检索结果-南通市图书馆

Frontiers of Structural and Civil Engineering 2024年第7期18卷 1117-1133页

作者： Pengfei dou Hao LIU Chengshun XU Jinting WANG Yilong SUN Xiuli DU Department of Hydraulic Engineering Tsinghua UniversityBeijing 100084China Key Laboratory of Urban Security and Disaster Engineering of the Ministry of Education Beijing University of TechnologyBeijing 100124China

This study investigates the seismic response and failure mode of a pile-structure system in a liquefiable site by employing a numerical simulation model combined with the shaking-table results of a soil-pile-structure dynamic *** pile and soil responses obtained from the numerical simulations agreed well with the experimental *** slopes of the dynamic shear-stress-shear-strain hysteretic curves at different positions also exhibited a decreasing trend,indicating that the shear strength of the soil in all parts of the foundation *** peak acceleration of the soil and pile was not clearly amplified in the saturated sand layer but appeared to be amplified in the top *** maximum bending moments appeared in the middle and lower parts of the pile shaft;however,the shear forces at the corresponding positions were not *** can be observed from the deformation mode of the pile-group foundation that a typical bending failure is caused by an excessive bending moment in the middle of the pile shaft if the link between the pile top and cap is articulated,and sufficient attention should be paid to the bending failure in the middle of the pile shaft.

关键词： numerical simulation soil liquefaction pile foundation shaking-table experiment seismic responses failure model

Enrichment and reconfiguration of titanium-bearing phase in vortex smelting reduction process of vanadium-titanium magnetite

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第7期31卷 1582-1589页

作者： Yong-chao Han Zhi-he dou Rui Zhang Ting-an Zhang Shuai Fang Key Laboratory for Ecological Metallurgy of Multimetallic Ores(Ministry of Education) Shenyang 110819LiaoningChina School of Metallurgy Northeastern UniversityShenyang 110819LiaoningChina

To comprehensively utilize the low-iron high-vanadium-titanium magnetite,a new method of vortex smelting reduction of vanadium-titanium magnetite was proposed,and the enrichment and reconstitution regularity of Ti-bearing phases in the slag was investigated through X-ray fluorescence spectrometry,X-ray photoelectron spectroscopy,X-ray diffraction analysis,and optical *** phase diagram revealed that the preferential crystallization of MgTi_(2)O_(5) can be achieved by adjusting the CaO,MgO,and TiO_(2) contents of *** predominant Ti-bearing phases in the slag obtained from the reduction process are MgxTi_(3_x)O_(5)(0≤x≤1)and CaTiO_(3).FeTiO_(3) is present at carbon-iron ratio(CR)=1.3,while MgTi_(2)O4 and TiC are formed at CR=*** enrichment of TiO_(2) in the slag increases first and then decreases as the CR increases,and at CR=1.1,the enrichment of TiO_(2) in the slag reaches 51.3 wt.%.Additionally,the concentrations of MgxTi_(3_x)O_(5)(0≤x≤1)and CaTiO_(3) in the slag,along with the grain width of MgxTi_(3_x)O_(5)(0≤x≤1),decrease with the increase in CR.

关键词： Vanadium-titanium magnetite Vortex smelting reduction Phase reconfiguration TiO_(2)enrichment

Assessment of International GNSS Service Global Ionosphere Map products over China region based on measurements from the Crustal Movement Observation Network of China

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Earth and Planetary Physics 2024年第2期8卷 400-407页

作者： Jin Hu HaiBing Ruan FuQing Huang ShengYang Gu XianKang dou Institute of Space Weather Nanjing University of Information Science and TechnologyNanjing 210044China State Key Laboratory of Space Weather Chinese Academy of Sciences(CAS)Beijing 100190China School of Electronic Information Wuhan UniversityWuhan 430072China Wuxi Research Institute Nanjing University of Information Science and TechnologyWuxi Jiangsu 214000China CAS Key Laboratory of Geospace Environment School of Earth and Space SciencesUniversity of Science and Technology of ChinaHefei 230026China

The global ionosphere maps(GIM)provided by the International GNSS Service(IGS)are extensively utilized for ionospheric morphology monitoring,scientific research,and practical *** the credibility of GIM products in data-sparse regions is of paramount *** this study,measurements from the Crustal Movement Observation Network of China(CMONOC)are leveraged to evaluate the suitability of IGS-GIM products over China region in *** indices of mean error(ME),root mean square error(RMSE),and normalized RMSE(NRMSE)are then utilized to quantify the accuracy of IGS-GIM *** revealed distinct local time and latitudinal dependencies in IGS-GIM errors,with substantially high errors at nighttime(NRMSE:39%)and above 40°latitude(NRMSE:49%).Seasonal differences also emerged,with larger equinoctial deviations(NRMSE:33.5%)compared with summer(20%).A preliminary analysis implied that the irregular assimilation of sparse IGS observations,compounded by China’s distinct geomagnetic topology,may manifest as error *** results suggest that modeling based solely on IGS-GIM observations engenders inadequate representations across China and that a thorough examination would proffer the necessary foundation for advancing regional total electron content(TEC)constructions.

关键词： International GNSS Service(IGS)Global Ionosphere Maps(GIM) Crustal Movement Observation Network of China(CMONOC) total electron content(TEC) data assessment

Ballistic performance of spherical fragments penetrating PCrNi3MoV target plates

在线全文

学校读者我要写书评

暂无评论

Defence Technology（防务技术） 2024年第3期33卷 295-307页

作者： dou Hong Wenbin Li Yu Zheng Yiming Li Ning Jiang Kebin Zhang Ministerial Key Laboratory of ZNDY Nanjing University of Science and TechnologyNanjingChina

PCrNi3MoV steel is a medium-carbon,low-alloy quenched and tempered steel that finds its applications in military gun barrels due to the high wear resistance and ablation *** study the penetration and failure modes of PCrNi3MoV plates impacted by tungsten spheres,tungsten spheres of various diameters(5 mm,8 mm,and 10 mm)were used to impact PCrNi3MoV steel plates with thicknesses of 6 mm,9 mm,and 14 *** penetration performance of the spheres was analyzed for different velocities,and the ultimate penetration velocity of the plate was *** was found that the primary failure modes of the PCrNi3MoV plate were compression pitting failure and shear *** the dimensional analysis method,a relationship between the bulge height of the steel plate and the fragment velocity,an equation for the ultimate penetration velocity,and a relationship between the target penetration energy and the fragment velocity were ***,a projectile-target action index was proposed to describe the process of tungsten spheres with different velocities impacting target *** results suggested that under the same thickness of the target plate,a larger-diameter fragment required more kinetic energy to obtain the same ultimate penetration effect as a smaller-diameter *** equations obtained through dimensional analysis predicted values that agreed well with experimental values,indicating that these equations can be applied to engineering applications.

关键词： Impact damage Ultimate penetration velocity Bulge height Target penetration energy Failure modes

Exploring Trade-offs in Thermal Interface Materials:The Impact of Polymer-Filler Interfaces on Thermal Conductivity and Thixotropy

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Polymer Science 2024年第7期42卷 916-925,I0006页

作者： Bin Zhang Zheng-Li dou Yong-Zheng Zhang Qiang Fu Kai Wu College of Polymer Science and Engineering State Key Laboratory of Polymer Materials EngineeringSichuan UniversityChengdu610065China

Effective thermal transport across solid-solid interfaces which is essential in thermal interface materials(TIMs),necessitates both optimal thixotropy and high thermal *** role of filler surface modification,a fundamental aspect of TIM fabrication,in the influence of these properties is not fully *** study employs the use of a silane coupling agent(SCA)to modify alumina,integrating experimental approaches with molecular dynamics simulations,to elucidate the interface effects on thixotropy and thermal conductivity in polydimethylsiloxane(PDMS)-based *** findings reveal that the variations of SCAs modify both interface binding energy and transition layer *** interface binding energy restricts macromolecular segmental relaxation near the interface,hindering desirable thixotropy and bond line *** the contrary,the thickness of the transition layer at the interface positively influences thermal conductivity,facilitating the transport of phonons between the polymer and ***,selecting an optimal SCA allows a balance between traditionally conflicting goals of high thermal conductivity and minimal bond line thickness,achieving an impressively low interface thermal resistance of just 2.45-4.29 K·mm^(2)·W^(-1)at275.8 kPa.

关键词： Thermal interface material Surface modification Thermal conductivity Thixotropy Interface thermal resistance

Nano-sized stationary phase packings retained by single-particle frit for microchip liquid chromatography

在线全文

学校读者我要写书评

暂无评论

Chinese Chemical Letters 2024年第4期35卷 486-489页

作者： Wangyan Hu Ke Li Xiangnan dou Ning Li Xiayan Wang Center Excellence for Environmental Safety and Biological Effects Beijing Key Laboratory for Green Catalysis and SeparationDepartment of ChemistryBeijing University of TechnologyBeijing 100124China Center for Environmental Metrology National Institute of MetrologyBeijing 100029China

Modern chromatography is increasingly focused on miniaturization and integration. Compared to conventional liquid chromatography, microfluidic chip liquid chromatography(microchip-LC) has the potential due to its zero-dead volume connection and ease of integration. Nano-sized packings have the potential to significantly enhance separation performance in microchip-LC. However, their application has been hindered by packing difficulties. This study presents a method for packing nano-sized silica particles into a microchannel as the stationary phase. The microchip-LC packed column was prepared by combining the weir and the porous silica single-particle as frit to retain the packing particles. A surface tensionbased single-particle picking technique was established to insert porous single-particle frit into glass microchannels. Additionally, we developed a slurry packing method that utilizes air pressure to inject nano-sized packing into the microchannel. Pressure-driven chromatographic separation was performed using this nano-packed column integrated into a glass microchip. The mixture of four PAHs was successfully separated within just 8 min using a 5 mm separation channel length, achieving high theoretical plates(10~6plates/m). Overall, these findings demonstrate the potential of utilizing nano-sized packings for enhancing chromatographic performance in microchip systems.

关键词： Nano-size packing Single-particle frit Packed column Microchip LC Chromatographic separation

Large Deviations for a Critical Galton-Watson Branching Process

在线全文

学校读者我要写书评

暂无评论

Acta Mathematicae Applicatae Sinica 2024年

作者： dou-dou LI Wan-lin SHI Mei ZHANG College of Statistics and Data Science Faculty of Science Beijing University of Technology Laboratory of Mathematics and Complex Systems (Ministry of Education) School of Mathematical SciencesBeijing Normal University Department of Mathematics and Physics North China Electric Power University

In this paper, a critical Galton-Watson branching process{Zn}is considered. Large deviation rates of SZn:=∑i=1ZnXiare obtained, where{Xi, i≥1}is a sequence of independent and identically distributed random variables and X1is in the domain of attraction of an α-stable law with α∈(0, 2). One shall see that the convergence rate is determined by the tail index of X1and the variance of Z1. Our results can be compared with those ones of the supercritical case.

关键词：

Dual-filler reinforced PVDF-HFP based polymer electrolyte enabling high-safety design of lithium metal batteries

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Nano Research 2024年第6期17卷 5251-5260页

作者： Chang Fang Kangsheng Huang Jing Zhao Shiqi Tian Hui dou Xiaogang Zhang Jiangsu Key Laboratory of Electrochemical Energy Storage Technologies College of Materials Science and TechnologyNanjing University of Aeronautics and AstronauticsNanjing 210016China

Despite the high energy density of lithium metal batteries(LMBs),their application in rechargeable batteries is still hampered due to insufficient ***,we present a novel flame-retardant solid-state electrolyte based on polyvinylidene fluoride-hexafluoropropylene(PVDF-HFP)with nano SiO_(2)aerogel as an inert filler but Li_(6.4)La_(3)Zr_(1.4)Ta_(0.6)O_(12)(LLZTO)as an auxiliary component to enhance the ion *** introduction of SiO_(2)aerogels imparts the polymer electrolyte with exceptional thermal stability and flame ***,the interaction between hydroxyl groups of SiO_(2)particles and PVDF-HFP creates a strong cross-linking structure,enhancing the mechanical strength and stability of the ***,the presence of SiO_(2)aerogel and LLZTO facilitates the dissociation of lithium salts through Lewis acid-base interactions,resulting in a high ionic conductivity of 1.01×10^(−3)S·cm^(−1)and a wide electrochemical window of~5.0 V at room temperature for the prepared ***,the assembled Li|Li cell demonstrates the excellent resistance to lithium dendrite and runs stablly for over 1500 h at a current density of 0.25 mA·cm^(−2).Thus,we prepare a pouch cell with high safety,which can work normally after short-circuiting under the external folding and cutting.

关键词： polymer electrolyte SiO_(2)/Li_(6.4)La_(3)Zr_(1.4)Ta_(0.6)O_(12)(LLZTO)dual-filler non-flammable long cycle life lithium metal battery

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

风荷载作用下施工栈道钢管桩施工稳定性分析

水利水电技术 2019年第9期50卷 98-107页

作者：谢晓鹏窦国涛杨露高波李晗郑州航空工业管理学院土木建筑学院河南郑州450046 河南工程学院土木工程学院河南郑州451191 江苏省交通工程集团有限公司江苏镇江212100

针对钢管桩上下部剪力撑不同施工次序所引起的风荷载响应问题,为了揭示施工过程中风荷载对钢管桩稳定性的影响规律,以黄河大桥施工栈道钢管桩施工过程为背景,采用谐波叠加法合成了风荷载,对钢管桩不同施工次序中风荷载的影响进行了分析... 详细信息

针对钢管桩上下部剪力撑不同施工次序所引起的风荷载响应问题,为了揭示施工过程中风荷载对钢管桩稳定性的影响规律,以黄河大桥施工栈道钢管桩施工过程为背景,采用谐波叠加法合成了风荷载,对钢管桩不同施工次序中风荷载的影响进行了分析研究.结果表明:钢管桩施工过程中,风荷载的作用会使钢管桩产生位移;当下部剪力撑焊接完毕而上部剪力撑未焊接时,风荷载作用下桩顶平均位移为0.337 m,最大位移为0.384 m;当上部剪力撑焊接完毕而下部剪力撑未焊接时,风荷载作用下桩顶平均位移为0.704 m,最大位移为0.767 m;当上部剪力撑和下部剪力撑焊接完毕后,风荷载作用下桩顶平均位移为0.3447 m,最大位移为0.404 2 m;同一时刻,风荷载作用下,钢管桩位移随着钢管桩高度位置的增大而增大,钢管桩的最大米塞斯应力随着桩项位移的增大而增大,钢管桩最大米塞斯应力位于钢管桩中下部.研究成果对钢管桩剪力撑的施工次序设计具有参考价值.

关键词：风荷载施工栈道钢管桩剪力撑桩顶位移

钢栈桥桩顶梁截面ANSYS简化对其力学性能的影响

在线全文

学校读者我要写书评

暂无评论

河南理工大学学报（自然科学版） 2020年第4期39卷 140-146页

作者：谢晓鹏王娟窦国涛李晗高波郑州航空工业管理学院土木建筑学院河南郑州450046 郑州大学水利与环境学院河南郑州450001 江苏省交通工程集团有限公司江苏镇江212100

为了研究钢栈桥桩顶梁截面形式在ANSYS中简化后对其力学性能的影响,以黄河大桥施工栈道桩顶梁为研究对象,利用ANSYS建立原始模型和简化模型,首先分析静力作用下两者应力的差异,然后分析风荷载作用下施工栈道动力响应的差异。结果表明:(1... 详细信息

为了研究钢栈桥桩顶梁截面形式在ANSYS中简化后对其力学性能的影响,以黄河大桥施工栈道桩顶梁为研究对象,利用ANSYS建立原始模型和简化模型,首先分析静力作用下两者应力的差异,然后分析风荷载作用下施工栈道动力响应的差异。结果表明:(1)在上部结构自重作用(静力作用)下,两者最大竖向位移相差仅为0.56%,米塞斯应力相差仅为0.68%;(2)在风荷载作用(动力作用)下,两者桩顶梁中部节点最大速度绝对值相差0.023%,最大加速度绝对值相差0.2%。在上部结构自重作用或者风荷载作用下进行钢栈桥受力分析时,可用简化截面代替原截面进行计算。

关键词：钢栈桥桩顶梁有限元模拟梁截面简化风荷载