检索结果-南通市图书馆

Influence of sintering time on microstructure and properties of hot oscillatory pressing sintered W–Cu refractory alloys

引用

Tungsten 2024年第2期6卷 323-332页

作者： zi-qian Wu Wei Zhao Ka Gao Shi-hao Du Qing-Quan Kong De-Jian Sun Yang Gao School of Materials Science and Engineering Zhengzhou University of AeronauticsZhengzhou 450015China School of Mechanical Engineering University of Shanghai for Science and TechnologyShanghai 200093China Department of General Medicine Changhai HospitalShanghai 200000China Hubei Key Laboratory of Mechanical Transmission and Manufacturing Engineering Wuhan University of Science and TechnologyWuhan 430081China Sichuan Province Engineering Technology Research Center of Powder Metallurgy Chengdu UniversityChengdu 610106China

W–Cu refractory alloys are widely used in aerospace,aviation,electronics,power,and other fi elds.However,because of its large melting point diff erence between alloy elements,the conventional powder metallurgy method required a long time of high temperature sintering is very likely to cause low density and abnormal grain size growth.Therefore,90W-10Cu refractory alloys were successfully prepared by hot oscillatory pressing(HOP)under diff erent sintering time in this work.Then the infl uence of sintering time on the microstructure,grain size,density,Vickers hardness,room-tensile property,and electrical conductivity of the W–Cu refractory alloy was systematically invested.The results showed that during the short sintering time(30–90 min),the density,Vickers hardness,tensile strength,and electrical conductivity of the W–Cu refractory alloy increased signifi cantly to 98.7%,163.29 HV 30,507.3 MPa,and 14.2%International Annealed Copper Standard with the sintering time increasing,respectively,while its grain size showed no obvious change.When the sintering time further increased to 120 min,the density was basically consistent with the sintering time of 90 min.Nevertheless,the prolonged high temperature sintering resulted in the grain growth of the samples,which caused the deterioration of the Vickers hardness,room-tensile strength,and conductivity properties of the W–Cu refractory alloy.At the same sintering time,the density,Vickers hardness,and electrical conductivity of the HOP sintered W–Cu refractory alloy were signifi cantly higher than those of the HP sintered sample.It was indicated that high density,fi ne-grain,and excellent properties W–Cu refractory alloys could be prepared by hot oscillatory pressing under appropriate sintering time.

关键词： W–Cu refractory alloy Hot oscillatory pressing Sintering time Microstructure Property

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Ferritinophagy: A new idea for liver diseases regulated by ferroptosis

引用

Hepatobiliary & Pancreatic Diseases International 2024年第2期23卷 160-170页

作者： zi-Bing qian Jun-Feng Li Wan-Yuan Xiong Xiao-Rong Mao The First Clinical Medical College of Lanzhou University Lanzhou 730000China Institute of Infectious Diseases The First Hospital of Lanzhou UniversityLanzhou 730000China Department of Infectious Disease The First Hospital of Lanzhou UniversityLanzhou 730000China

Background:The discovery of regulatory cell death has led to a breakthrough in the therapeutic field.Various forms of cell death,such as necrosis,apoptosis,pyroptosis,autophagy,and ferroptosis,play an important role in the development of liver diseases.In general,more than one form of cell death pathways is responsible for the disease state.Therefore,it is particularly important to study the regulation and interaction of various cell death forms in liver diseases.Data sources:We performed a PubMed search up to November 2022 with the following keywords:ferritinophagy,ferroptosis,and liver disease.We also used terms such as signal path,inducer,and inhibitor to supplement the query results.Results:This review summarized the basic characteristics of ferritinophagy and ferroptosis and the regulation of ferroptosis by ferritinophagy and reviewed the key targets and treatment strategies of ferroptosis in different liver diseases.Conclusions:Ferritinophagy is a potential therapeutic target in ferroptosis-related liver diseases.

关键词： Ferritinophagy Ferroptosis Liver disease

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Remote copper-catalyzed enantioselective substitution of yne-thiophene carbonates

引用

Science China Chemistry 2024年第4期67卷 1175-1180页

作者： hao-Dong qian Xiang Li Tingrui Yin Wei-Feng qian Chunhui Zhao Cuiju Zhu hao Xu CCNU-uOttawa Joint Research Centre Key Laboratory of Pesticides&Chemical Biology of Ministry of EducationInternational Joint Research Center for Intelligent Biosensing Technology and HealthCollege of ChemistryCentral China Normal UniversityWuhan 430079China

Here,we describe a strategy for the copper-catalyzed asymmetric heteroarylation of yne-thiophene carbonates with indoles via remote substitution.The key to the success of this strategy lies in the design of the alkynyl group at the ortho-position of the heterocycle thiophene,enabling the formation of a triarylmethane moiety via very remote substitution.Thus,the concept of remote copper-catalyzed asymmetric transformation extends not only to yne-allylic esters but also to yne-aryl esters.The reaction readily provides a diverse array of chiral triarylmethanes with high efficiency,enantioselectivity,and excellent functional group compatibility.Moreover,facile follow-up transformations underscore their potential utility in the synthesis of various enantioenriched building blocks.Preliminary mechanistic studies support the plausibility of the remote substitution pathway.

关键词： remote substitution copper catalyst asymmetric catalysis triaryl methanes

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Antiviral treatment standards for hepatitis B:An urgent need for expansion

引用

World Journal of Gastroenterology 2024年第4期30卷 418-420页

作者： zi-Hong Bao Zhi-Kun Dai hao-Xian Tang Department of Infectious Diseases The First Affiliated Hospital of Shantou University Medical CollegeShantou 515041Guangdong ProvinceChina Medical College Shantou University Medical CollegeShantou 515041Guangdong ProvinceChina Department of Cardiology The First Affiliated Hospital of Shantou University Medical CollegeShantou 515041Guangdong ProvinceChina

The present letter to the editor is related to the review with the title“Past,present,and future of long-term treatment for hepatitis B virus.”Chronic hepatitis B(CHB)represents an important and pressing public health concern.Timely identification and effective antiviral therapy hold the potential to reduce liver-related mortality attributable to chronic infection with hepatitis B virus(HBV)substantially.However,the current global treatment rates for CHB remain conspicuously low,with the excessively stringent treatment criteria advocated by national CHB guidelines being a contributing factor to these low rates.Nevertheless,recent strides in comprehending this malady and the emergence of novel antiviral agents prompt the imperative re-evaluation of treatment standards to extend the sphere of potential beneficiaries.An impending need arises for a novel paradigm for the classification of patients with CHB,the expansion of antiviral treatment eligibility for HBV-infected individuals,and even the streamlining of the diagnostic process for CHB to amplify cost-effectiveness and augment survival prospects.

关键词： Hepatitis B virus Chronic hepatitis B Antiviral treatment criteria Serum alanine aminotransferase Liver-related mortality Letter to the Editor

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Enhancing force sensing in a squeezed optomechanical system with quantum nondemolition measurement

引用

Communications in Theoretical Physics 2024年第1期76卷 49-60页

作者： Shi-Lei Chao zi-hao Li Xin-You Lü School of Physics Huazhong University of Science and Technology430074 WuhanChina

A theoretical scheme is proposed to enhance the sensitivity of force sensors with quantum nondemolition measurement(QND)in an optomechanical setup assisted by four-tone optical driving and an optical parametric amplifier(OPA).With the help of special drive,the system can be simplified as the typical type of QND for force sensing,so that the backaction noise can be evaded to surpass the standard quantum limit.Besides,the added noise can be suppressed owing to the modified optical susceptibility resulting from the OPA.By introducing two oscillators coupling with two charged bodies respectively,the signal can be enhanced with the nonlinearity caused by Coulomb interaction,while the noise presents an exponential decrease.Moreover,considering the homodyne detection effect,the range of system parameters and frequency bands will be broadened.The present investigation may provide a route toward simultaneously evading backaction noise,reducing the mechanical thermal noise,and enhancing the external signal,which can be an alternative design for sensitive devices.

关键词： force sensing optical parametric amplifier quantum non-demolition measurement optomechanical system

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Highly efficient photocatalytic conversion of CO_(2) into CH_(4) over Cu single atom promoted heterojunction:The effect of uplifted d-band center

引用

Chinese Chemical Letters 2024年第2期35卷 484-488页

作者： hao Zhang qian Liu Zhurui Shen School of Materials Science and Engineering Nankai UniversityTianjin 300350China

Photoreduction of CO_(2) to solar fuels has caused great interest,but suffers from low catalytic efficiency and poor selectivity.Herein,we designed a S-scheme heterojunction(Cu-TiO_(2)/WO_(3))with Cu single atom to significantly boost the photoreduction of CO_(2).Notably,the developed Cu-TiO_(2)/WO_(3) achieved the solardriven conversion of CO_(2) to CH_(4) with an evolution rate of 98.69μmol g^(−1) h^(−1),and the electron selectivity of CH_(4) reached 88.5%.The yield was much higher than those of pristine WO_(3),TiO_(2)/WO_(3) and Cu-TiO_(2) samples.Experimental and theoretical analysis suggested that the S-scheme heterojunction accelerated charge migration and inhibited the recombination of electron-hole pairs.Importantly,the charge separation effect of the heterojunction meliorated the position of the d-band.The uplifted d-band centers of Cu and Ti on Cu-TiO_(2)/WO_(3) not only improved the electron interaction between Cu single atoms and substrate-TiO_(2),accelerated the adsorption and activation of CO_(2) on the active sites of Cu single atom,but also optimized the Gibbs free energies of CH 4 formation pathway,leading to excellent selectivity toward CH_(4).This work provides new insights into the design of photocatalyst systems with high photocatalytic performance.

关键词： Cu single atom Heterojunction CO_(2)photoreduction d-band center DFT

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Nonreciprocal generation of Schrodinger cat state induced by topology

引用

Science China(Physics,Mechanics & Astronomy) 2024年第4期67卷 23-30页

作者： zi-hao Li Li-Li Zheng Ying Wu Xin-You Lü School of Physics and Institute for Quantum Science and Engineering Huazhong University of Science and Technologyand Wuhan Institute of Quantum TechnologyWuhan 430074China Key Laboratory of Optoelectronic Chemical Materials and Devices of Ministry of Education Jianghan UniversityWuhan 430074China

The Schrodinger cat state produced differently in two directions is anticipated to be a critical quantum resource in quantum information technologies.By exploring the interplay between quantum nonreciprocity and topology in a one-dimensional microcavity array,we obtain the Schrodinger cat state(a pure quantum state)in a chosen direction at the edge cavity,whereas a classical state in the other direction.This nonreciprocal generation of the cat state originates from the topologically protected chiralitymode excitation in the nontrivial phase,but in the trivial phase,the nonreciprocal generation of cat state vanishes.Thus,our proposal is switchable by tuning the parameters so that a topological phase transition occurs.Moreover,the obtained cat state has nonreciprocal high fidelity,nonclassicality,and quantum coherence,which are sufficient to be used in various one-way quantum technologies,e.g.,invisible quantum sensing,noise-tolerant quantum computing,and chiral quantum networks.Our work provides a general approach to control quantum nonreciprocities with the topological effect,which substantially broadens the fields of nonreciprocal photonics and topological physics.

关键词： Schr?dinger cat state nonreciprocity topology

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Probabilistic seismic inversion based on physics-guided deep mixture density network

引用

Petroleum Science 2024年第3期21卷 1611-1631页

作者： qian-hao Sun Zhao-Yun Zong Xin Li National Key Laboratory of Deep Oil and Gas China University of Petroleum(East China) Laoshan Laboratory CNOOC Research Institute Ltd.

Deterministic inversion based on deep learning has been widely utilized in model parameters estimation.Constrained by logging data, seismic data, wavelet and modeling operator, deterministic inversion based on deep learning can establish nonlinear relationships between seismic data and model parameters.However, seismic data lacks low-frequency and contains noise, which increases the non-uniqueness of the solutions. The conventional inversion method based on deep learning can only establish the deterministic relationship between seismic data and parameters, and cannot quantify the uncertainty of inversion. In order to quickly quantify the uncertainty, a physics-guided deep mixture density network(PG-DMDN) is established by combining the mixture density network(MDN) with the deep neural network(DNN). Compared with Bayesian neural network(BNN) and network dropout, PG-DMDN has lower computing cost and shorter training time. A low-frequency model is introduced in the training process of the network to help the network learn the nonlinear relationship between narrowband seismic data and low-frequency impedance. In addition, the block constraints are added to the PG-DMDN framework to improve the horizontal continuity of the inversion results. To illustrate the benefits of proposed method, the PG-DMDN is compared with existing semi-supervised inversion method. Four synthetic data examples of Marmousi II model are utilized to quantify the influence of forward modeling part, low-frequency model, noise and the pseudo-wells number on inversion results, and prove the feasibility and stability of the proposed method. In addition, the robustness and generality of the proposed method are verified by the field seismic data.

关键词： Deep learning Probabilistic inversion Physics-guided Deep mixture density network

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Janus Quasi‑Solid Electrolyte Membranes with Asymmetric Porous Structure for High‑Performance Lithium‑Metal Batteries

引用

Nano-Micro Letters 2024年第6期16卷 221-232页

作者： Zerui Chen Wei Zhao qian Liu Yifei Xu Qinghe Wang Jinmin Lin hao Bin Wu Institute for Composites Science Innovation(InCSI)and State Key Laboratory of Silicon and Advanced Semiconductor Materials School of Materials Science and EngineeringZhejiang UniversityHangzhou 310027People’s Republic of China

Quasi-solid electrolytes(QSEs)based on nanoporous materials are promising candidates to construct high-performance Limetal batteries(LMBs).However,simultaneously boosting the ionic conductivity(σ)and lithium-ion transference number(t^(+)) of liquid electrolyte confined in porous matrix remains challenging.Herein,we report a novel Janus MOFLi/MSLi QSEs with asymmetric porous structure to inherit the benefits of both mesoporous and microporous hosts.This Janus QSE composed of mesoporous silica and microporous MOF exhibits a neat Li^(+) conductivity of 1.5.10^(–4)S cm^(−1) with t^(+) of 0.71.A partially de-solvated structure and preference distribution of Li^(+)near the Lewis base O atoms were depicted by MD simulations.Meanwhile,the nanoporous structure enabled efficient ion flux regulation,promoting the homogenous deposition of Li^(+).When incorporated in Li||Cu cells,the MOFLi/MSLi QSEs demonstrated a high Coulombic efficiency of 98.1%,surpassing that of liquid electrolytes(96.3%).Additionally,NCM 622||Li batteries equipped with MOFLi/MSLi QSEs exhibited promising rate performance and could operate stably for over 200 cycles at 1 C.These results highlight the potential of Janus MOFLi/MSLi QSEs as promising candidates for next-generation LMBs.

关键词： Metal-organic frameworks Mesoporous silicas Quasi-solid electrolytes Janus structure Lithium-metal battery

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Experimental research on the launching system of auxiliary charge with filter cartridge structure

引用

Defence Technology（防务技术） 2024年第1期31卷 41-48页

作者： zi-Jun Chen Ze He Hong-hao Ma Lu-Qing Wang Zhao-Wu Shen CAS Key Laboratory of Mechanical Behavior and Design of Materials Department of Modern MechanicsUniversity of Science and Technology of ChinaHefeiAnhui230027PR China State Key Laboratory of Fire Science University of Science and Technology of ChinaHefeiAnhui230026PR China

A launching system with a filter cartridge structure was proposed to improve the muzzle velocity of the projectile.The combustion chamber of the launching system is divided into two fixed chambers,one is located in the breech chamber,and the other is arranged in the barrel.The breech chamber charge was ignited first,and the charges in the auxiliary chambers were ignited by the high-temperature,highpressure combustible gas trailing the projectile.In this way,the combustible gas in the auxiliary chambers could compensate for the pressure drop caused by the movement of the projectile.The proposed device features the advantage of launching a projectile with high muzzle velocity without exceeding the maximum pressure in the chamber.In order to obtain some internal ballistic characteristics of the launch system,some critical structure,such as the length of the filter cartridge auxiliary charge,the combustion degree of the propellant in the chamber,and the length of the barrel,are discussed.The experimental results show that with the increased auxiliary charge length,a pressure plateau or even a secondary peak pressure can be formed,which is less than the peak pressure.The projectile velocity increased by 23.57%,14.64%,and 7.65%when the diaphragm thickness was 0 mm,1 mm,and2 mm,respectively.The muzzle velocity of the projectile can be increased by 13.42%by increasing the length of the barrel.Under the same charge condition,with the increase of barrel length,the energy utilization rate of propellant increases by 28.64%.

关键词： Interior ballistics Charge structures Launch system Charge design

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：