检索结果-南通市图书馆

Designing hetero-structured ultra-strong and ductile Zr-2.5Nb alloys:Utilizing the grain size-dependent martensite transformation during quenching

引用

journal of Materials Science & Technology 2022年第30期125卷 198-211页

作者： S.y.Liu j.y.Zhang j.Kuang X.y.Bao D.D.Zhang C.L.Zhang j.K.yang G.Liu j.Sun State Key Laboratory for Mechanical Behavior of Materials Xi’an Jiaotong UniversityXi’an 710049China

To further improve the service performance of Zr-2.5Nb alloy worked as pressure tubes in pressurized heavy water reactors,more investigation about the microstructure and thermomechanical processing route of Zr-2.5Nb alloy need to be *** this work,a hetero-structured Zr-2.5Nb alloy was prepared by applying a novel *** analysis reveals that the alloy exhibits a grain sizedependent martensite substructure transition during post-rolling *** hetero-structure consists of equiaxed primaryαgrains and the lamellae groups containing both parallelα’dislocation martensite andα’twin *** with the previously reported Zr-Nb alloys,the present Zr-2.5Nb alloys manifest the highest yield strength(∼710 MPa),together with a high ultimate tensile strength(∼844 MPa)and good ductility(∼17.1%).The enhanced mechanical properties are found to arise from the properly controlled fraction/size of the two types of martensite,which not only significantly strengthens the alloy but also contributes to a stronger strain hardening.A model based on the grain-size-dependent critical resolved shear stress for dislocation slip and twinning has been proposed to explain theα’martensite substructures transition at a critical grain size dc=3.3μ*** this size,the critical resolved shear stress(CRSS)for twinning is higher than that for the***,theα’dislocation martensite is more favorable to ***,theα’twin martensite would exhibit a high *** present work indicates that making use of the grain size-dependent martensite transformation to tailor the heterostructure in Zr alloys is an effective strategy to overcome the strength–ductility trade-off in the material.

关键词： Zr-Nb alloys Heterogeneous structure Martensitic transformation Grain size Strength

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Mechanosynthesis and mechanochemical treatment of bismuth-doped vanadium phosphorus oxide catalysts for the partial oxidation of n-butane to maleic anhydride

引用

journal of Natural Gas Chemistry 2008年第3期17卷 232-237页

作者： y. H. Taufiq-yap y.C. Wong y. Kamiya W.j. Tang Putra Center for Catalysis Science and Technology Department of Chemistry Faculty of Science Universiti Putra Malaysia 43400 UPM Serdang Selangor Darul Ehsan Malaysia Graduate School of Environmental Science Hokkaido Universit3 Sapporo 060-0810 Japan

Three Bi-doped vanadyl pyrophosphate catalysts were prepared via dihydrate route （VPD method）, which consisted of different preparation methods including mechanosynthesis, mechanochemical treatment, and the conventional reflux method. The catalysts produced by the above three methods were characterized by x-ray diffraction （XRD）, scanning electron microscopy （SEM）, and temperature programmed reduction （TPR）. Catalytic evaluation for the partial oxidation of n-butane to maleic anhydride （MA） was also carried out. The XRD patterns of all the Bi-doped catalysts showed the main peaks of pyrophosphate phase. Lower intensity peaks were observed for the mechanochemically treated Bi-doped catalyst （VPDBiMill） with two additional small peaks corresponding to the presence of a small amount of V5＋ phase. The TPR profiles showed that the highest amount of active oxygen species, i.e, V4＋–O- pair, responsible for n-butane activation, was removed from VPDBiMill. Furthermore, from the catalytic test results, the graph of selectivity to MA as a function of the conversion of n-butane demonstrated that VPDBiMill was the most selective catalyst. This suggests that the mechanochemical treatment of vanadium phosphate catalyst （VPDBiMill） is a potential method to improve the catalytic properties for the partial oxidation of n-butane to maleic anhydride.

关键词： mechanosynthesis mechanochemical treatment bismuth vanadyl pyrophosphate

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Propagation behavior of elastic waves in one-dimensional piezoelectric/piezomagnetic phononic crystal with line defects

引用

Acta Mechanica Sinica 2014年第5期30卷 703-713页

作者： y.Pang F.-y.jiao j.-X.Liu Department of Engineering Mechanics Shijiazhuang Tie Dao University School of Mathematics and Physics University of Science and Technology Beijing

Using a stiffness matrix method, we in- vestigate the propagation behaviors of elastic waves in one-dimensional （1D） piezoelectric/piezomagnetic （PE/PM） phononic crystals （PCs） with line defects by calculating energy reflection/transmittion coefficients of quasi-pressure and quasi-shear waves. Line defects are created by the re- placement of PE or PM constituent layer. The defect modes existing in the first gap are considered and the influences on defect modes of the material properties and volume fraction of the defect layers, the type of incident waves, the location of defect layer and the number of structural layers are discussed in detail. Numerical results indicate that defect modes are the most obvious when the defect layers are inserted in the middle of the perfect PCs; the types of incidence wave and material properties of the defect layers have important effects on the numbers, the location of frequencies and the peaks of defect modes, and the defect modes are strongly de- pendent on volume fraction of the defect layers. We hope this paper will be found useful for the design of PE/PM acoustic filters or acoustic transducer with PCs structures.

关键词： 1D phononic crystal Piezoelectric/piezomag- netic. Elastic wave Line defect Stiffness matrix method

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

MICROSTRUCTURE ANALySIS AND MECHANICAL PROPERTIES OF Zn-Al ALLOy ROD PRODUCED By HEATED MOLD CONTINUOUS CASTING

引用

Acta Metallurgica Sinica(English Letters) 2003年第3期16卷 241-248页

作者： y.Ma y.Hao F.y.yan H.j.Liu State Key Laboratory of Advanced Nonferrous Materials Lanzhou University of Science & Technology Lanzhou 730050 ChinaState Key Laboratory of Advanced Nonferrous Materials Lanzhou University of Science & Technology Lanzhou 730050 ChinaState Key Laboratory of Advanced Nonferrous Materials Lanzhou University of Science & Technology Lanzhou 730050 ChinaSchool of Mechano-Electronic EngineeringHua Qian University Quanzhou 362011China

The new technology of continuous casting by heated mold was used to produce directional solidification ZA alloy lines to eliminate the inter defects of these lines and increase their mechanical properties. The results are as follows: (1) The microstruc-ture of the ZA alloy lines is the parallel directional dendritic columnar crystal. Every dendritic crystal of eutectic alloy ZA5 was composed of many layer eutectic β and η phases. The micro structure of hypereutectic ZA alloys is primary dendritic crystal and interdendritic eutectic structure. The primary phase of ZA8 and ZA12 is β, among them, but the primary phase of ZA22 and ZA27 is a. (2) Through the test to the as-cast ZA alloy lines made in continuous casting by heated mold, it is found that the tensile strength and hardness increase greatly, but the elongation decreases. With the increase of aluminum amount from ZA 5 to ZA 12, ZA22 and ZA27, the tensile strength increases gradually. ZA27 has the best comprehensive mechanical properties in these four kinds of ZA alloys. (3) Heat treatment can decrease the dendritic segregation and improve the elongation of ZA alloy, but make their strength decrease slightly.

关键词： zinc-aluminum alloy heated mold continuous casting mechanical properties heat treatment

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

ON THE IDENTIFICATION OF RESIDUAL IMPACT PROPERTIES OF MATERIALS By ACOUSTO-ULTRASONICS——A PATTERN RECOGNITION APPROACH

引用

Acta Mechanica Sinica 1995年第1期11卷 34-43页

作者： G.j.Molina y.M.Haddad Dept.of Mechanical Engineering University of OttawaOttawaCanada K1N 6N5

This paper deals with the application of Acousto-ultrasonics,in con- junction with Pattern Recognition and Classification techniques,to the identification of residual impact properties of a class of polymeric material,namely,Polyvinylchlo- ride(PVC).PVC specimens of different low-energy repeated impact damage states are processed by Acousto-ultrasonics(AU)to retrieve AU signals in the form of dig- italized *** AU signals are grouped as distinct classes,each pertaining to a known level of repeated impact *** features of these AU signals are used to build Pattern Recognition(PR)*** classifiers are used to identify unknown damage states in other PVC specimens by classifying the re- trieved AU signals as belonging to one of the *** obtained results indicate that Acousto-ultrasonics in combination with Pattern Recognition and Classification techniques can be used for the quantitative non-destructive identification of damage states in PVC specimens of unknown low-energy repeated impact conditions.

关键词： pattern recognition acousto-ultrasonics impact damage quantitative non-destructive examination

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Microstructure and brazing mechanism of porous Si_3N_4/Invar joint brazed with Ag-Cu-Ti/Cu/Ag-Cu multi-layered filler

引用

journal of Materials Science & Technology 2018年第4期34卷 713-719页

作者： j.Zhang j.y.Liu T.P.Wang School of Materials Science and Engineering Harbin Institute of Technology

Porous Si3N4 was brazed to Invar alloy in this study, and Ag-Cu-Ti/Cu/Ag-Cu multi-layered filler was designed to inhibit the formation of Fe2Ti and Ni3Ti intermetallic compounds. The effects of the brazing temperature and the thickness of Cu interlayer on the microstructure and mechanical properties of brazed joints were investigated. The typical microstructure of the joint brazed with multi-layered filler was porous Si3N4/TiN ＋ Ti5Si3/Ag-Cu eutectic[Cu[Ag-Cu eutectic/Cu-rich layer ＋ diffusion layer/Invar. When the brazing temperature increased, the reaction layer at the ceramic/filler interface grew thicker and the Cu interlayer turned thinner. As the thickness of Cu interlayer increased from 50 to 150 μm, the joint strength first increased and then decreased. In this research, the maximum shear strength （73 MPa） was obtained when being brazed at 1173 K with a 100 μm Cu interlayer applied in the filler, which was 55% higher than that brazed with single Ag-Cu-Ti brazing alloy and had reached 86% of the ceramic. The release of residual stress and the barrier effect of Cu interlayer to inhibit the formation of Fe2Ti and Ni3Ti intermetallics played the major role in the improvement of joint strength.

关键词： Porous Si3N4 Invar alloy Brazing Microstructure Mechanical properties

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Superplastic behavior of an ultrafine-grained Mg-13Zn-1.55y alloy with a high volume fraction of icosahedral phases prepared by high-ratio differential speed rolling

引用

journal of Materials Science & Technology 2017年第9期33卷 919-925页

作者： T.y.Kwak W.j.Kim Rare Metal R&BD Group Korea Institute of Industrial Technology Department of Materials Science and Engineering Hongik University

An ultrafine-grained（UFG） Mg-13Zn-1.55 y alloy（ZW132） with a high volume fraction（7.4%） of icosahedral phase（I-phase, Mg;Zn;y） particles was prepared by applying high-ratio differential speed rolling（HRDSR） on the cast microstructure following homogenization. The alloy exhibited excellent superplasticity at low temperatures(tensile elongations of 455% and 1021% 473 K-10;s;and 523 K-10;s;,respectively). Compared with UFG Mg-9.25Zn-1.66 y alloy（ZW92） with a lower volume fraction of I-phase particles（4.1%）, which was prepared using the same processing routes, the UFG ZW132 alloy exhibited a higher thermal stability of grain size. Rapid grain coarsening, however, occurred at temperatures beyond523 K, leading to a loss of superplasticity. The high-temperature deformation behavior of the HRDSRprocessed ZW132 alloy could be well described assuming that the mechanisms of grain boundary sliding and dislocation climb creep competed with each other and considering that the grain-size was largely increased by accelerated grain growth at the temperatures beyond 523 K.

关键词： Magnesium alloy Superplastic deformation Ultrafine grain Icosahedral quasicrystal Grain growth

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Difference in the Hot Compressive Behavior and Processing Maps between the As-cast and Homogenized Al-Zn-Mg-Cu(7075) Alloys

引用

journal of Materials Science & Technology 2016年第7期32卷 660-670页

作者： S.y. Park W.j. Kim Department of Materials Science and Engineering Hongik University 72-1 Sangsu-dong Mapo-gu Seoul 121-791 Republic of Korea Advanced Fusion Process R&D Group Korea Institute of Industrial Technology 994-32 Dongchun-dong Yeonsu-gu Incheon 406-130 Republic of Korea

The deformation mechanisms and processing maps of the as-cast Al-Zn-Mg-Cu （？0？5） aluminum （AI） alloy were studied and compared with those of the homogenized 7075 Al alloy in the temperature range of 573-723 K and in the strain rate range of 10 3-10 s-1 to explore a possibility for directly using the as- cast 7075 Al alloy as a billet for hot working. The as-cast and homogenized 7075 A1 alloys had similar grain sizes and showed similar high-temperature deformation behaviors. The as-cast 7075 Al alloy, however, exhibited higher power efficiencies and smaller unstable flow regions compared to the homogenized 7075 AI alloy because of the presence of secondary phases （MgZn2） segregated at the dendritic interfaces in the as-cast microstructure, which were formed during non-equilibrium solidification. These segregated phases provided nucleation sites for dynamic recovery or continuous dynamic recrystallization, and as a result a fine and more homogeneous （sub）grain structure could be obtained from the as-cast micro- structure compared to the homogenized microstructure. The current work suggested the possibility and advantage of using as-cast microstructures for hot working of aluminum alloys with high content of solutes.

关键词： Al-based alloysProcessing mapHot compressionAs-cast microstructureSegregationRecrystallization

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of refinement of grains and icosahedral phase on hot compressive deformation and processing maps of Mg-Zn-y magnesium alloys with different volume fractions of icosahedral phase

引用

journal of Materials Science & Technology 2019年第1期35卷 181-191页

作者： T.y.Kwak W.j.Kim Department of Materials Science and Engineering Hongik University

The effect of the volume fraction of I-phase on the hot compressive behavior and processing maps of the extruded Mg-Zn-y alloys was examined, and the obtained results were compared with those of the cast alloys in a previous work. The average grain sizes, fractions of dynamically recrystallized(DRXed) grains,and sizes of DRXed grains of the extruded alloys after compressive deformation were significantly smaller,higher and smaller, respectively, than those of the cast alloys after compressive deformation under the same experimental conditions. This was because the microstructures of the extruded alloys, having much more grain boundaries and more refined I-phase particles than the cast alloys, provided a larger number of nucleation sites for dynamic recrystallization than those of the cast alloys. The constitutive equations for high-temperature deformation of the extruded and cast alloys could be derived using the same activation energy for plastic flow, which was close to the activation energy for lattice diffusion in *** with the cast alloys, the onset of the power law breakdown(PLB) occurred at larger ZenerHolloman(Z) parameter values in the extruded alloys. This was because the extruded alloys had finer initial grain sizes and higher fractions of finer DRXed grains compared to the cast alloys, such that the onset of PLB caused by creation of excessive concentrations of deformation-induced vacancies was delayed to a higher strain rate and a lower temperature. The flow-stress difference between the extruded alloys and the cast alloys could be attributed to the difference in the fraction of DRXed grains. According to the processing maps, the extruded alloys exhibited higher power dissipation efficiency and flow stability than the cast alloys. This agreed with the microstructural observations.

关键词： Hot compression Magnesium alloy Processing map Grain refinement Dynamic recrystallization

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

An SBFEM-Based Model for Hydraulic Fracturing in Quasi-Brittle Materials

引用

Acta Mechanica Solida Sinica 2018年第4期31卷 416-432页

作者： F. yao Z.j. yang y.j. Hu College of Civil Engineering and Architecture Zhejiang University Hangzhou 310058 China School of Civil Engineering Shaoxing University Shaoxing 312000 China

A numerical model based on the scaled boundary finite element method is devel- oped to simulate the hydraulic fracturing in concrete-like quasi-brittle materials using cohesive interface elements. The shadow domain method developed previously （yang and Deeks in Eng Fract Mech 143（4）：333 354, 2007） is extended to consider crack-width-dependent hydraulic pres- sure and cohesive traction, so that the stress intensity factors caused by both crack-face forces are semi-analytically calculated separately in the same way. The crack propagation is determined by the criterion of KI ≥ 0, and the propagation direction by the linear elastic fracture mechanics criteria. Two examples of concrete structures are modeled, and the results are in good agreement with the experimental data and others numerical results.

关键词： Scaled boundary finite element method Hydraulic fracture Cohesive crackmodel Crack propagation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：