检索结果-南通市图书馆

journal of Materials Science & Technology 2021年第12期71卷 228-240页

作者： H.T.jeong W.j.kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul 121-791Republic of Korea

Ultrafine-grained alloys fabricated by severe plastic deformation(SPD)have high strength but often poor uniform *** via high-ratio differential speed rolling(HRDSR)followed by an annealing treatment was applied to Al_(0.5)CoCrFeMnNi to design the microstructure from which both high strength and high uniform strain can be *** optimized microstructure was composed of an ultrafine-grained FCC matrix(1.7-2μm)with a high fraction of high-angle grain boundaries(61%-66%)and ultrafine BCC particles(with a size of 0.6-1μm and a volume fraction of8%-9.3%)distributed uniformly at the grain boundaries of the FCC *** the severely plastically deformed microstructure,the nucleation kinetics of the BCC phase was *** static recrystallization(CSRX)took place during the annealing process at 1273 *** of the BCC phase particles occurring concurrently with CSRX effectively retarded the grain growth of the FCC *** precipitation of the hard and brittleσphase was,however,*** annealed sample processed by HRDSR with the optimized microstructure exhibited a high tensile strength of over 1 GPa with a good uniform elongation of 14%-20%.These tensile properties are comparable to those of transformation-induced plasticity *** mechanisms of the severely plastically deformed alloy before and after annealing were identified,and each strengthening mechanism contribution was *** calculated results matched well with the experimental results.

关键词： High entropy alloys Severe plastic deformation Uniform ductility High strength Dual phase Annealing

Grain size and temperature effect on the tensile behavior and deformation mechanisms of non-equiatomic Fe(41)Mn(25)Ni(24)Co8Cr2high entropy alloy

在线全文

学校读者我要写书评

暂无评论

journal of Materials Science & Technology 2020年第7期42卷 190-202页

作者： H.T.jeong W.j.kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul121-791Republic of Korea

The effect of the grain size on the tensile properties and deformation mechanisms of a nonequiatomic Fe(41)Mn(25)Ni(24)Co8 Cr2 high-entropy alloy was studied in the temperature range between 298 and 1173 K by preparing the samples with three different grain sizes through severe plastic deformation and subsequent annealing:ultrafine(sub)grain size(≤0.5μm),8.1μm and 590.2μ*** the temperature between 298 and773 K,the material with the large grain size of 590.2μm exhibited the largest tensile ductility(57%-82%)due to its high strain hardening associated with mechanical twinning,but it exhibited the lowest strength due to its large grain *** material with the ultrafine(sub)grain size exhibited the lowest tensile ductility(3%-7%)due to a greatly reduced strain hardening ability after severe plastic deformation,but it exhibited the highest strength due to the dislocation strengthening and grain refinement *** tensile testing at temperatures above 973 K,recrystallization occurred in the material with the ultrafine(sub)grains during the sample heating and holding stage,leading to the formation of fine and equiaxed grains with the sizes of 6.8-13.5μ*** deformation behavior of the Fe(41)Mn(25)Ni(24)Co8 Cr2 with different grain sizes in the high temperature range between 973 and 1173 K,where pseudosteady-state flow was attained in the stress-strain curves,could be explained by considering the simultaneous contribution of grain boundary sliding and dislocation-climb creep to total plastic *** activation energies for plastic flow for the materials with different grain sizes were similar as^199 kj/*** predicting the deformation mechanism,it was important to consider the change in grain size by rapid grain growth or recrystallization during the sample heating and holding stage because grain boundary sliding is a grain-size-dependent deformation *** sample with the ultrafine(sub)grains exhibited the large tensile elongations of 30%-85%due to it

关键词： High entropy alloys Grain size High temperature deformation mechanism Tensile behavior Grain boundary sliding

Effect of roll speed ratio on the texture and microstructural evolution of an FCC high-entropy alloy during differential speed rolling

在线全文

学校读者我要写书评

暂无评论

journal of Materials Science & Technology 2022年第16期111卷 152-166页

作者： H.T.jeong W.j.kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul 121-791Republic of Korea

A very coarse-grained(335μm)Fe_(41)Mn_(25)Ni_(24)Co_(8)Cr_(2)high-entropy alloy with a single FCC phase was cold rolling to a 80%reduction in thickness using the differential speed rolling technique with various speed ratios(SRs)ranging between 1 and *** the SR was increased,the volume fraction of the region of high-density micro-shear bands increased to accommodate the higher shear *** SR=4,the entire thickness of the sheet was covered with micro-shear bands,and ultrafine(sub)grains with a size of1.4μm were uniformly formed along the shear bands.A continuous dynamic recrystallization(CDRX)mechanism occurred during rolling,and a higher SR accelerated the CDRX *** conventional rolling(at SR=1),a brass{110}orientation texture with minor components of S{123}and Cu{112}orientations *** higher SRs,shear texture developed as the main type,while the development of rolling texture was *** microstructure at SR=4 obtained after annealing at973 K showed a fully recrystallized microstructure composed of a five times smaller grain size(4μm)with a higher intensity ofγfiber texture compared with that prepared by conventional *** samples processed with high SRs exhibited better tensile properties compared with the conventionally rolled sample in terms of strength and ductility after *** current results demonstrate that by using differential speed rolling with a high SR,one can achieve a significantly finer and more homogeneous microstructure,stronger shear texture,and superior tensile mechanical properties for an FCC high-entropy alloy compared to that obtained by conventional *** strength of the as-rolled and annealed samples was quantitatively explained by considering the contribution of grain size and dislocation density to strengthening.

关键词： High entropy alloys Differential speed rolling Texture Grain refinement Strength Severe plastic deformation

Effects of grain size and Al addition on the activation volume and strain-rate sensitivity of CoCrFeMnNi high-entropy alloy

在线全文

学校读者我要写书评

暂无评论

journal of Materials Science & Technology 2023年第12期143卷 242-252页

作者： H.T.jeong W.j.kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul121-791Republic of Korea

The activation volume(V∗)and strain-rate sensitivity exponent(m)of CoCrFeMnNi and Al_(0.5)CoCrFeMnNi high entropy alloys(HEAs)with various grain sizes(ranging between 2.4 and 356μm)were measured at different strain rates and strain levels at room *** the strain rate decreased,the plastic strain decreased,and the grain size increased,V∗*** enhanced solid-solution strengthening by addition of aluminum decreased V∗.The Hassen plot was modified to capture the grain-size depen-dence of V∗by considering the grain-size dependence of the dislocation *** the plastic strain increased,the strain rate decreased,and the grain size decreased,m *** behavior of m could be quantitatively predicted by using equations derived for the grain-size-dependent V∗and flow *** difference in the grain-size dependence of m between conventional face centered cubic(FCC)metals and FCC HEAs over the nanograin size range could not be explained in terms of a relatively large Hall-Petch slope of the FCC HEAs compared with that of the FCC conventional metals,but was explainable in terms of a substantially higher probability of activation of grain-boundary diffusion-controlled grain-boundary-sliding mechanism at nanograin sizes in the FCC conventional metals than in the FCC HEAs.

关键词： Grain size High entropy alloys Activation volume Strain-rate sensitivity Solid solution

MOLECULAR DESIGN OF LIGHT EMITTING POLYMERS

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Chinese journal of Polymer Science 2000年第3期18卷 227-237页

作者： j.W.Yu j.K.kim j.MHong Y.C.kim H.N.Cho D.Y.kim C.Y.kim Polymer Materials Laboratory Korea Institute of Science and TechnologyP.O.Box 131CheongryangSeoul 130-650.Korea

Fluorene-based alternating and statistical copolymers were synthesized by employing reaction methods of Wittig,Heck and *** copolymers were classified into three groups with the photoluminescence(PL)emission maxima at420,475 and 500 nm,*** copolymers with two chromophores having PL emission maxima at 420 and475 nm emitted light with the emission maximum at 475 nm on photoexcitation at 365 nm and improved the quantumefficiency by the energy ***,the intramolecular energy transfer was inefficient compared to the intermolecularenergy transfer when the two chromophores were apart from each other in the range of the Forster critical ***-pyridinedivinylene alternating copolymer was synthesized by the Wittig reaction and found to have physical,electronic andelectrochemical properties of the individual units *** double-layered light emitting diode(LED)with the statisticalcopolymer as an emitting layer and the pyridine-containing copolymer as an electron transporting-hole blocking layer,whichwere sandwiched between ITO and Al,displayed a quantum efficiency of 0.1%.

关键词： Light emitting polymers

Aqueous-processable,naphthalene diimide-based polymers for eco-friendly fabrication of high-performance,n-type organic electrolyte-gated transistors

在线全文

学校读者我要写书评

暂无评论

Science China Chemistry 2022年第5期65卷 973-978页

作者： Dahyun jeong Min je kim Seungjin Lee jin-Woo Lee Youngwoong kim Hyeong jun kim jeong Ho Cho Bumjoon j.kim Department of Chemical and Biomolecular Engineering Korea Advanced Institute of Science and Technology(KAIST)Daejeon 34141Republic of Korea Department of Chemical and Biomolecular Engineering Yonsei UniversitySeoul 03722Republic of Korea Department of Chemical and Biomolecular Engineering Sogang UniversitySeoul 04107Republic of Korea

Organic electrolyte-gated transistors(OEGTs) have the benefits of low power consumption and large current ***,the electrical performance of n-type OEGTs lags far behind that of p-type *** this study,we design a series of polymers,P(NDITEG-T) and P(NDIMTEG-T),comprising a naphthalene diimide backbone for n-type charge transport and oligo(ethylene glycol)(OEG) side chains for high ionic conductivity and eco-friendly solution *** incorporation of the OEG chain facilitates the electrochemical doping of the semiconductor by ions to realize high-performance,n-type ***,in OEGTs,P(NDITEG-T) achieves a high electron mobility of 1.0 × 10^(-1) cm^(2) V^(-1) s^(-1),which represents the highest value reported for solution-processed,n-type *** is noted that the fabrication of the OEGTs is achieved by solution processing with eco-friendly ethanol/water mixtures in virtue of the hydrophilic OEG *** work demonstrates the molecular design of the P(NDITEG-T) polymer and its significant ability to produce aqueous-processable,high-performance,and n-type OEGTs.

关键词： organic electrolyte-gated transistors n-type transistors oligo(ethylene glycol)polymers eco-friendly solution process high electron mobility

The Stanley neuropathology Consortium Integrative Database (SNCID) for Psychiatric Disorders

在线全文

学校读者我要写书评

暂无评论

neuroscience Bulletin 2019年第2期35卷 277-282页

作者： Sanghyeon kim Maree j.Webster Stanley Brain Research Laboratory Stanley Medical Research Institute

The Stanley Medical Research Institute(SMRI)is a nonprofit organization with a primary mission to fund research on the cause and treatment of severe mental *** SMRI also supports a brain bank as part of the mission to facilitate research into mental *** SMRI brain bank distributes postmortem samples from individuals with serious mental illness,free of charge,to scientists around the *** SMRI brain bank is recognized for the unique way it is set up,organized,and *** of demographically-matched groups of patients with schizophrenia,bipolar disorder(BP),or major depression(DEP)and unaffected controls are organized such that all researchers applying for tissue received samples from the same cohort.

关键词： SNCID for Psychiatric Disorders DRD RNA

Difference in the Hot Compressive Behavior and Processing Maps between the As-cast and Homogenized Al-Zn-Mg-Cu(7075) Alloys

在线全文

学校读者我要写书评

暂无评论

journal of Materials Science & Technology 2016年第7期32卷 660-670页

作者： S.Y. Park W.j. kim Department of Materials Science and Engineering Hongik University 72-1 Sangsu-dong Mapo-gu Seoul 121-791 Republic of Korea Advanced Fusion Process R&D Group Korea Institute of Industrial Technology 994-32 Dongchun-dong Yeonsu-gu Incheon 406-130 Republic of Korea

The deformation mechanisms and processing maps of the as-cast Al-Zn-Mg-Cu （？0？5） aluminum （AI） alloy were studied and compared with those of the homogenized 7075 Al alloy in the temperature range of 573-723 K and in the strain rate range of 10 3-10 s-1 to explore a possibility for directly using the as- cast 7075 Al alloy as a billet for hot working. The as-cast and homogenized 7075 A1 alloys had similar grain sizes and showed similar high-temperature deformation behaviors. The as-cast 7075 Al alloy, however, exhibited higher power efficiencies and smaller unstable flow regions compared to the homogenized 7075 AI alloy because of the presence of secondary phases （MgZn2） segregated at the dendritic interfaces in the as-cast microstructure, which were formed during non-equilibrium solidification. These segregated phases provided nucleation sites for dynamic recovery or continuous dynamic recrystallization, and as a result a fine and more homogeneous （sub）grain structure could be obtained from the as-cast micro- structure compared to the homogenized microstructure. The current work suggested the possibility and advantage of using as-cast microstructures for hot working of aluminum alloys with high content of solutes.

关键词： Al-based alloysProcessing mapHot compressionAs-cast microstructureSegregationRecrystallization

Critical review of superplastic magnesium alloys with emphasis on tensile elongation behavior and deformation mechanisms

在线全文

学校读者我要写书评

暂无评论

journal of Magnesium and Alloys 2022年第5期10卷 1133-1153页

作者： H.T.jeong W.j.kim Department of Materials Science and Engineering Hongik UniversitySangsu-dong 72-1 Mapo-guSeoul 121-791South Korea

The tensile elongation behavior and deformation mechanisms of superplastic Mg alloys and Mg composites were examined by extensively reviewing the literature published from the time of the first report on the superplasticity of Mg alloys to the present *** on the superplasticity of Mg alloys have been conducted mainly on Mg-Al-Zn(AZ)series alloys,Mg-Zn-Zr(ZK),Mg-Li and Mg-RE(rare earth)alloys,and in recent years,Mg-RE alloys have attracted the greatest *** effect of grain size and the type and amount of secondary phase particles on the superplasticity of Mg alloys was systematically examined and *** alloys processed by severe plastic deformation(SPD)and powder-metallurgy methods have smaller grain sizes and exhibit superior superplasticity compared to conventionally processed(by extrusion and rolling)Mg *** the AZ alloys,as the volume fraction of the Mg17Al12phase increases,smaller grains are obtained,and the low-temperature superplasticity(LTS)and high-strain-rate superplasticity(HSRS)characteristics become *** ZK60 alloy with finely dispersed Mg Zn2particles exhibits excellent LTS,while the Mg-RE alloys with a high fraction of thermally stable particles exhibit excellent ***-Li alloys can exhibit LTS even at room temperature due to the presence of a high-volume fraction of the body centered cubic(BCC)phase where atomic diffusivity is *** boundary diffusion-and lattice diffusion-controlled grain boundary sliding are found to operate as the dominant deformation mechanisms below~473 K and above~673 K,respectively,at small grain *** mechanism maps were constructed based on the analysis of the deformation behavior of superplastic Mg alloys,and from the maps,the critical conditions for achieving LTS,HSRS and simultaneous achievement of LTS and HRSR were calculated and proposed,and their importance was discussed.

关键词： Magnesium alloys Superplastic Grain size Secondary phase Grain boundary sliding

Effect of refinement of grains and icosahedral phase on hot compressive deformation and processing maps of Mg-Zn-Y magnesium alloys with different volume fractions of icosahedral phase

在线全文

学校读者我要写书评

暂无评论

journal of Materials Science & Technology 2019年第1期35卷 181-191页

作者： T.Y.Kwak W.j.kim Department of Materials Science and Engineering Hongik University

The effect of the volume fraction of I-phase on the hot compressive behavior and processing maps of the extruded Mg-Zn-Y alloys was examined, and the obtained results were compared with those of the cast alloys in a previous work. The average grain sizes, fractions of dynamically recrystallized(DRXed) grains,and sizes of DRXed grains of the extruded alloys after compressive deformation were significantly smaller,higher and smaller, respectively, than those of the cast alloys after compressive deformation under the same experimental conditions. This was because the microstructures of the extruded alloys, having much more grain boundaries and more refined I-phase particles than the cast alloys, provided a larger number of nucleation sites for dynamic recrystallization than those of the cast alloys. The constitutive equations for high-temperature deformation of the extruded and cast alloys could be derived using the same activation energy for plastic flow, which was close to the activation energy for lattice diffusion in *** with the cast alloys, the onset of the power law breakdown(PLB) occurred at larger ZenerHolloman(Z) parameter values in the extruded alloys. This was because the extruded alloys had finer initial grain sizes and higher fractions of finer DRXed grains compared to the cast alloys, such that the onset of PLB caused by creation of excessive concentrations of deformation-induced vacancies was delayed to a higher strain rate and a lower temperature. The flow-stress difference between the extruded alloys and the cast alloys could be attributed to the difference in the fraction of DRXed grains. According to the processing maps, the extruded alloys exhibited higher power dissipation efficiency and flow stability than the cast alloys. This agreed with the microstructural observations.

关键词： Hot compression Magnesium alloy Processing map Grain refinement Dynamic recrystallization