检索结果-南通市图书馆

Boosting cationic and anionic redox activity of Li-rich layered oxide cathodes via Li/Ni disordered regulation

Journal of Energy Chemistry 2025年第1期100卷 533-543页

作者： Zewen Liu Zhen Wu Hao Wang Xudong Zhang Yuanzhen Chen Yongning Liu Shengwu Guo Shenghua Chen Yanli Nan Yan Liu state key laboratory for mechanical behavior of materials Xi'an Jiaotong University school of materials Science and Engineering Xi'an University of Architecture and Technology Hefei Advanced Computing Center Operation Management Corp Ltd Network Information Center Xi'an Jiaotong University

Lithium-rich layered oxides （LLOs） are increasingly recognized as promising cathode materials for nextgeneration high-energy-density lithium-ion batteries （LIBs）.However,they suffer from voltage decay and low initial Coulombic efficiency （ICE） due to severe structural degradation caused by irreversible O ***,we introduce a three-in-one strategy of increasing Ni and Mn content,along with Li/Ni disordering and TM–O covalency regulation to boost cationic and anionic redox activity simultaneously and thus enhance the electrochemical activity of *** target material,Li1.2Ni0.168Mn0.558Co0.074O2（L1）,exhibits an improved ICE of 87.2%and specific capacity of 293.2 mA h g-1and minimal voltage decay of less than 0.53 m V cycle-1over 300 cycles at 1C,compared to Li1.2Ni0.13Mn0.54Co0.13O2（Ls）(274.4 mA h g-1for initial capacity,73.8%for ICE and voltage decay of 0.84 mV/cycle over 300 cycles at 1C).Theoretical calculations reveal that the density of states （DOS） area near the Fermi energy level for L1 is larger than that of Ls,indicating higher anionic and cationic redox reactivity than ***,L1 exhibits increased O-vacancy formation energy due to higher Li/Ni disordering of 4.76%（quantified by X-ray diffraction Rietveld refinement） and enhanced TM–O covalency,making lattice O release more difficult and thus improving electrochemical *** increased Li/Ni disordering also leads to more Ni2+presence in the Li layer,which acts as a pillar during Li+de-embedding,improving structural *** research not only presents a viable approach to designing low-Co LLOs with enhanced capacity and ICE but also contributes significantly to the fundamental understanding of structural regulation in high-performance LIB cathodes.

关键词： Ice

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Achieving ultralow leakage current in Schottky-MIS cascode anode lateral field-effect diode based on AlGaN/GaN HEMT

引用

Science China(Information Sciences) 2025年第1期68卷 379-385页

作者： Fangzhou WANG Changhong GAO Guojian DING Cheng YU Zhuocheng WANG Xiaohui WANG Qi FENG Ping YU Peng ZUO Wanjun CHEN Yang WANG Haiqiang JIA Hong CHEN Bo ZHANG Zeheng WANG Songshan Lake materials laboratory school of microelectronics Southern University of Science and Technology state key laboratory of Electronic Thin Films and Integrated Devices University of Electronic Science and Technology of China Manufacturing Commonwealth Scientific and Industrial Research Organisation

In this paper,we design and fabricate a Schottky-metal-insulator-semiconductor（MIS） cascode anode GaN lateral field-effect diode（CA-LFED） to achieve ultralow reverse leakage current(ILEAK).The device based on AlGaN/GaN highelectron-mobility-transistor（HEMT） includes a normally-off MIS-controlled channel that is cascoded with a high barrier height Schottky *** reverse bias,the high electric-field is effectively prevented by the normally-off MIS-controlled channel *** with the high barrier height Schottky contact,this feature significantly suppresses the *** by the device fabrication,the CA-LFED with high breakdown voltage（BV）>600 V shows an ultralow ILEAKof 3.6×10-9A/mm as well as a low forward voltage drop（VF） of 2.2 *** performance suggests that the CA-LFED can be a promising candidate for ultralow ILEAKand better VF-ILEAKtrade-off GaN power diode applications.

关键词： Schottky-MIS cascode anode lateral field-effect diode (LFED) ultralow reverse leakage current ($I_{\rm{LEAK}}$) forward drop and reverse leakage trade-off AlGaN/GaN HEMTs

来源：

同方期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Ultra‑High Sensitivity Anisotropic Piezoelectric Sensors for Structural Health Monitoring and Robotic Perception

引用

Nano-Micro Letters 2025年第2期17卷 432-446页

作者： Hao Yin Yanting Li Zhiying Tian Qichao Li Chenhui Jiang Enfu Liang Yiping Guo state key laboratory of Metal Matrix Composites School of Materials Science and EngineeringShanghai Jiao Tong UniversityShanghai 200240People’s Republic of China Beijing Vacuum Electronics Research Institute Beijing 100015People’s Republic of China Fundamental Science On Vibration Shock and Noise LaboratoryState Key Laboratory of Mechanical System and VibrationSchool of Mechanical EngineeringShanghai Jiao Tong UniversityShanghai 200240People’s Republic of China

Monitoring minuscule mechanical signals,both in magnitude and direction,is imperative in many application scenarios,e.g.,structural health monitoring and robotic sensing ***,the piezoelectric sensor struggles to satisfy the requirements for directional recognition due to the limited piezoelectric coefficient matrix,and achieving sensitivity for detecting micrometer-scale deformations is also ***,we develop a vector sensor composed of lead zirconate titanate-electronic grade glass fiber composite filaments with oriented arrangement,capable of detecting minute anisotropic *** as-prepared vector sensor can identify the deformation directions even when subjected to an unprecedented nominal strain of 0.06%,thereby enabling its utility in accurately discerning the 5μm-height wrinkles in thin films and in monitoring human pulse *** ultra-high sensitivity is attributed to the formation of porous ferroelectret and the efficient load transfer efficiency of continuous lead zirconate titanate ***,when integrated with machine learning techniques,the sensor’s capability to recognize multi-signals enables it to differentiate between 10 types of fine textures with 100%*** structural design in piezoelectric devices enables a more comprehensive perception of mechanical stimuli,offering a novel perspective for enhancing recognition accuracy.

关键词： Flexible piezoelectric filaments Anisotropic Ultra-high sensitivity Structural health detection Texture recognition

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Defects‑Rich Heterostructures Trigger Strong Polarization Coupling in Sulfides/Carbon Composites with Robust Electromagnetic Wave Absorption

引用

Nano-Micro Letters 2025年第1期17卷 528-547页

作者： Jiaolong Liu Siyu Zhang Dan Qu Xuejiao Zhou Moxuan Yin Chenxuan Wang Xuelin Zhang Sichen Li Peijun Zhang Yuqi Zhou Kai Tao Mengyang Li Bing Wei Hongjing Wu Mengyang Li Bing Wei Hongjing Wu school of Physics Xidian UniversityXi’an 710071People’s Republic of China school of Advanced materials and Nanotechnology State Key Discipline Laboratory of Wide Band Gap Semiconductor TechnologyXidian UniversityXi’an 710071People’s Republic of China school of microelectronics Xidian UniversityXi’an 710071People’s Republic of China school of Telecommunication Engineering Xidian UniversityXi’an 710071People’s Republic of China MOE key laboratory of Material Physics and Chemistry Under Extraordinary School of Physical Science and TechnologyNorthwestern Polytechnical UniversityXi’an 710072People’s Republic of China The Ministry of Education key laboratory of Micro and Nano Systems forAerospace School of Mechanical EngineeringNorthwestern PolytechnicalUniversityXi’an 710072People’s Republic of China

Defects-rich heterointerfaces integrated with adjustable crystalline phases and atom vacancies,as well as veiled dielectric-responsive character,are instrumental in electromagnetic *** methods,however,constrain their delicate ***,an innovative alternative is proposed:carrageenan-assistant cations-regulated(CACR)strategy,which induces a series of sulfides nanoparticles rooted in situ on the surface of carbon *** unique configuration originates from strategic vacancy formation energy of sulfides and strong sulfides-carbon support interaction,benefiting the delicate construction of defects-rich heterostructures in M_(x)S_(y)/carbon composites(M-CAs).Impressively,these generated sulfur vacancies are firstly found to strengthen electron accumulation/consumption ability at heterointerfaces and,simultaneously,induct local asymmetry of electronic structure to evoke large dipole moment,ultimately leading to polarization coupling,i.e.,defect-type interfacial ***“Janus effect”(Janus effect means versatility,as in the Greek two-headed Janus)of interfacial sulfur vacancies is intuitively confirmed by both theoretical and experimental investigations for the first ***,the sulfur vacancies-rich heterostructured Co/Ni-CAs displays broad absorption bandwidth of 6.76 GHz at only 1.8 mm,compared to sulfur vacancies-free CAs without any dielectric *** defects-rich heterostructures,this one-pot CACR strategy may steer the design and development of advanced nanomaterials,boosting functionality across diverse application domains beyond electromagnetic response.

关键词： Defects-rich heterointerfaces Sulfides Polarization coupling Electromagnetic wave absorption

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Bioinspired Passive Tactile Sensors Enabled by Reversible Polarization of Conjugated Polymers

引用

Nano-Micro Letters 2025年第1期17卷 361-377页

作者： Feng He Sitong Chen Ruili Zhou Hanyu Diao Yangyang Han Xiaodong Wu school of mechanical Engineering Sichuan UniversityChengdu 610065People’s Republic of China school of Software Engineering Chongqing University of Posts and TelecommunicationsChongqing 400065People’s Republic of China state key laboratory of Polymer materials Engineering Sichuan UniversityChengdu 610065People’s Republic of China

Tactile perception plays a vital role for the human body and is also highly desired for smart prosthesis and advanced *** to active sensing devices,passive piezoelectric and triboelectric tactile sensors consume less power,but lack the capability to resolve static ***,we address this issue by utilizing the unique polarization chemistry of conjugated polymers for the first time and propose a new type of bioinspired,passive,and bio-friendly tactile sensors for resolving both static and dynamic ***,to emulate the polarization process of natural sensory cells,conjugated polymers(including poly(3,4-ethylenedioxythiophen e):poly(styrenesulfonate),polyaniline,or polypyrrole)are controllably polarized into two opposite states to create artificial potential *** controllable and reversible polarization process of the conjugated polymers is fully in situ ***,a micro-structured ionic electrolyte is employed to imitate the natural ion channels and to encode external touch stimulations into the variation in potential difference *** with the currently existing tactile sensing devices,the developed tactile sensors feature distinct characteristics including fully organic composition,high sensitivity(up to 773 mV N^(−1)),ultralow power consumption(nW),as well as superior *** demonstrations,both single point tactile perception(surface texture perception and material property perception)and two-dimensional tactile recognitions(shape or profile perception)with high accuracy are successfully realized using self-defined machine learning *** tactile sensing concept innovation based on the polarization chemistry of conjugated polymers opens up a new path to create robotic tactile sensors and prosthetic electronic skins.

关键词： Passive tactile sensors Reversible polarization of conjugated polymers Tactile perception Machine learning algorithm Object recognition

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of pouring time on microstructure and mechanical properties of centrifugal cast Ti-46Al alloy tubes

引用

China Foundry 2025年

作者： Gang Huang Qian Dang Cong-cong Su Jing Zhao Chi Zhang Guo-huai Liu Zhao-dong Wang The state key laboratory of Rolling and Automation Northeastern University school of materials Science and Engineering Shenyang University of Technology

The grain size of TiAl alloy castings prepared by traditional casting process is coarse, thus showing poor mechanical properties. In this study, a new type of high performance Ti-46Al alloy tube prepared by vacuum centrifugal casting technology was introduced. This research comprehensively examined the influence of pouring time on the microstructure and mechanical performance of the castings, employing both experimental approaches and ProCast simulation methodologies. The findings indicate that prolonging the pouring time facilitates a microstructural evolution from coarse columnar grains to refined equiaxed grains. Under the condition of pouring temperature of 1,600 °C, rotation speed of 800 r·min-1and pouring time of 6 s, the tensile strength of Ti-46Al alloy at room temperature reaches 650 MPa, and the tensile strength at 800 °C reaches 705 MPa, which is significantly higher than that of traditional as-cast Ti-Al alloy.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Innovative dual-mode device integrating capacitive desalination and solar vapor generation for high-efficiency seawater desalination

引用

Journal of Energy Chemistry 2025年第1期100卷 171-179页

作者： Jiacheng Wang Zhaoyu Chen Ruduan Yuan Jiaxin Luo Ben Zhang Keju Ji Meng Li Juanxiu Xiao Kuan Sun National Innovation Center for Industry-Education Integration of Energy Storage Technology MOE Key Laboratory of Low-grade Energy Utilization Technologies and SystemsCollege of Energy & Power Engineering Chongqing University Xuefeng Mountain Energy Equipment Safety National Observation and Research Station CQU-NUS Renewable Energy Materials & Devices Joint Laboratory Chongqing University Southwest Technology and Engineering Research Institute Jiangsu Provincial key laboratory of Bionic Functional materials College of Mechanical and Electrical Engineering Nanjing University of Aeronautics and Astronautics state key laboratory of Marine Resources Utilization in South China Sea Collaborative Innovation Center of Marine Science and Technology School of Marine Science and Engineering Hainan University

Solar-driven interface evaporation with high solar-to-steam conversion efficiency has shown great potential in seawater ***,due to the influence of latent heat and condensation efficiency,the water yield from solar-driven interface evaporation remains insufficient,posing a significant challenge that requires *** this work,we designed a dual-mode high-flux seawater desalination device that combines solar-driven interface evaporation and capacitive *** utilizing coupled desalination materials exhibiting both photothermal conversion and capacitance activity,the device demonstrated photothermal evaporation rates of 1.41 and 0.97 kg m-2h-1for condensate water yield under one-sun ***,the device exhibited a salt adsorption capacity of up to48 mg g-1and a salt adsorption rate of 2.1 mg *** addition,the salt adsorption capacity increased by approximately 32% under one-sun ***,photo-enhanced capacitive desalination performance was explored through numerical simulations and theoretical *** calculations and characterizations confirmed that the defect energy levels formed by the introduction of sulfur vacancies can effectively widen the light absorption range,improve photothermal conversion performance,and stimulate more photoelectrons to participate in capacitive ***,the electron distribution state of molybdenum disulfide with sulfur vacancies and surface defect sites contributes to ion/electron transport at the solid-liquid *** work provides a novel pathway for integrating solar vapor generation with other low-energy desalination technologies.

关键词： Desalination

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Polybenzimidazolium-reinforced polyimide separators to inhibit dendrites for high-security lithium-ion batteries

引用

Science China Chemistry 2025年

作者： Guohua Sun Jiaqi Cui Qingsong Zhang Yisong Zhou Xinluo Li Yingying Zhang Zhanao Zhang Xin Zhang Jiantao Fan Pengpeng Li Lianlong Hou Nanjun Chen Hebei key laboratory of Flexible Functional materials School of Materials Science and Engineering Hebei University of Science and Technology state key laboratory of Organic-Inorganic Composites Beijing University of Chemical Technology Academy for Advanced Interdisciplinary Studies Southern University of Science and Technology state key laboratory of Physical Chemistry of Solid Surfaces College of Chemistry and Chemical Engineering Xiamen University

Lithium dendrite formation poses a significant safety hazard in lithium-ion batteries（LIBs）, severely impeding their widespread adoption and further technological advancements. Here, we present a novel quaternized polybenzimidazolium（q-PBI） to armor polyimide（PI） nanofiber separator（q-PBI@PI）, in which the q-PBI containing lithiophilicity and anionphilicity sites serves as the multifunctional nano-layers to suppress the Li dendrite and reinforce the mechanical properties of PI nanofiber ***, the q-PBI@PI separator displays an unprecedented mechanical strength of 82.8 MPa, significantly outperforming previously reported PI nanofiber membranes（typically below 50.0 MPa）. Besides, we demonstrate that the q-PBI@PI separator simultaneously possesses low nucleation overpotential（59 mV） and exceptional average coulombic efficiency due to the suppression of Li dendrite. Importantly, q-PBI@PI-based Li||Li battery enables a stable Li plating-stripping at 1.0 m A cm-2for600 h. Attributing to these exceptional merits, the armored PI separator-based LIBs display remarkable specific capability and capacity retention. The density function theory calculations reveal that q-PBI is conducive to the desolvation of Li+and can immobilize Li+and PF6-ions near affinity sites of PI nanofibers for inhibiting the formation of Li dendrites. Our work paves a new avenue for the design of next-generation high-performing separators in LIBs.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Advances in Graphene‑Based Electrode for Triboelectric Nanogenerator

引用

Nano-Micro Letters 2025年第1期17卷 378-403页

作者： Bin Xie Yuanhui Guo Yun Chen Hao Zhang Jiawei Xiao Maoxiang Hou Huilong Liu Li Ma Xin Chen Chingping Wong state key laboratory of Precision Electronic Manufacturing Technology and Equipment Guangdong University of TechnologyGuangzhou 510006People’s Republic of China school of Electromechanical Engineering Guangdong University of TechnologyGuangzhou 510006People’s Republic of China school of materials Science and Engineering Georgia Institute of TechnologyAtlantaGA 30332USA

With the continuous development of wearable electronics,wireless sensor networks and other micro-electronic devices,there is an increasingly urgent need for miniature,flexible and efficient nanopower generation *** nanogenerator(TENG)technology can convert small mechanical energy into electricity,which is expected to address this *** the core component of TENG,the choice of electrode materials significantly affects its *** metal electrode materials often suffer from problems such as durability,which limits the further application of ***,as a novel electrode material,shows excellent prospects for application in TENG owing to its unique structure and excellent electrical *** review systematically summarizes the recent research progress and application prospects of TENGs based on graphene *** precision processing methods of graphene electrodes are introduced,and the applications of graphene electrode-based TENGs in various scenarios as well as the enhancement of graphene electrodes for TENG performance are *** addition,the future development of graphene electrode-based TENGs is also prospectively discussed,aiming to promote the continuous advancement of graphene electrode-based TENGs.

关键词： Triboelectric nanogenerator Precision processing Graphene electrode Self-powered sensor

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Spontaneous Orientation Polarization of Anisotropic Equivalent Dipoles Harnessed by Entropy Engineering for Ultra‑Thin Electromagnetic Wave Absorber

引用

Nano-Micro Letters 2025年第1期17卷 424-438页

作者： Honghan Wang Xinyu Xiao Shangru Zhai Chuang Xue Guangping Zheng Deqing Zhang Renchao Che Junye Cheng Liaoning key Lab of Lignocellulose Chemistry and Biomaterials Liaoning Collaborative Innovation Center for Lignocellulosic BiorefinerySchool of Light Industry and Chemical EngineeringDalian Polytechnic UniversityDalian 116034People’s Republic of China school of Life Science and Biotechnology Dalian University of TechnologyDalian 116024People’s Republic of China Department of mechanical Engineering Hong Kong Polytechnic UniversityHung HomKowloonHong Kong 999077People’s Republic of China school of materials Science and Engineering Qiqihar UniversityQiqihar 161006People’s Republic of China laboratory of Advanced materials Shanghai Key Lab of Molecular Catalysis and Innovative MaterialsAcademy for Engineering&TechnologyFudan UniversityShanghai 200438People’s Republic of China Department of materials Science Shenzhen MSU-BIT UniversityShenzhen 517182People’s Republic of China

The synthesis of carbon supporter/nanoscale high-entropy alloys(HEAs)electromagnetic response composites by carbothermal shock method has been identified as an advanced strategy for the collaborative competition engineering of conductive/dielectric *** migration modes within HEAs as manipulated by the electronegativity,valence electron configurations and molar proportions of constituent elements determine the steady state and efficiency of equivalent ***,enlightened by skin-like effect,a reformative carbothermal shock method using carbonized cellulose paper(CCP)as carbon supporter is used to preserve the oxygencontaining functional groups(O·)of carbonized cellulose fibers(CCF).Nucleation of HEAs and construction of emblematic shell-core CCF/HEAs heterointerfaces are inextricably linked to carbon metabolism induced by O·.Meanwhile,the electron migration mode of switchable electronrich sites promotes the orientation polarization of anisotropic equivalent *** virtue of the reinforcement strategy,CCP/HEAs composite prepared by 35%molar ratio of Mn element(CCP/HEAs-Mn_(2.15))achieves efficient electromagnetic wave(EMW)absorption of−51.35 dB at an ultra-thin thickness of 1.03 *** mechanisms of the resulting dielectric properties of HEAs-based EMW absorbing materials are elucidated by combining theoretical calculations with experimental characterizations,which provide theoretical bases and feasible strategies for the simulation and practical application of electromagnetic functional devices(e.g.,ultra-wideband bandpass filter).

关键词： High-entropy alloys Carbothermal shock Switchable electron migration modes Emblematic shell-core heterointerfaces Ultra-thin thickness

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：