检索结果-南通市图书馆

BaTiO3 solid solutions co-doped with Gd3+ and Eu3+:Synthesis,structural evolution and dielectric properties

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

journal of Rare Earths 2024年第10期42卷 1920-1926页

作者： R.martínez-López m.Pérez-Labra j.A.Romero-Serrano F.R.Barrientos-Hernández m.Reyes-Pérez m.I.Valenzuela-Carrillo G.Urbano-Reyes V.E.Reyes-Cruz G.I.Dávila-Pulido Academic Area of Earth Sciences and materials Autonomous University of Hidalgo State metallurgy and materials Department ESIQIE-IPNUPALM Autonomous University of Coahuila Boulevard Adolfo López Mateos S/n

In this paper,the synthesis,structural evolution,and dielectric properties of BaTiO3solid solutions codoped with rare earth elements(Gd3+and Eu3+) prepared using the solid-state reaction method are *** pure precursor powders of BaCl3,TiO2,Gd2O3,and Eu2O3were mixed in stoichiometric proportions,ground in an agate mortar before being uniaxially pressed at 250 mPa and sintered at 1300℃ in air atmosphere for 6 h to obtain Ba1-3xGd2xTi1-3xEu4xO3（x=0,0.0015,0.01 and0.1）.X-ray diffraction（XRD） and Rietveld's refinement results reveal the crystal phase ferroelectric tetragonal BaTiO3for the samples with x=0,0.0015 and 0.01, as well as a consistent increment in the lattice parameters caused by the *** solubility limit of Gd3+and Eu3+in the BaTiO3structure is reached for the sample with x>0.01,and the orthorhombic Eu2TiO5and monoclinic BaTi2O5secondary phases were *** Raman results show the characteristic peaks of ferroelectric tetragonal BaTiO3around 716 cm-1（LO of A1 symmetry）,515 cm-1（TO of A1 symmetry）,and 305 cm-1（B1）.The maximum relative permittivity measured at 1 kHz was recorded to be 6151.8 for the sample with x=0.0015,and a decrease in the Curie temperature to 105℃ with respect to the undoped sample was *** punctual microanalysis for the samples with x=0.0015,0.01,and 0.1 reveals grains composed of Ba,Ti,O,Gd,and Eu homogeneously distributed in the *** Ba/Ti ratios for samples with x=0.0015,0.01 and 0.1 are 2.86,2.91,and 0.68,respectively,indicating substitution at the Ti site for samples with x=0.0015 and 0.01 and a substitution at the Ba site for the sample with x=0.1.

关键词： BaTiO3 Doping Europium Gadolinium Rare earths Synthesis

Frequency-dependent viscoelasticity effects on the wave attenuation performance of multi-layered periodic foundations

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Applied mathematics and mechanics(English Edition) 2024年第3期45卷 407-424页

作者： m.SAFI m.VAKILIFARD m.j.mAHmOODI Faculty of Civil Water&Environmental EngineeringShahid Beheshti UniversityTehran ***Iran Faculty of mechanical and Energy Engineering Shahid Beheshti UniversityTehran ***Iran

In this paper,layered periodic foundations(LPFs)are numerically examined for their responses to longitudinal and transverse modes in the time and frequency *** different unit-cells,i.e.,2-layer,4-layer,and 6-layer unit-cells,comprising concrete/rubber,concrete/rubber/steel/rubber,and concrete/rubber/steel/rubber/lead/rubber materials,respectively,are taken into ***,the viscoelasticity behavior of the rubber is modeled with two factors,i.e.,a frequency-independent(FI)loss factor and a linear frequency-dependent(FD)loss *** the extraction of the complex dispersion curves and the identification of the band gaps(BGs),the simulations of wave transmission in the time and frequency domains are performed using the COmSOL *** parametric studies evaluate the effects of the rubber viscoelasticity models on the dispersion curves and the wave transmission for the longitudinal and transverse *** results show that considering the rubber viscoelasticity enhances the wave attenuation ***,the transverse-mode damping is more sensitive to the viscoelasticity model than its longitudinal *** 6-layer unit-cell LPF exhibits the lowest BG,ranging from 4.8 Hz to 6.5 Hz.

关键词： layered metamaterial periodic foundation complex dispersion curve wave transmission diagram

Strong Connections and Invertible Weak Entwining Structures

在线全文

学校读者我要写书评

暂无评论

Acta mathematica Sinica,English Series 2012年第7期28卷 1443-1460页

作者： j. N. ALONSO LVAREZ j. m. fern ndez vilaboa GONZ LEZ RODR íGUEZ Departamento de matemáticas Universidad de VigoCampus Universitario Lagoas-Marcosende Departamento de lxebra Universidad de Santiago de Compostela Departamento de matemática Aplicada Ⅱ Universidad de VigoCampus Universitario Lagoas-Marcosende

In this paper we obtain a criterion under which the bijectivity of the canonical morphism of a weak Galois extension associated to a weak invertible entwining structure is equivalent to the existence of a strong connection form. Also we obtain an explicit formula for a strong connection under equivariant projective conditions or under coseparability conditions.

关键词： monoidal category invertible weak entwining structure strong connection weak Galois extension

Selection of digital fabrication technique in the construction industry--A multi-criteria decision-making approach

在线全文

学校读者我要写书评

暂无评论

Frontiers of Structural and Civil Engineering 2024年第7期18卷 977-997页

作者： m.P.SALAImANImAGUDAm j.jAYAPRAKASH Department of Structural and Geotechnical Engineering School of Civil EngineeringVellore Institute of TechnologyVellore 632014India

Digital fabrication techniques,in recent decades,have provided the basis of a sustainable revolution in the construction ***,selecting the digital fabrication method in terms of manufacturability and functionality requirements is a complex *** paper presents alternatives and criteria for selection of digital fabrication techniques by adopting the multi-criteria decision-making *** alternatives considered in the study are concrete three-dimensional(3D)printing,shotcrete,smart dynamic casting,material intrusion,mesh molding,injection concrete 3D printing,and thin forming *** criteria include formwork utilization,reinforcement incorporation,geometrical complexity,material enhancement,assembly complexity,surface finish,and build *** demonstrates different multi-criteria decision-making techniques,with both subjective and objective weighting *** given ranking is based on the current condition of digital fabrication in the construction *** study reveals that in the selection of digital fabrication techniques,the criteria including reinforcement incorporation,build area,and geometrical complexity play a pivotal role,collectively accounting for nearly 70% of the overall *** the evaluated techniques,concrete 3D printing emerged as the best performer,however the shotcrete and mesh molding techniques in the second and third positions.

关键词： digital fabrication multicriteria decision-making concrete 3D printing

Lattice Boltzmann method formulation for simulation of thermal radiation effects on non-Newtonian Al_(2)O_(3) free convection in entropy determination

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Applied mathematics and mechanics(English Edition) 2024年第6期45卷 1085-1106页

作者： m.NEmATI m.SEFID A.KARImIPOUR A.j.CHAmKHA Faculty of mechanical Engineering Yazd UniversityYazd ***Iran Department of mechanical Engineering Najafabad BranchIslamic Azad UniversityNajafabad ***Iran Faculty of Engineering Kuwait College of Science and TechnologyDoha 35004Kuwait

The simultaneous investigation on the parameters affecting the flow of electrically conductive fluids such as volumetric radiation,heat absorption,heat generation,and magnetic field(mF)is very vital due to its existence in various sectors of industry and *** present research focuses on mathematical modeling to simulate the cooling of a hot component through power-law(PL)nanofluid convection *** temperature reduction of the hot component inside a two-dimensional(2D)inclined chamber with two different cold wall shapes is *** formulation of the problem is derived with the lattice Boltzmann method(LBm)by code writing via the FORTRAN *** variables such as the radiation parameter(0–1),the Hartmann number(0–75),the heat absorption/generation coefficient(−5–5),the fluid behavioral index(0.8–1.2),the Rayleigh number(103–105),the imposed mF angle(0°–90°),the chamber inclination angle(−90°–90°),and the cavity cold wall shape(smooth and curved)are *** findings indicate that the presence of radiation increases the mean Nusselt number value for the shear-thickening,Newtonian,and shear thinning fluids by about 6.2%,4%,and 2%,*** most cases,the presence of nanoparticles improves the heat transfer(HT)rate,especially in the cases where thermal conduction dominates *** is the lowest cooling performance index and mF effect for the cavity placed at an angle of 90°.The application in the design of electronic coolers and solar collectors is one of the practical cases of this numerical research.

关键词： thermal performance analysis heat absorption/generation power-law(PL)Al_(2)O_(3)nanofluid magnetohydrodynamics natural convection volumetric radiation inclined cavity

Timing and Spectral Analysis of the Black Hole X-Ray Binary mAXI j1803-298 with Insight-HXmT Data

在线全文

学校读者我要写书评

暂无评论

Research in Astronomy and Astrophysics 2024年第6期24卷 209-224页

作者： Ying-Chen Xu jin-Lu Qu mméndez Rui-Can ma Long ji Liang Zhang Yue Huang Qing-Cui Bu Li-ming Song Key Laboratory of Particle Astrophysics Institute of High Energy PhysicsChinese Academy of SciencesBeijing 100049China University of Chinese Academy of Sciences Chinese Academy of SciencesBeijing 100049China Kapteyn Astronomical Institute University of GroningenP.O.BOX 8009700 AV GroningenThe Netherlands Dongguan Neutron Science Center Dongguan 523808China School of Physics and Astronomy Sun Yat-Sen UniversityZhuhai 519082China Institut für Astronomie und Astrophysik Kepler Center for Astro and Particle PhysicsEberhard Karls UniversitätSand 1D-72076 TübingenGermany

We present a comprehensive analysis of the 2021 outburst of mAXI j1803–298 utilizing observations of the Insight-Hard X-ray modulation Telescope(Insight-HXmT)spanning from the low hard state to the high soft *** the Insight-HXmT data set,compared to the previous work,we identify a more prolonged presence of typeC quasi-periodic oscillations(QPOs)with centroid frequencies ranging from~0.16 to 6.3 Hz,which present correlations with the hardness ratio and the photon index of the Comptonized *** QPO frequencies less than~2 Hz,the QPO phase lags are hard(photons of 10–19 keV arrive later than those of 1–4 keV),while at higher frequencies,the lags become soft at and above~4 ***,the spectra in all Insight-HXmT observations consist of a multi-color blackbody component and a Comptonized component,as commonly observed in classical black hole X-ray *** analyze state transitions and the evolution of accretion geometry in this *** fitted inner disk radius increases abnormally during the low hard state,hypothesized to result from the corona condensing onto the inner ***,two significant drops in flux are observed during the soft intermediate state,maybe implying changes in the corona/jet and the disk,respectively.

关键词： X-rays:binaries accretion accretion disks stars:black holes

Consumer transparency in the production chain for plant varieties produced using new genomic techniques

在线全文

学校读者我要写书评

暂无评论

aBIOTECH 2024年第2期5卷 239-246页

作者： j.m.Lukasiewicz C.C.m.van de Wiel L.A.P.Lotz m.j.m.Smulders Wageningen University&Research P.O.Box 386NL-6700 AJ WageningenThe Netherlands

Plants edited with new genomic techniques(NGTs)currently fall under the Genetically modified Organisms Directive(2001/18/EC)in the European *** the proposal of the European Commission,NGT plants are partially exempted from the regulations of this *** proposal makes a distinction between two categories of NGT plants:NGT-1 and ***-1 category plants are considered equal to plants obtained through conventional breeding *** plants will not be labelled for the consumer,although they will be labelled as ***-2 category plants may be labelled with additional information as a positive *** of seeds of varieties made with gene editing,but not the products,would mean that most steps in the production chain are transparent,but not the last step towards ***“right to know”and increasing knowledge of gene-edited food is a common theme in food labelling towards ***,we describe current labelling regimes and registers and how these may be applied to provide transparency on gene-edited products to ***,we also look into consumer studies,which indicate a greater acceptance of gene-edited food among consumers,especially when additional benefits such as sustainability are mentioned.

关键词： Labelling New genomic techniques Consumer transparency Plant products

Rainfall Sensitivity to microphysics and Planetary Boundary Layer Parameterizations in Convection-Permitting Simulations over Northwestern South America

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

journal of meteorological Research 2024年第4期38卷 805-825页

作者： K.Santiago HERNAndez Sebastian GOmEZ-RIOS juan j.HENAO Vanessa ROBLEDO Alvaro RAmiREZ-CARDONA Angela m.RENDON Geolimna Escuela AmbientalFacultad de IngenieriaUniversidad de AntioquiaMedellin 050010Colombia Grupo de Ingenieria y Gestion Ambiental(GIGA) Escuela AmbientalFacultad de IngenieriaUniversidad de AntioquiaMedellin 050010Colombia Division of Atmospheric Sciences Desert Research InstituteRenoNV 89512USA

Convection-permitting modeling allows us to understand mechanisms that influence rainfall in specific ***,microphysics parameterization(mP) and planetary boundary layer(PBL) schemes remain an important source of uncertainty,affecting rainfall intensity,occurrence,duration,and ***,we study the sensitivity of rainfall to three mP [Weather Research and Forecasting(WRF) Single-moment 6-class(WSm6),Thompson,and morrison] and two PBL [the Yonsei University(YSU) and mellor–Yamada Nakanishi Niino(mYNN)] schemes with a convection-permitting resolution(4 km) over northwestern South America(NWSA).Simulations were performed by using the WRF model and the results were evaluated against soundings,rain gauges,and satellite data,considering the spatio-temporal variability of rainfall over diverse regions prone to deep convection in *** and PBL schemes largely influenced simulated rainfall,with better results for the less computationally expensive WSm6 mP and YSU PBL *** rain gauges and satellite estimates,simulations with morrison mP overestimated rainfall,especially westward of the Andes,whereas the mYNN PBL underestimated precipitation in the Amazon–Savannas *** found that the uncertainty in the rainfall representation is highly dependent on the region,with a higher influence of mP in the Colombian Pacific and PBL in the Amazon–Savannas *** analyzing rainfall-related processes,the selection of both mP and PBL parameterizations exerted a large influence on the simulated lower tropospheric moisture flux and moisture *** schemes significantly influenced the downward shortwave radiation,with mYNN simulating a greater amount of low clouds,which decreased the radiation ***,latent heat fluxes were greater for YSU,favoring moist convection and *** schemes had a marked impact on vertical ***,morrison mP showed stronger convection and higher precipitation rates,which is assoc

关键词： sensitivity microphysics planetary boundary layer(PBL) Weather Research and Forecasting(WRF) processes

Europium recovery process by means of polymeric nanoparticles functionalized with acrylic acid,curcumin and fumaramide

在线全文

学校读者我要写书评

暂无评论

journal of Rare Earths 2024年第10期42卷 1950-1959页

作者： P.A.martínez-montoya j.m.del Río A.de j.morales-Ramirez m.Corea Escuela Superior de Ingeniería Química e Industrias Extractivas ESIQIE-IPNDepartamento de Ingeniería Metalúrgica UPALM S/N Col.Lindavista Escuela Superior de Ingenieria Química e Industrias Extractivas ESIQIE-IPNLaboratorio de Investigación en Polímeros y NanomaterialesUPALM S/N Col.Lindavista Centra de Investigación e Innovación Tecnológica CIITEC-IPNCda.de CECATIs/n

Polymeric nanoparticles of poly(methyl methacrylate) were obtained by emulsion polymerization techniques in a proce ss of two *** particles were functionalized with acrylic acid,curcumin,and fumaramide and three series of polymeric particles were *** incorporation of functional groups was confirmed by Fourier transform-infrared spectrosocopy(FT-IR) and ultraviolet-visible(UV-Vis) *** spherical morphology of particles with an average diameter of 100 nm was observed by scartning electron microscopy(SEm).The polymeric materials were used for recovery of [Eu]from synthetic *** nanoparticles show excellent chelation capacity to trap rare-earth ions,because they recover more than 85% of [Eu] at pH of *** images of SEm after extraction process show arrays between particles with larger average particle sizes to 1.5 *** addition,the particles have a good stripping capacity,exceeding 50% of it,maintaining their homogeneity in morphology and good stability in dispersion for the recovery and stripping processes.A pseudo-second model order is obtained for the extraction and stripping processes while the best results of stripping process are obtained at pH of6.

关键词： Chelating effect Emulsion polymerization Extraction process Rare earths Stripping process [Eu]recovery