检索结果-南通市图书馆

Effect of pre-twinning and heat treatment on formability of AZX311 Mg alloy

Journal of Magnesium and Alloys 2024年第3期12卷 1154-1169页

作者： mahesh panchal Lalit Kaushik Min-Seong Kim Ravi Kottan Renganayagalu Shi-Hoon Choi Jaiveer Singh Department of Mechanical Engineering Indian Institute of Technology JodhpurKarwarJodhpur 342030RajasthanIndia Department of Metallurgical and Materials Engineering Indian Institute of Technology JodhpurKarwarJodhpur 342030RajasthanIndia Energy Materials Research Center Korea Institute of Science and Technology(KIST)5 Hwarang-roSeongbuk-guSeoul 02792Republic of Korea Department of Advanced Components and Materials Engineering Sunchon National University255 Jungang-roSuncheonJeonnam 57922Republic of Korea

In this study,the effects of pre-strain-induced tensile twins(TTWs)and controlled heat treatment on the formability behavior of AZX311 Mg alloy sheets were investigated.A 4%compressive strain was applied to pre-strain the sheets using the in-plane compression(IPC)technique along the rolling direction(RD)to introduce *** pre-strained(PS)samples were subsequently heat-treated at 250℃,350℃,and 400℃ independently for 1 hr,and are termed as PSA1,PSA2,and PSA3,*** cupping tests were conducted to assess the formability of the sheet samples under different initial *** results showed that the PS sample heat-treated at 250℃ for 1hr exhibited a decrease in the Erichsen index(IE)compared to the as-rolled sample,whereas PSA2 and PSA3 samples showed an increase in IE *** analysis revealed that most of the TTWs generated through pre-twinning were stable at 250℃;however,the twin volume fraction reduced to 41%at 350℃ compared to the PS samples due to enhanced thermal activity at that ***,PSA2 samples showed severe grain coarsening in some areas of the sample,and the fraction of such grains increased in the PSA3 *** stretch formability(IE value)of PSA2 samples showed a 32.3%increase compared to the as-rolled ***,the analysis of the deformed specimen at failure under the Erichsen test indicated that considerable detwinning occurs in the PS and PSA1 samples,whereas dislocation slip activity dominates in the PSA2 and PSA3 samples during stretch *** from detwinning and dislocation slip,deformation twins were also observed in all samples after the Erichsen ***,this work highlights the importance of texture control and its underlying mechanisms via pre-twinning followed by heat treatment and their impact on the room temperature(RT)stretch formability of AZX311 Mg alloy sheets.

关键词： Mg alloys Pre-twinning Texture Formability EBSD.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Recent advances in the in-plane shear testing of Mg alloy sheets

引用

Journal of Magnesium and Alloys 2023年第2期11卷 405-424页

作者： mahesh panchal Lalit Kaushik Ravi K.R Rajesh Khatirkar Shi-Hoon Choi Jaiveer Singh Department of Mechanical Engineering Indian Institute of Technology JodhpurKarwarJodhpur 342030RajasthanIndia Department of Advanced Components and Materials Engineering Sunchon National University255 Jungang-roSuncheonJeonnam 57922Republic of Korea Department of Metallurgical and Materials Engineering Indian Institute of Technology JodhpurKarwarJodhpur 342030RajasthanIndia Department of Metallurgical and Materials Engineering Visvesvaraya National Institute of Technology(VNIT)South Ambazari RoadNagpur 440010MaharashtraIndia

Sheet-metal products are integral parts of engineering industries and academia research. Various testing techniques have revealed the deformation behaviors of sheet metals under complex stress states. Information obtained from tensile and compression tests, however, are insufficient for the identification of material parameters relevant to modern constitutive laws, which require experimental setups capable of generating various loading conditions and applying great amounts of strain to sheet metals. In-plane shear testing has emerged as an important method to overcome the challenges associated with tension and compression tests and can provide additional information about deformation behaviors under large plastic strains. Materials such as Mg alloys with poor levels of both ductility and formability cannot accommodate large plastic strains. Therefore, tension and compression tests have limitations in explaining the material behaviors that occur during sheet metal forming where large plastic strains are introduced. Many studies have been conducted to explain the deformation behaviors of Mg alloys under shear deformation techniques. These include severe plastic deformation(SPD), especially the equal channel angular pressing(ECAP)and equal channel angular extrusion, rolling combined with shear deformation i.e. differential speed rolling(DSR), and also in-plane shear for sheet metals, particularly under large levels of plastic strain. These in-plane shear technique involves the Miyauchi shear test, ASTM shear test, and twin bridge shear tests. Moreover, many experimental results have revealed that the evolution of microstructure and texture during in-plane shear is closely related to the failure behavior of materials. Therefore, this review is focused on techniques for in-plane shear testing that have been reported thus far, on the effect of in-plane shear on the microstructure development of Mg alloy sheets, and on the usefulness of in-plane shear testing to evaluate t

关键词： Mg alloys In-plane shear Texture Formability EBSD

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：