检索结果-南通市图书馆

Study on the relative radiometric correction of CBERS satellite CCD image

Science china(Technological Sciences) 2005年第S2期48卷 12-28页

作者： GUO Jianning, YU Jin, ZENG Yong, XU Jianyan, PAN Zhiqiang & HOU Minghui china center for resource Satellite data and application, beijing 10083., china china Ctr resource Satellite data & Applicat Beijing 100830 Peoples R China

The main payload on CBERS-01/02 of china-Brazil Earth resources Satellite (CBERS) is a push-broom CCD camera with moderate spatial and radiant resolution. Because at lab the data for calibration at satellite assembly stage were unable to be collected, and also because the onboard calibrator after launch was in a different state from imaging, the calibration of CCD image got a series of difficulties involved. In practice, two methods are used in the processing on the ground station: One is extracting calibration data by statistics from the image itself, and the other is the method of histogram match. It was proved that the latter can calibrate the image much better, because it can remove the effect of unstable response of the camera largely and also can overcome the nonlinearity of the camera basically by using Look-Up Table (LUT) calculated from histogram statistics of different temporal images. Considering the problems of CBERS-01, a lot of calibration tests were done before the launch of CBERS-02, in which a set of lab coefficients for relative calibration was formulated after the data collection by using integration-hemisphere in the stage of satellite assembly test. During the on-orbit test, it was found that the calibration result from such coefficients was not satisfying, especially there being response difference between 3 detector arrays, which was attributed to the unstable dark currents of the CCD camera. This paper comes up with a statistic method to remove such response difference. In this method the middle detector array was used as reference to find the response differences of adjacent similar features between these arrays and it was proved to have a broad adaptability.

关键词： CBERS satellite CCD camera relative radiometric calibration relative radiometric correction assembly test.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Study of thin cloud removal method for CBERS-02 image

引用

Science china(Technological Sciences) 2005年第S2期48卷 91-99页

作者： MA Jianwen1, GU Xingfa1, FENG Chun2 & GUO Jianning2 1. Institute of Remote Sensing application, Chinese Academy of Sciences, beijing 100101, china 2. china center for resource Satellite {6. and applications, beijing 100073, china 1. Institute of Remote Sensing application Chinese Academy of Sciences 100101 Beijing China 2. china center for resource Satellite data and applications 100073 Beijing China

The china Brazil Earth resources Satellite (CBERS) ended the dependence on foreign satellites. Along with the series of CBERS and the enhancement of satellite applications, it is necessary to search correlative data processing methods. Because cloud appears in the atmosphere, an image with clear sky conditions is often hard to obtain. How to remove cloud is an important sector of increasing image quality. An improved homomorphism filtering method is adopted to remove thin cloud qualitatively at first, and all bands are selected to classify pixels. Based on the fact that visible band images contain more aerosol effects than infrared bands, visible bands are used to determine clear or hazy regions and the reflectances of different surface classes in clear regions are calculated. At last the mean reflectance of the same classes in clear and hazy regions is matched to remove cloud. The image visual effect is improved; meanwhile, the ground reflectance is retrieved to meet the needs of remote sensing quantification.

关键词： CBERS-02 cloud removal surface reflectance mean reflectance matching.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

In flight MTF monitoring and compensation for CCD camera on CBERS-02

引用

Science china(Technological Sciences) 2005年第S2期48卷 29-43页

作者： GU Xingfa1,2,3, LI Xiaoying1,2,4, MIN Xiangjun5, YU Tao1,2, SUN Jijuan5, ZENG Yong1,2,4, XU Hua1,2 & GUO Ding2,6.1. State Key Laboratory of Remote Sensing Science, Jointly Sponsored by the Institute of Remote Sensing applications of Chinese Academy of Sciences and beijing Normal University, beijing 100101, china 2. The center for National Spaceborne Demonstration, beijing 100101, china 3. Institut National de la Recherche Agronomique, Climat Sol Environnement, 84914 Avignon, France 4. Graduate University of Chinese Academy of Sciences, beijing 100039, china 5. china center for resource Satellite data and application, beijing 10083., china 6. University of Electronic Science and Technology of china, Chengdu 6.0054, china State Key Laboratory of Remote Sensing Science Jointly Sponsored by the Institute of Remote Sensing Applications of Chinese Academy of Sciences and Beijing Normal University 100101 Beijing China The center for National Spaceborne Demonstration 100101 Beijing China Institut National de la Recherche Agronomique Climat Sol Environnement 84914 Avignon France Graduate University of Chinese Academy of Sciences 100039 Beijing China china center for resource Satellite data and application 100830 Beijing China University of Electronic Science and Technology of china 610054 Chengdu China

In this article, the approach of simulating ideal tarp scene was proposed to determine the MTF for CCD camera on CBERS-02. The MTF acquired from this technique was compared to those from some common methods. MTFs achieved from different approaches were employed to compensate the CCD images based on three restoration algorithms: the iterative method, the Wiener filter and the modified inverse filter (MIF). The two-dimensional MTF was established with the value at frequency 0.5 for 45° directional MTF as the value at its four corners. This article addressed the variations of the restored CCD images with different techniques of constructing two-dimensional MTF, restoring algorithms and determining the in-flight MTFs. Results showed images restored with the MTF determined from the technique of simulating ideal tarp scene represent the real scene best. And the restoration technique based on the MIF would produce better restored images than the other two techniques. This research also demonstrated that the two-dimensional MTF used for restoration should be interpolated under the control of the MTF for 45° axis, rather than by multiplying the cross-orbit MTF with along-orbit MTF.

关键词： CBERS-02 CCD MTF the technique of simulating ideal tarp scene.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

The quantification of remote sensing

引用

Science china(Technological Sciences) 2005年第S2期48卷 1-11页

作者： GU Xingfa1,2,3,TIAN Guoliang1,2, LI Xiaowen1,2 & GUO Jianning4 1. State Key Laboratory of Remote Sensing Science, Jointly Sponsored by the Institute of Remote Sensing applications of Chinese Academy of Sciences and beijing Normal University, beijing 100101, china 2. The center for National Spaceborne Demonstration, beijing 100101, china 3. Institut National de la Recherche Agronomique, Climat Sol Environnement, 84914 Avignon, France 4. china center for resource Satellite data and application, beijing 10083., china Chinese Acad Sci Inst Remote Sensing Applicat State Key Lab Remote Sensing Sci Beijing 100101 Peoples R China beijing Normal Univ State Key Lab Remote Sensing Sci Beijing 100101 Peoples R China Ctr Natl Spaceborne Demonstrat Beijing 100101 Peoples R China Inst Natl Rech Agron F-84914 Avignon France china Ctr resource Satellite data & Applicat Beijing 100830 Peoples R China

The paper firstly defined the remote sensing information quantification, analyzed the necessity of developing remote sensing quantification, figured out the application guidelines requirement, and pointed out the importance of quantification research. Then taking the remote sensing application research of CBERS-02 data quantification as the example, the paper described the whole quantification system of “remotely sensed digital signal-radiation information-field parameter inversion”. Finally the paper gave the prospect for the development trend of the quantitative remote sensing.

关键词： remote sensing information quantification CBERS-02 radiometric calibration surface parame- ter reversion.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Water target based cross-calibration of CBERS-02 CCD camera with MODIS data

引用

Science china(Technological Sciences) 2005年第S2期48卷 61-71页

作者： TANG Junwu1,2, GU Xingfa2, NIU Shengli1, MA Chaofei1 & MIN Xiangjun3 1. National Satellite Ocean application Service (NSOAS), beijing 100081, china 2. State Key Laboratory of Remote Sensing Science, beijing 100010, china 3. china {6. for resource Satellite data and applications (CRESDA), beijing 100083, china 1. National Satellite Ocean application Service (NSOAS) 100081 Beijing China 2. State Key Laboratory of Remote Sensing Science 100010 Beijing China 3. china center for resource Satellite data and applications (CRESDA) 100083 Beijing China

In order to make quantitative watercolor sensing with china-Brazil Earth resources Satellite (CBERS-02) CCD camera, the MODIS data with higher accuracy is used to cross-calibrate the CCD camera over water targets. In homogeneous clear water area, two pairs of images obtained over the same area on the same day by the two sensors are selected. The top-of-atmosphere (TOA) radiances of the multispectral bands of CCD are calculated with the water and aerosol parameters from MODIS based on a water-atmosphere radiative transfer algorithm. The stripes in CCD image that caused by unequal response of the CCD array detectors are firstly removed before making the cross-calibration. The same part of CCD detectors is selected for the calibrations in the two images to eliminate the residual error of destriping and uniformity correction for the focus plane irradiance. It is shown that the calibration results from two different images are consistent. The error of this method is about 5%.

关键词： CBERS-02 CCD MODIS radiometric calibration cross-calibration. DOI: 10.13.0/05ze1006

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Comparison of the influence factors on NDVI for CCD camera and WFI imager on CBERS-02

引用

Science china(Technological Sciences) 2005年第S2期48卷 100-115页

作者： YU Tao1,3, LI Xiaoying1,2,3, ZHANG Yong1,2,3, ZHAO Feng1,2,3, GU Xingfa1,3,4, ZHU Li1,2,3, WANG Pengxin5 & MIN Xiangjun6.1. State Key Laboratory of Remote Sensing Science Institute of Remote Sensing application, CAS, Bei- jing 100101, china 2. Graduate University of Chinese Academy of Sciences, beijing 100039, china 3. The center for National Spaceborne Demonstration, beijing 100101, china 4. Institut National de la Recherche Agronomique, Climat Sol Environnement, 84914 Avignon, France 5. College of Information and Electrical Engineering, china Agricultural University, beijing 100083, china 6. china center for resource Satellite {13. and application, beijing 10083., china 1. State Key Laboratory of Remote Sensing Science Institute of Remote Sensing Application CAS 100101 Beijing China 2. The center for National Spaceborne Demonstration 100101 Beijing China 3. Graduate University of Chinese Academy of Sciences 100039 Beijing China 4. Institut National de la Recherche Agronomique Climat Sol Environnent 84914 Avignon France 5. College of Information and Electrical Engineering China Agricultural University 100083 Beijing China 6. china center for resource Satellite data and application 100830 Beijing China

CCD and WFI are payloads in the visible light and near infrared bands on CBERS satellites and they have not been applied widely, especially WFI. This article mainly probes into the potential of these two sensors’ application in the vegetation monitoring and analyses the influences of radiometric calibration, atmosphere conditions and sun-observing geometry, etc. on NDVI obtained from these two sensors respectively. In addition it analyses the effect of the spectral response difference of red and near infrared spectral bands in CCD and WFI sensors on NDVI. Results indicate that radiometric calibration is the most important factor on NDVI, which cannot be applied to vegetation monitoring without radiometric calibration. Results also demonstrate that near surface NDVI is different greatly from that of TOA which change with atmosphere conditions. The study shows that NDVI is also affected by the non-lambertian character of surface and the change of the atmospheric path with the observing geometry. And NDVI of WFI is higher than that of CCD. They are very different because of their spectral difference, but they have a good linear relevant relationship.

关键词： CCD WFI NDVI LAI.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Radiometric cross-calibration of the CBERS-02 CCD camera with the TERRA MODIS

引用

Science china(Technological Sciences) 2005年第S2期48卷 44-60页

作者： LI Xiaoying1,2,3, GU Xingfa1,3,4, MIN Xiangjun5, YU Tao1,3, FU Qiaoyan5, ZHANG Yong1,2,3 & LI Xiaowen1,3 1. State Key Laboratory of Remote Sensing Science, Jointly Sponsored by the Institute of Remote Sensing applications of Chinese Academy of Sciences and beijing Normal University, beijing 100101, china 2. Graduate University of Chinese Academy of Sciences, beijing 100039, china 3. The {6. for National Spaceborne Demonstration, beijing 100101, china 4. Institut National de la Recherche Agronomique, Climat Sol Environnement, 84914 Avignon, France 5. china {6. for resource Satellite data and application, beijing 10083., china 1. State Key Laboratory of Remote Sensing Science Jointly Sponsored by the Institute of Remote Sensing Applications of Chinese Academy of Sciences and Beijing Normal University 100101 Beijing China 2. Graduate University of Chinese Academy of Sciences 100039 Beijing China 3. The center for National Spaceborne Demonstration 100101 Beijing China 4. Institut National de la Recherche Agronomique Climat Sol Environnement 84914 Avignon France 5. china center for resource Satellite data and application 100830 Beijing China

For the application of the CCD camera, the most important payload on CBERS-02, the key is to provide long-term stable radiometric calibration coefficients. Although the vicarious calibration had been proved successful, it had its limitations such as test site requirement and unsuitable for historical data. Cross-calibration is one of the alternative methods, but it needs synchro surface spectrum to achieve spectral band matching factors. Our effort is to probe the influences on these factors. Simulations with a lot of surface spectrum showed that the factors changed with the viewing geometry, atmospheric condition and surface targets. However, simulating with the same viewing geometry and atmospheric condition, the spectral band matching factors of the same or similar surface targets’ spectrum acquired from different dates and different places would like to be consistent to each other within 1%―5%. Thus, the synchro measurement data can be substituted by the same or similar target from other source. Based on this method, using the MODIS as the reference, the cross-calibration was performed for CCD camera. The research demonstrated that the traditional method with single calibration site was inappropriate for CCD camera, since the offsets for its four spectral bands were not zeros. With four calibration sites, these offsets were obtained. And the camera was detected to degrade with dates based on four times of cross-calibrations.

关键词： CBERS-02 CCD camera cross-calibration the spectral band matching factors.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Study on attribute characterization for reservoir dynamic monitoring by seismic

引用

Science china Earth Sciences 2008年第S2期51卷 218-225页

作者： CHEN XiaoHong1,3,LI JingYe2,3 & ZHAO Wei4 1 Key Lab of Geophysical Exploration of CNPC,china Petroleum University,beijing 102249,china 2 Basin & Reservoir Research center,china Petroleum University,beijing 102249,china 3 State Key Laboratory of Petroleum resource and Prospecting,china University of Petroleum,beijing 102249,china 4 Research center of CNOOC,beijing 100027,china 1. Key Lab of Geophysical Exploration of CNPC China Petroleum University Beijing 102249 China 3. State Key Laboratory of Petroleum resource and Prospecting China University of Petroleum Beijing 102249 China 2. Basin & Reservoir Research center China Petroleum University Beijing 102249 China 4. Research center of CNOOC Beijing 100027 China

Study on characterizing reservoir parameters dynamic variations by time-lapse seismic attributes is the theoretical basis for effectively distinguishing reservoir parameters variations and conducting time-lapse seismic interpretation,and it is also a key step for time-lapse seismic application in real oil fields. Based on the rock physical model of unconsolidated sandstone,the different effects of oil saturation and effective pressure variations on seismic P-wave and S-wave velocities are calculated and analyzed. Using numerical simulation on decoupled wave equations,the responses of seismic amplitude with different offsets to reservoir oil saturation variations are analyzed,pre-stack time-lapse seismic attributes differences for oil saturation and effective pressure variations of P-P wave and P-S converted wave are calculated,and time-lapse seismic AVO (Amplitude Versus Offset) response rules of P-P wave and P-S converted wave to effective pressure and oil saturation variations are compared. The theoretical modeling study shows that it is feasible to distinguish different reservoir parameters dynamic variations by pre-stack time-lapse seismic information,including pre-stack time-lapse seismic attributes and AVO information,which has great potential in improving time-lapse seismic interpreta-tion precision. It also shows that the time-lapse seismic response mechanism study on objective oil fields is especially important in establishing effective time-lapse seismic data process and interpreta-tion scheme.

关键词： time-lapse seismic dynamic monitoring rock physical model pre-stack attribute Amplitude Versus Offset (AVO)

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Mineralization episode of porphyry copper deposits in the Jinshajiang-Red River mineralization belt: Re-Os dating

引用

Science china Earth Sciences 2005年第2期48卷 192-198页

作者： WANG Denghong, QU Wenjun, LI Zhiwei, YIN Hanlong4 & CHEN Yuchuan Institute of Mineral resources, Chinese Academy of Geological Sciences, beijing 100037, china National center of Rock and Mineral Analysis, Chinese Academy of Geological Sciences, beijing 100037, china resource Assessment center of Yunnan, Kunming 6.0011, china Institute of Geology and Geophysics, Chinese Academy of Sciences, beijing 100101, china Chinese Academy of Geological Sciences, beijing 100037, china 1. Institute of Mineral resources Chinese Academy of Geological Sciences 100037 Beijing China 2. National center of Rock and Mineral Analysis Chinese Academy of Geological Sciences 100037 Beijing China 3. resource Assessment center of Yunnan 650011 Kunming China 4. Institute of Geology and Geophysics Chinese Academy of Sciences 100101 Beijing China 5. Chinese Academy of Geological Sciences 100037 Beijing China

Re-Os isotopic dating for the molybdenites from the porphyry copper deposits of the Jinshajiang-Red River mineralization belt in Yunnan Province yields isochron ages of 33.9±1.1 Ma for the Machangqing deposit and 34.4±0.5 Ma for the Tongchang deposit. This result shows that both the Machangqing and the Tongchang porphyry Cu-Mo deposits from two different ore-fields formed simultaneously. This new data and the published Re-Os model ages of molybdenite (35.4 Ma, 35.9 Ma, 36.2 Ma) of the Yulong porphyry copper deposit in Tibet, which is located in the same Jinshajiang-Red River mineralization belt as the Machangqing deposit and the Tongchang deposit, suggest that these three Cenozoic porphyry copper deposits in the Jinshajiang-Red River mineralization belt were contemporary for their mineralization episode. That is to say, even their present locality is far away and nearly iso-distantly distributed, these three porphyry Cu(Mo) deposits belong to the same mineralization episode at the end of Eocene.

关键词： Re-Os isotopic dating, porphyry Cu deposits, Cenozoic, mineralization episode.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

On three-dimensional geological modeling and visualization

引用

Science china Earth Sciences 2004年第8期47卷 739-748页

作者： WU Qiang1 & XU Hua2 1. Department of resource Exploitation Engineering, china University of Mining and Technology, beijing 100083, china 2. beijing Institute of Petrochemical Technology, beijing 1026.7, china 1. Department of resource Exploitation Engineering China University of Mining and Technology 100083 Beijing China 2. beijing Institute of Petrochemical Technology 102617 Beijing China

The technology of 3D geological modeling will bring about great changes in the methods of geological data acquiring, storing, processing and displaying. However, no perfect or convenient software systems have been developed up to now since the geologic data which re-flect geological entities bear the feature of diversity, uncertainty and complexity. Some supervoxel models, mathematical models of fault and geometrical models of fold have been contrived so as to show the space geometric configuration of the complicated geologic structures. The application-oriented system architecture for 3D geological modeling is established; and a novel design concept based on spatial data processing is also proposed with the technology of solid modeling as its core and the application of models as its objective. Theories and methods for 3D geological modeling will hopefully be enriched and developed. In the light of these theories and methods, a feature-based navigation visualization technique is also put forward in the paper. By integrating geo-database, graphics libraries and KBS with 3D dynamic simulation systems, geologists will be able to capture the partial characteristics and whole structure embodied in the geological data in a direct-viewing, figurative and accurate manner.

关键词： 3D geological modeling,geometrical model,system architecture,visualization

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：