检索结果-南通市图书馆

Mechanical Behavior and Failure Mechanism of an As-Extruded Mg-11wt%Y Alloy at Elevated Temperature

Acta Metallurgica Sinica(English Letters) 2024年第6期37卷 969-981页

作者： Lan Zhang Dao-Kui Xu Bao-Jie Wang Cui-Lan Lu Shuo Wang Xiang-Bo Xu Dong-Liang Wang Xin Lv En-Hou Han School of Materials Science and Engineering University of Science and Technology of ChinaShenyang110016China Key Laboratory of Nuclear Materials and Safety Assessment Institute of Metal ResearchChinese Academy of SciencesShenyang110016China School of Environmental and Chemical Engineering Shenyang Ligong UniversityShenyang110159China Key Lab of Electromagnetic Processing of Materials Ministry of EducationNortheastern UniversityShenyang110819China institute of Corrosion Science and Technology Guangdong510070China

Through carrying out the high-temperature tensile experiments on an as-extruded Mg-11wt%Y alloy at 350℃,400℃,450℃,500℃and 550℃,the mechanical behavior and fracture mechanisms at elevated temperatures are investigated and *** results show that with the increase of temperature,the yield strength and ultimate tensile strength of the alloy increase at first and then decrease,while that the elongation ratio decreases firstly and then *** the sample being tested at 350℃,the values of yield strength,ultimate tensile strength and the elongation ratio are 188 MPa,266 MPa and 11%,*** 400℃,the yield strength and ultimate tensile strength reach the maximum values of,respectively,198 MPa and 277 MPa,but the elongation ratio is the lowest and its value is only 8%.When the applied temperature is increased to 550℃,the values of yield strength and ultimate tensile strength,respectively,decrease to 140 MPa and 192 MPa and the elongation ratio increases to 38%.Failure analysis demonstrates that the fracture surfaces of different samples are mainly composed of plastic dimples and exhibit the typical characteristic of ductile *** observation to the fracture side surfaces indicates that at the temperatures of 350℃and 400℃,microcracks mainly initiate in the interior of Mg_(24)Y_(5)*** the temperatures are 450℃,500℃and 550℃,the cracks preferentially initiate at the Mg_(24)Y_(5)/α-Mg interfaces.

关键词： Mg-Y alloy High-temperature tensile properties Fracture mechanism Failure analysis

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Numerical simulation of melt flow and temperature field during DC casting 2024 aluminium alloy under different casting conditions

引用

China Foundry 2024年第4期21卷 387-396页

作者： Jin-chuan Wang Yu-bo Zuo Qing-feng Zhu Jing Li Rui Wang Xu-dong Liu Key Laboratory of Electromagnetic Processing of Materials Ministry of EducationNortheastern UniversityShenyang 110819China School of Materials Science and Engineering Northeastern UniversityShenyang 110819China Engineering research Center of Advanced Materials Preparing Technology Ministry of EducationShenyang 110819China CAS Key Laboratory of Nuclear Materials and Safety Assessment Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China

Casting speed,casting temperature and secondary cooling water flow rate are the main process parameters affecting the DC casting *** parameters significantly influence the flow and temperature fields during casting,which are crucial for the quality of the ingot and can determine the success or failure of the casting *** simulation,with the advantages of low cost,rapid execution,and visualized results,is an important method to study and optimize the DC casting *** the present work,a simulation model of DC casting 2024 aluminum alloy was established,and the reliability of the model was ***,the influence of casting parameters on flow field and temperature field was studied in detail by numerical simulation *** show that with the increase of casting speed,the melt flow becomes faster,the depths of slurry zone and mushy zone increase,and the variation of slurry zone depth is greater than that of mushy *** an increase in casting temperature,the melt flow rate increases,the depth of the slurry zone becomes shallower,and the depth of the mushy zone experiences only minor *** simulation results further indicate that the increase of the flow rate of the secondary cooling water slightly reduces the depths of both slurry and mushy zone.

关键词： aluminium DC casting flow field temperature field numerical simulation

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Adaptive PI Control Based Stability Margin Configuration of Aircraft Control Systems with Unknown System Parameters and Time Delay

引用

Journal of Systems Science & Complexity 2024年第4期37卷 1507-1525页

作者： ZHANG Zhibing ZHOU Dapeng WANG Yeguang GAO Wanxin ZHANG Yanjun AVIC shenyang Aircraft Design and research institute Shenyang 110035China School of Automation Beijing Institute of TechnologyBeijing 100081China State Key Lab of Autonomous Intelligent Unmanned Systems Beijing Institute of TechnologyBeijing 100081China

The stability margin is a vital indicator for assessing the safety level of aircraft control *** should maintain sufficient stability margin to ensure safety during flight,especially in the process of large maneuver *** stability margin is generally quantified by the Bode diagram,which strictly depends on the system parameters and the open-loop transfer ***,due to the uncertain flight environments,transmission delays of sensors and mode switchings,etc.,there exist large parameter and structure uncertainties in the aircraft control systems,which make it difficult to precisely configure the stability margin to the desired value by the usual control *** address this problem,an indirect adaptive control strategy is proposed in this paper,where an adaptive PI control law with the capability of self-configuration of stability margin is *** developed control law not only achieves stable time-varying command tracking in the time domain,but also is able to automatically configure the phase margin and gain margin in the frequency ***,the simulation of the one-degree-of-freedom roll rate control model of the air vehicle verifies the validity of the proposed control method.

关键词： Adaptive control aircraft control parameter uncertainty stability margin configuration

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

High-Speed Rubbing Behavior of Abrasive Coating Coated on Titanium Alloy Blade Tips

引用

Acta Metallurgica Sinica(English Letters) 2024年第4期37卷 749-762页

作者： Wenshuang Gu Shuai Yang Shiyi Zhang Zhiliang Pei Weihai Xue Deli Duan Jun Gong Chao Sun Shi-Changxu Innovation Center for Advanced Materials Institute of Metal ResearchChinese Academy of SciencesShenyang110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang110016China

In aero-engines, abrasive coatings are typically utilized to protect the blade tip from excessive wear caused by the harder abradable sealing coating and thereby improve the sealing performance of engines. Therefore, a Ni/cBN abrasive coating was prepared on titanium alloy using electrodeposition. The high-speed rubbing tests with a linear velocity of 350 m/s and different incursion rates were performed to investigate the effect of the Ni/cBN abrasive coating on the wear behavior against NiCrAl/diatomite seal coating. Results showed that melting wear and adhesive transfer occurred on the bare blades, causing the bare blade to suffer excessive wear. While the Ni/cBN abrasive coating exhibited superior wear resistance and cutting performance. The cBN grits pullout, the abrasion of Ni matrix and transfer of seal coating to the cBN grits were the main wear mechanism of the Ni/cBN abrasive coating. Additionally, it was found that the relationship between the incursion rate and high-speed rubbing behavior is quite different for the bare blade and Ni/cBN coating. The reason for the difference in wear behavior of bare blade and Ni/cBN coating at different incursion rates was discussed in detail.

关键词： Gas turbine sealing Abrasive coating High-speed rubbing Material transfer Abradable coating

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Effects of rare earth elements on inclusions, microstructure and impact toughness of spring steel

引用

Journal of Iron and Steel research International 2024年第4期31卷 933-944页

作者： Chun-lei Hao Chao-yun Yang Peng Liu Yi-kun Luan Bao-guang Sang shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang 110016LiaoningChina School of Mechanical Engineering and Automation Dalian Polytechnic UniversityDalian 116034LiaoningChina

Spring steel is an indispensable basic part manufacturing material in mechanical equipment,which is widely used in transportation tools such as automobiles,railways,construction machinery and other *** effects of rare earth(RE)on inclusions,microstructure,carbides and impact toughness of 50CrV spring steel were studied by means of optical microscope,scanning electron microscope,transmission electron microscope and impact *** results show that the addition of rare earth can modify the main MnS and Al_(2)O_(3) inclusions in steel to form spherical or near-spherical rare earth inclusions,and the size of inclusions is significantly *** the quenched structure,the size of martensite slab becomes smaller and the structure is *** tempering,the carbide changes from sheet to ellipse,which makes it easier for spring steel to form stress concentration cracks under *** becomes finer and more dispersed,which leads to better pinning of grain boundaries and smaller grain *** impact toughness of 50CrV-RE spring steel increased from 21 to 41 J by 95%due to the improvement of inclusions,microstructure and carbides by rare *** is possible to improve the strength and toughness of spring steel for the improvement of railway running speed and the development of vehicle lightweight in China.

关键词： Rare earth-Spring steel Inclusion Microstructure Impact toughness

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Facile preparation of a SiC@SiO_(2)nanowire-toughened ZrB_(2)-SiC/SiC bilayer coating with good interfacial bonding,high toughness,and excellent cyclic ablation resistance on C/CA composites

引用

Journal of Advanced Ceramics 2024年第4期13卷 486-495页

作者： Meng Yan Chenglong Hu Jian Li Shengyang Pang Bohui Sun Rida Zhao Bin Liang Rui Luo Sufang Tang Shi-Changxu Innovation Center for Advanced Materials Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China

Preparing antioxidant coatings to address the inherent oxidation sensitivity of carbon fiber-reinforced carbon aerogel(C/CA)composites is a feasible way to promote their application in oxidizing environments as thermal insulation ***,preparing the coatings with excellent oxidation and ablation resistance while avoiding evident damage to the C/CA substrate still remains a ***,a SiC@SiO_(2)nanowire-toughened ZrB2–SiC/SiC bilayer coating with a large thickness of 500μm was prepared on C/CA using a one-step low-temperature reaction sintering method,which simultaneously formed a sintered outer layer with even-distributed nanowires and a siliconized gradient inner *** courtesy of the synergic thermal response of the layers and the crack deflection induced by the nanowires,the resulting coating has moderate residual compressive stress of 0.08–1.22 GPa in the interface,high interfacial bonding strength of 6.02 MPa,and good fracture toughness of 4.36 MPa·m^(1/2).Benefited from the optimum components and improved structure,the coating shows excellent cyclic ablation resistance with linear ablation rates of 0.1μm/s at 1650℃for 1500 s(300 s×5 cycles)and 0.4μm/s at 1850℃for 900 s(300 s×3 cycles).The one-step preparation strategy contributes to little damage to the substrate,thus showing the well-preserved mechanical and thermal insulation properties.

关键词： coating carbon fiber reinforced carbon aerogel(C/CA)composites toughness interface residual stress

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Martensite decomposition under thermal-mechanical coupling conditions to fabricate an ultrafine-grained Ti6Al4Mo4Zr1W0.2Si alloy

引用

Journal of Materials Science & Technology 2024年第1期168卷 157-168页

作者： Taoyu Zhou Jiuxu Yang Nan Li Hao Sun Bohua Zhang Zibo Zhao Qingjiang Wang Shi-changxu Innovation Center for Advanced Materials Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China

The fabrication of ultrafine-grained microstructures(grain size below 1μm)in titanium alloys is beneficial for improving their mechanical properties at room temperature and medium tempera-tures(400-550°C).However,a long-standing challenge involves the low-cost manufacturing of bulk ultrafine-grained titanium *** this work,we developed a facile strategy through martensite de-composition at thermal-mechanical coupling conditions,to fabricate an equiaxed microstructure in a Ti6Al4Mo4Zr1W0.2Si model alloy with an averageαgrain size of 315±62 *** formation of the ultrafine-grained microstructure was because the lattice strain stored in the martensitic initial mi-crostructure enhanced the nucleation rate of dynamic recrystallization,meanwhile,the pinning role of martensite decomposition productsβand(Ti,Zr)_(5)Si_(3)phases suppressed grain coarsening at high *** to conventional(α+β)alloys,the tensile strength of this alloy improved by 20%-30%at both room temperature and 550°C,without decreasing its *** situ SEM observations revealed that the ultrafine-grained microstructure would not only suppress dislocation motions but also contribute to the homogenous deformation in the matrix of the material,therefore,it resulted in higher mechanical *** research results may be of great significance to the development of next-generation aviation titanium alloys.

关键词： Ultrafine-grained Titanium alloy In situ observation Deformation mechanism Thermostability

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Revealing the Void Formation Mechanism during Superplastic Deformation of a Fine-Grained Ni-Co-Base Superalloy

引用

Acta Metallurgica Sinica(English Letters) 2024年第5期37卷 915-920页

作者： Rashad AAl-Hammadi Rui Zhang Chuanyong Cui Zijian Zhou Yizhou Zhou Shi-Changxu Innovation Center for Advanced Materials Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China

The mechanism behind void formation during superplasticity remains a subject of *** study presented a novel insight into the void formation in a fine-grained Ni-Co-based superalloy during *** was observed that the dissolution ofγ′-particles resulted in the creation of vacancies due to differences in atomic size between the matrix and the *** vacancies acted as inclusions,leading to the formation of ***,excessive void formation correlated with higher particle dissolution was experimentally observed,highlighting a direct relationship between void formation and particle dissolution.

关键词： Superplasticity Void formation Ni-Co-based superalloy Microstructure

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Photoluminescence and ratiometric thermo-response of Eu^(2+)and Eu^(3+)in BaAl_(2)B_(2)O_(7):Eu^(2+),Eu^(3+)phosphor materials

引用

Journal of Rare Earths 2024年第7期42卷 1240-1249,I0002页

作者： Ziyao Wang Haitao Fu Xiufeng Zhan Bo Tong Guofeng Ma H.T.(Bert)Hintzen institute of Innovative Science and Technology Shenyang UniversityShenyang110044China College of Mechanical Engineering Shenyang UniversityShenyang110044China Faculty of Applied Sciences Delft University of Technology2629 JBDelftthe Netherlands

A novel Eu^(2+)-Eu^(3+)co-activated ratiometric thermo-sensitive phosphor was developed and synthesized by solid-state *** valence state of Eu,photoluminescence and thermo-sensitive performance of the phosphor prepared either in ambient air or carbothermally were investigated and *** phosphor shows high sensitivity(Sa=0.0173 K^(-1),S_(r)=0.461%/K)and superior signal discriminability(Δν∼10380 cm^(−1)).The thermo-sensitive performance is subject to the dual effects of different thermo-responses by Eu^(2+)versus Eu^(3+)combined with energy transfer from Eu^(2+)to Eu^(3+),so that the sensitivity of the phosphor in the temperature range presents a non-monotonic *** development of the BaAl_(2)B_(2)O_(7):Eu^(2+),Eu^(3+)phosphor is not only expected to be relevant for application in the field of temperature sensing,but also of reference significance for improving the sensitivity by means of energy transfer between co-activator ions over a wider temperature range of Eu^(2+)-Eu^(3+)co-activated ratiometric thermo-sensitive phosphors.

关键词： Photoluminescence Ratiometric thermo-response Phosphor Eu^(2+)/Eu^(3+) Rare earths

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

research on Leading Edge Erosion and Aerodynamic Characteristics of Wind Turbine Blade Airfoil

引用

Fluid Dynamics & Materials Processing 2024年第9期20卷 2045-2058页

作者： Xin Guan Yuqi Xie Shuaijie Wang Mingyang Li Shiwei Wu School of New Energy Shenyang Institute of EngineeringShenyang110136China

The effects of the erosion present on the leading edge of a wind turbine airfoil(DU 96-W-180)on its aerodynamic performances have been investigated numerically in the framework of a SST k–ωturbulence model based on the Reynolds Averaged Navier-Stokes equations(RANS).The results indicate that when sand-induced holes and small pits are involved as leading edge wear features,they have a minimal influence on the lift and drag coefficients of the ***,if delamination occurs in the same airfoil region,it significantly impacts the lift and resistance characteristics of the ***,as the angle of attack grows,there is a significant decrease in the lift coefficient accompanied by a sharp increase in the drag *** wear intensifies,these effects gradually ***,the leading edge wear can exacerbate flow separation near the trailing edge suction surface of the airfoil and cause forward displacement of the separation point.

关键词： Wind energy wind turbine erosion airfoil leading edge erosion characteristics aerodynamic performance numerical simulation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：