检索结果-南通市图书馆

阿哈湖深层水中微生物和硫酸还原菌数量及群落结构空间变化

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

生态学杂志 2007年第11期26卷 1898-1900页

作者：王明义梁小兵 tae seok ahn In Seon Kim Jong Hyun Nam 魏中青张伟中国科学院地球化学研究所环境地球化学国家重点实验室 Department of Environmental Science Kangwon National University

采用荧光原位杂交法分析了贵州阿哈湖深层水环境中总微生物、真细菌和硫酸盐还原菌数量。结果表明:该湖水中微生物总量为1.6×107个.L-1,真细菌占微生物总量的52.9%,且微生物总量和真细菌数量垂直变化无明显差异。随着水体深度的增加,... 详细信息

采用荧光原位杂交法分析了贵州阿哈湖深层水环境中总微生物、真细菌和硫酸盐还原菌数量。结果表明:该湖水中微生物总量为1.6×107个.L-1,真细菌占微生物总量的52.9%,且微生物总量和真细菌数量垂直变化无明显差异。随着水体深度的增加,活性微生物数量增加,且微生物的群落结构更加复杂。阿哈湖深层水体中有一定数量的硫酸盐还原菌存在。

关键词：水环境荧光原位杂交真细菌硫酸盐还原菌空间变化

Sulfur species variation controlled by sulfate reducing bacteria (SRB) in sediments of Lake Erhai

在线全文

学校读者我要写书评

暂无评论

Acta Geochimica 2006年第S1期 147-147页

作者： tae seok ahn Department of Envionmental Science Kangwang National University Chunchon Korea

Prominent cycling reversibility and kinetics enabled by CaTiO3 protective layer on Zn metal for aqueous Zn-ion batteries

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Journal of Energy Chemistry 2025年第1期100卷 245-258页

作者： Gaeun Lee Yong Nam ahn Seongjoon So Chanwoo Park Jong-Seong Bae taehyun Park Il tae Kim Jaehyun Hur School of Chemical Biological and Battery Engineering Gachon University Seongnam Busan Center Korea Basic Science Institute

Aqueous Zn-ion batteries （AZIBs） have received considerable attention owing to their various advantages such as safety,low cost,simple battery assembly conditions,and high ionic ***,they still suffer from serious problems,including uncontrollable dendrite growth,corrosion,hydrogen evolution reaction （HER） from water decomposition,electrode passivation,and unexpected *** creation of a uniform artificial nanocrystal layer on the Zn anode surface is a promising strategy for resolving these ***,we propose the use of a perovskite CaTiO3（CTO） protective layer on Zn（CTO@Zn） as a promising approach for improving the performance of *** CTO artificial layer provides an efficient pathway for Zn ion diffusion towards the Zn metal because of the high dielectric constant （εr=180） and ferroelectric characteristics that enable the alignment of dipole moments and redistribute the Zn2+ions in the CTO *** avoiding the direct contact of the Zn anode with the electrolyte solution,the uneven dendrite growth,corrosion,parasitic side reactions,and HER are mitigated,while CTO retains its mechanical and chemical robustness during ***,CTO@Zn demonstrates an improved lifespan in a symmetric cell configuration compared with bare ***@Zn shows steady overpotential （～68 m V） for 1500 h at 1 mA cm-2/0.5 mA h cm-2,excelling bare ***,when paired with the V2O5-C cathode,the CTO@Zn//V2O5-C full battery delivers 148.4 mA h g-1（based on the mass of the cathode） after 300 *** study provides new insights into Zn metal anodes and the development of high-performance AZIBs.

关键词： Artificial layer Dielectric constant Zn metal anode Zinc aqueous battery

Sulfur species variation controlled by sulfate reducing bacteria (SRB) in sediments of Lake Erhai

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Chinese Journal Of Geochemistry 2006年第B8期25卷 147-147页

作者： Xiaobing LIANG tae seok ahn Mingyi WANG Youzhi ZHAO Institute of Geochemistry Chinese Academy of Sciences Guiyang 550002 China Department of Envionmental Science Kangwang National University Chunchon Korea

DC Motor Speed Regulator via Active Damping Injection and Angular Acceleration Estimation Techniques

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

IEEE/CAA Journal of Automatica Sinica 2021年第3期8卷 641-647页

作者： seok-Kyoon Kim Choon Ki ahn Department of Creative Convergence Engineering Hanbat National UniversityDaejeon 341-58Republic of Korea School of Electrical Engineering Korea UniversitySeoul 136-701Republic of Korea

This paper suggests a novel model-based nonlinear DC motor speed regulator without the use of a current *** current dynamics,machine parameters and mismatched load variations are *** proposed controller is designed to include an active damping term that regulates the motor speed in accordance with the first-order low-pass filter dynamics through the pole-zero ***,the angular acceleration and its reference are obtained from simple first-order estimators using only the speed *** effectiveness is experimentally verified using hardware comprising the QUBEServo2,myRIO-1900,and LabVIEW.

关键词： Active damping injection angular acceleration estimator DC motor(DCM) speed regulation

Influence of Processing Parameters on the Mechanical Properties of a Plasma Radical Nitrided SCM440 Steel

在线全文

学校读者我要写书评

暂无评论

Journal of Materials Science & Technology 2008年第3期24卷 356-358页

作者： seok-Hwan ahn Insup Lee School of Mechanical Engineering Pukyong National University Department of Materials and Metallurgical Engineering Dongeui University

Plasma radical nitriding was performed to harden the surface of SCM440 steel for 1-10 h at temperature range of 450-550℃. This process involved the use of NH3 gas instead of N2 gas employed for the well-established plasma nitriding method. No compound layer was formed during this process except the experiment carried out at 500℃ for 10 h. The main phase produced in the diffusion zone was identified to be γ＇-Fe4（N, C）. A diffusion depth increased with increasing treatment temperature and time （up to about 250 μm）. The surface hardness of radical nitrided layer was about two times higher than that of the untreated surface. The tensile test was carried out to estimate the mechanical properties of surface-hardened SCM440 steel prepared at various plasma radical nitriding treatment time and temperature. The influence of radical nitriding treatment on the tensile strength of the specimen was found to be insignificant. The highest value of the ultimate tensile strength was obtained in the experiment carried out at 500℃ for 1 h. However, the elongation was greatly affected by the radical nitriding processing parameters. The maximum value of elongation, which is equal to about 18.1%, was also obtained under the condition of 500℃ for 1 h.

关键词： Plasma radical nitriding Tensile strength Elongation Surface hardness Diffusion depth Compound layer

The Characteristics of CLHS Driving for High Luminance Efficiency in AC PDP

在线全文

学校读者我要写书评

暂无评论

Plasma Science and Technology 2016年第11期18卷 1116-1122页

作者： Gun-Su KIM Chi-Hyung ahn seok-Hyun LEE Department of Electrical and Electronic Engineering Youngsan UniversityYangsanGyeongnam 50510Korea Korea Railroad Research Institute Uiwang Gyeonggi 16105Korea School of Electrical Engineering Inha UniversityIncheon 22212Korea

This paper proposes a CLHS （Capacitor Less Half Sustain） driving method that is applied to a long gap panel to reduce the power consumption. In order to reduce the power consumption in moving images, the luminous efficiency should be improved at the low discharge load （〈25%）. The weight of reactive power consumption tends to increase as the low discharge load decreases. Thus, it is very important to improve the luminous efficiency at low discharge load. It is well known that a long gap panel improves the luminance and the luminous efficiency but it is very difficult to drive the panel due to high driving voltage. It is confirmed that the main factors which cause a long gap panel to increase the minimum driving voltages are not only a long discharge gap but also self-erasing discharge. Self-erasing discharge is generated between the address and sustain electrodes in a sustain period. The CLHS driving method can reduce the reactive power consumption in a sustain period because energy recovery capacitors were removed in the sustain circuit. The CLHS driving method can reduce the minimum driving voltage of the long gap panel because the self-erasing discharge was prevented. When the CLHS driving method was applied to the panel with an ITO gap of 100 μm, Vs and VA minimum voltages are reduced by about 9 V and 12 V compared with those of the normal driving method. The luminance and the luminous efficiency also increased by about 24.3% and 33.3% at the discharge load of 4% compared with those at the normal condition.

关键词： PDP plasma long gap CLHS

A Study of the Influence of Air-knife Tilting on Coating Thickness in Hot-dip Galvanizing

在线全文

学校读者我要写书评

暂无评论

Journal of Thermal Science 2009年第3期18卷 262-267页

作者： tae-seok CHO Young-Doo KWON Soon-Bum KWON School of Mechanical Engineering Kyungpook National University

Gas wiping is a decisive operation in hot-dip galvanizing process. In special, it has a crucial influence on the thickness and uniformity in coating film, but may be subsequently responsible for the problem of splashing. The progress of industry demands continuously the reduction of production costs which may relate directly with the increase of coating speed, and the speed up of coating results in the increase of stagnation pressure in gas wiping system in final. It is known that the increase of stagnation pressure may accompany a harmful problem of splashing in general. Together with these, also, from the view point of energy consumption, it is necessary to design a nozzle optimally. And there is known that the downward tilting of nozzle using in air knife system is effective to prevent in somewhat the harmful problem of splashing. In these connections, first, we design a nozzle with constant expansion rate. Next, for the case of actual coating conditions in field, the effects of tilting of the constant expansion rate nozzle are investigated by numerical analysis. Under the present numerical conditions, it was turned out that the nozzle of constant expansion rate of p = having a downward jet angle of 5^0 is the most effective to diminish the onset of splashing, while the influence of small tilting of the nozzle on impinging wall pres- sure itself is not so large.

关键词： Air-knife Constant expansion rate nozzle Impinging pressure Wall shear stress Hot-dip galvanizing Coating thickness Splashing

Combustion Characteristics of Solid Refuse Fuels from Different Waste Sources

在线全文

学校读者我要写书评

暂无评论

Journal of Renewable Materials 2020年第7期8卷 789-799页

作者： Jong Seong Chae seok Wan Kim tae In Ohm Department of Civil and Environmental Engineering Hanbat National UniversityDaejeon34158Korea Department of Fire and Environmental Safety Daegu Haany UniversityDaegu38610Korea

In the production(as co-fuel or alone)of solid refuse fuel(SRF),knowledge about the characteristics of the raw materials is required for an ecofriendly and effective combustion *** are commonly produced by drying combustible waste and removing incombustible matter,resulting in a higher combustibility as compared to the original ***,the characteristics of SRFs may highly vary depending on where and from which materials they were ***,we investigated the characteristics of various SRFs using thermogravimetric analysis(TGA).As a TGA sample is commonly small,on the scale of milligrams,and,unlike homogeneous fuels,SRFs are heterogeneous,individual SRF samples analysed with this method may not represent the bulk material,and sample properties may vary significantly between ***,we further performed combustion experiments using a small-scale combustor and sample sizes from 1 to 10 *** optimise SRF combustor design and determine the SRF characteristics,proximate,elemental,heating value,TG,and differential thermogravimetric analyses were conducted,and weight losses and gas concentrations at different temperatures were measured upon *** lower heating values of the three analysed SRFs were 20,976,16,873,and 19,762 kJ/kg,and their Cl contents were 0.89,0.95,and 1.27 wt.%(legal criterion[Cl]<2.0 wt.%).TGA and small combustor experiments showed that complete weight loss was achieved below 500°***,CO was detected until 620°C.

关键词： Solid refuse fuel small-scale combustor thermogravimetric analysis waste gas concentration