droplet ***,we present a simple,non-contact strategy to generate internal flows in sessile droplets for enhancing mixing and mass *** flows are driven by actuating a rigid substrate into oscillation with certain amplitude distributions without relying on the resonance of the droplet *** oscillation characteristics and corresponding flow patterns are documented *** indices and mass transfer coefficients of sessile droplets on the substrate surface are measured using optical and electrochemical *** demonstrate complete mixing within the droplets in 1.35 s and increases in mass transfer rates of more than seven times static *** of concept was conducted with experiments of silver nanoparticle synthesis and with heavy metal ion sensing employing the sessile droplet as a microreactor for synthesis and an electrochemical cell for *** degrees of enhancement of synthesis efficiency and detection sensitivity attributed to the internal flows are experimentally documented.

关键词： mixing oscillation synthesis

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：