检索结果-南通市图书馆

Solid State Synthesis and Thermoelectric Properties of Mg-Si-Ge System

在线全文

学校读者我要写书评

暂无评论

Journal of Materials Science & Technology 2005年第5期21卷 618-622页

作者： Renbo SONG Yazheng LIU tatsuhiko aizawa School of Materials Science and Engineering University of Science and Technology Beijing Beijing 100083 China Center for Collaborative Research The University of Tokyo Komaba 4-6-1 Meguro-ku Tokyo 153-8904 Japan

Thermoelectric materials, Mg2Si1-xGex （x=0, 0.2, 0.4, 0.6, 0.8, 1）, have been prepared by bulk mechanical alloying （BMA） and hot pressing （HP）. The electrical conductivity, Seebeck coefficient and thermal conductivity were measured from room temperature up to about 700 K. The electrical conductivity of all the samples increases with increasing temperature, while the Seebeck coefficient and thermal conductivity decrease with increasing temperature. Mg2Si and Mg2Si0.8Ge0.2 possess negative type of conductivity, while for other compounds it is positive. At the same time, the effect of hot processing condition on thermoelectric properties was also investigated. The maximum figure of merit of Mg2Si0.6Ge0.4 was obtained with the processing parameter of BMA at 600 cycles and hot pressing at 773 K and i GPa for i h.

关键词： Solid-state synthesis Mg2Si1-xGex Bulk mechanical alloying Thermoelectric Hot pressing

Thermoelectric Properties of Mg_2Si_(1-x)Sn_x Synthesized by Bulk Mechanical Alloying

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Aeronautics 2006年第B12期19卷 134-138页

作者： SONG Ren-bo LIU Ya-zheng tatsuhiko aizawa School of Material Science and Engineering University of Science and Technology Beijing Beijing 100083 China Jayram Office University of Toronto Shanghai International Building 6F 1-24-12 Shinkawa Chuo-ku Tokyo 104-0033 Japan

Bulk mechanical alloying （BMA） has been successfully applied to solid-state synthesis of p-type and n-type thermoelectric materials Mg2Si1-xSnx （x = 0, 0.2, 0.4, 0.6, 0.8, 1） from element-powders at the room temperature in a relatively short time. The electrical conductivity, the Seebeck coefficient and the thermal conductivity of the Mg2Si1-xSnx are quite sensitive to the x-content. With the x-content rising, the electrical conductivity increases. When x = 0.6, it reaches the lowest and Mg2Si shows an n-type of semi-conducting However, when x = 0.2 and T 〉525 K, the Seebeck coefficient of the samples will change the opposite way. While x≥0.4, the samples present a p-type of semi-conducting. The figure of merit, Z of Mg2Si1-xSnx will be obtained in the range from 300 K to 700 K. When x = 0.6, Z proves to be higher than that of other samples at 300 K≤ T≤650 K.

关键词： solid-state synthesis thermoelectric bulk mechanical alloying Mg2Si1-xSnx

Dry Machining Tool Design via Chlorine Ion Implantation

在线全文

学校读者我要写书评

暂无评论

材料热处理学报 2004年第05B期25卷 879-882页

作者： tatsuhiko aizawa Atsushi Mitsuo Shigeo Yamamoto Shinji Muraishi Taro Sumitomo Center for Collaborate Research University of Tokyo Tokyo JapanTokyo Metropolitan Industrial Research Institute Tokyo JapanTokyo Metropolitan Industrial Research Institute Tokyo JapanDepartment of Materials Science Technology Tokyo Institute of Technology Tokyo JapanCenter for Collaborate Research University of Tokyo Tokyo Japan

Dry machining has become a key issue to significantly reduce the wastes of used lubricants and cleaning agents and to improve the environmental consciousness for medical and food applications of special tooling. Since the tools and metallic works are in direct contact in dry, severe adhesive wear and oxidation are thought to occur even at the presence of hard protective coatings. Self-lubrication mechanism with use of lubricous oxide films is found to be effective for dry machining. Through the chlorine ion implantation to tools, titanium base oxides are in-situ formed on the tool surface. This oxide deforms elasto-plastically so that both friction coefficient and wear volume are reduced even in the high-speed cutting.

关键词：氯离子注入自动润滑 TiN涂层 TiCN涂层干机械加工

THREE DIMENSIONAL ELASTO-PLASTIC CONTACT BOUNDARY ELEMENT ANALYSIS FOR ROLLING WITH CONSIDERATION OF FRICTION

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Mechanical Engineering 1998年第1期11卷 63-69页

作者： Xiao, Hong Chen, Yiming Shen, Guangxian aizawa, tatsuhiko Kihara, Junji Yanshan Univ China

The boundary element method in framework is given to evaluate three dimensional frictional contact problems. Elasto plastic material behavior is taken into account by mean of an initial stress formulation and Von Mises yield criterion. The amount of tangential traction at contact surface is limited by Coulomb's friction law and constant shear rule. From some numerical results of a plate rolling problem, it is demonstrated here that the BEM can be used to efficiently and accurately analyze this class of forming problems.

关键词： Strip Rolling Boundary element method Elasto plasticity Contact Friction

Plasma Nitriding-Assisted Printing of Stainless Steel Punches for Micro-piercing Process

在线全文

学校读者我要写书评

暂无评论

Journal of Mechanics Engineering and Automation 2017年第1期7卷 1-11页

作者： tatsuhiko aizawa Tomomi Shiratori Department of Engineering and Design Shibaura Institute of Technology 3-9-14 Shibaura Minato-City Tokyo 108-8548 Japan R & D Center Komatsu Seiki Kosakusho Co. Ltd. Shiga-Kuwahara Ohaza Suwa-City Nagano 942-2 Japan

MEMS （micro-electric-mechanical-system） required for miniature, thin mechanical parts as a structural member; e.g., the miniature pumping system consisted of ten to twelve thin metallic plates before joining. At present, those thin shaped sheets were fabricated by the chemical etching. Their geometric inaccuracy as well as long leading time often became an engineering issue. Micro-piercing process was expected to make mass production of thin sheet products with complex and accurate geometry for much shorter leading time once the die for this micro-piercing was built in. In the present paper, a new plasma nitriding-assisted printing was proposed as an automatic production line to fabricate the micro-piercing punch. After preparation of CAD-data of the punch head, its two dimensional geometry was ink-jet printed directly on the AISI420 stainless steel die-substrate. The unprinted surface area was only plasma nitrided at 693 K for 14.4 ks to transform this two dimensional micro-pattern to the three dimensional hardness distribution in the AISI420 substrate. Through the mechanical removal of ink-jet printed area, the flat punch head with sharp edge comers was fabricated in much shorter duration time than the end-milling. SEM-EDX, surface profiling measurement as well as micro-hardness testing were employed to describe each step in the above plasma printing. The thin MEMS stainless steel part with a micro-pendulum as well as three S-letter shaped springs was taken for an example to describe this automatic production procedure of plasma printing from the CAD data mining to the micro-piercing punch finishing.

关键词： Plasma printing ink-jet printing plasma nitriding sand-blasting micro-piercing stainless steel punch.

High Density Plasma Nitriding of Al-Cu Alloys for Automotive Parts

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Physical Science and Application 2014年第4期4卷 255-261页

作者： tatsuhiko aizawa Shinji Muraishi Yoshio Sugita Department of Engineering and Design Shibaura Institute of Technology Tokyo 108-8548 Japan Department of Materials Science and Engineering Tokyo Institute of Technology Tokyo Japan YS-Electrical Industry Co. Ltd. Koufu 400-0043 Japan

Duralumin alloys have been utilized as structural components and parts for aircrafts, train-cars and so forth. Their high specific strength was attractive to those applications; however, their little corrosion resistance and low wear endurance became a fatal demerit in practical applications. In order to overcome these issues of high strength aluminum alloys, high density plasma nitriding is proposed as an effective surface treatment for duralumin. This process has a capability to control the RF- and DC-plasmas independently for nitriding. This enables us to temporally control and describe the plasma state by in-situ plasma diagnosis. This plasma diagnosis was instrumented to search for optimum processing condition to plasma nitriding the duralumin alloys of type A2011. Both type A2011 aluminum alloy plates and pipes were employed to describe the inner nitriding behavior for hardening the duralumin alloys by the present plasma nitriding.

关键词： Duralumin alloys A2011 high density plasma nitrding AIN precipitation hardening plates pipes heat sink.