检索结果-南通市图书馆

Chinese Chemical Letters 2024年第8期35卷 433-436页

作者： Peng Zhou Ziang Jiang Yang Li Peng Xiao Feixiang Wu Powder metallurgy Research Institute School of Metallurgy and EnvironmentCentral South UniversityChangsha 410083China

Sulphur(S)-template method based on conventional slurry-casting method has been developed to pro-duce porous silicon(Si)*** facile fabrication technology is suitable for current production line and expected to be widely applied to various electrode materials under large volume change during ***,S particles as template agent are mixed with active material Si,carbon conductor and binder forming uniform *** casting and drying,the electrodes are immersed in carbon disul-fide solution to remove S particles rapidly,generating pores in-situ at the original position of S *** analysis shows that the pores inside electrodes are able to shorten lithium ion diffusion paths,reduce normal expansion rate and decrease formation of cracks in the Si electrode(2 mg_(Si)/cm^(2)),demonstrating a reversible capacity of 951 mAh/g at 0.5 A/g after 100 cycles(with a capacity retention of 99.5%)and a capacity of-826 mAh/g at 2 A/g.

关键词： Sulphur-template Porous electrodes Silicon anodes Low volume expansion Lithium-ion batteries

Efficient recovery of tungsten from scheelite concentrates using a sulfur-phosphorus mixed acid leaching system

在线全文

学校读者我要写书评

暂无评论

Tungsten 2024年第4期6卷 821-832页

作者： Jiang-Tao Li Li-Li Gao Zhong-Wei Zhao Xu-Heng Liu Xing-Yu Chen school of metallurgy and environment Central South University Key Laboratory of Hunan Province for metallurgy and Material Processing of Rare Metals

In recent years,a new process for leaching scheelite concentrates with sulfur-phosphorus mixed acid has been successfully *** process suffers from the elimination of the retarding effect of calcium sulfate,the selective extraction of tungsten from the H3PW12O40-H2SO4-H3PO4mixture solution,and the removal of introduced ***,in this paper,we investigated the inhibition measures of a calcium sulfate-blocking membrane,the selective extraction of tungsten by ion exchange,and the removal of phosphorus by the magnesium ammonium salt *** results showed that the addition of calcium sulfate whisker seeds and a higher H3PO4concentration inhibited spontaneous diffuse nucleation,promoted crystal growth,and avoided the formation of a dense blocking *** 98 wt.% of the scheelite concentrate was digested by *** selective adsorption of PW12O403-was realized using D301 resin,and the extraction efficiency of tungsten exceeded 99.9%.After desorption with ammonia water,PW12O403-was depolymerized into WO42-and PO43-.99.9 wt.% of phosphorus was removed in the form of MgNH4PO4by the magnesium ammonium salt method,and the residual phosphorus concentration in the solution was lower than 10 mg·*** purification,the highest-grade ammonium paratungstate product was prepared by evaporative crystallization.

关键词： Calcium sulfate Ion exchange Scheelite concentrates Sulfur-phosphorus mixed acid Tungsten

Straw addition increases enzyme activities and microbial carbon metabolism activities in bauxite residue

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Journal of environmental Sciences 2024年第1期135卷 332-344页

作者： Hao Wu Wei Sun Feng Zhu Yifan Jiang Shiwei Huang Johnvie Goloran Shengguo Xue school of Minerals Processing and Bioengineering Central South UniversityChangsha 410083China school of metallurgy and environment Central South UniversityChangsha 410083China school of environment and Science Griffith UniversityBrisbaneQLD 4072Australia

Recovery of microbial functions is one of the critical processes in the nutrient cycling of bauxite residue for improving *** is considered to be effective to increase microbial diversity and drive the development of the microbial community,but its effect on microbial carbon metabolism has not been *** present study evaluated the effects of phosphogypsum(PG),straw(SF)and phosphogypsum plus straw(PGSF)on physicochemical properties,enzyme activities,and microbial carbon metabolism activities in bauxite *** 180 days incubation,PG,SF and PGSF treatment significantly reduced the residue pH from 10.85 to 8.64,9.39 and 8.06,*** to CK treatment,SF treatment significantly increased the content of total organic carbon(TOC)and organic carbon fractions(DOC,MBC,EOC,and POC).In addition,straw addition significantly increased glucosidase,cellulose,urease,and alkaline phosphatase by 7.2-9.1 times,5.8-7.1 times,11.1-12.5 times,and 1.1-2.2 times,*** Biolog results showed that straw addition significantly increased microbial metabolic activity(AWCD)and diversity in bauxite *** analysis indicated total nitrogen(TN)and carbon fractions(POC,MBC and DOC)were the most important environmental factors affecting microbial metabolic activity and diversity in bauxite *** findings provided us with a biogeochemical perspective to reveal soil formation in bauxite residue and suggested that nutrient supplement and regulation of salinity-alkalinity benefit the establishment of microbial communities and functions in bauxite residue.

关键词： Bauxite residue Labile organic carbon fractions Enzyme activities Community-level physiological profiles Soil formation in bauxite residue

A simple route for preparation of TRIP-assisted Si-Mn steel with excellent performance using direct strip casting

在线全文

学校读者我要写书评

暂无评论

International Journal of Minerals,metallurgy and Materials 2024年第10期31卷 2173-2181页

作者： Hui Xu Lejun Zhou Wanlin Wang Yang Yi school of metallurgy and environment Central South UniversityChangsha 410083China National Center for International Research of Clean metallurgy Central South UniversityChangsha 410083China

The complex producing procedures and high energy-consuming limit the large-scale production and application of advanced high-strength steels(AHSSs).In this study,the direct strip casting(DSC)technology with unique sub-rapid solidification characteristics and cost advantages was applied to the production of low-alloy Si-Mn steel with the help of quenching&partitioning(Q&P)concept to address these *** this method with the conventional compact strip production(CSP)process,the initial microstructure formed under different solidification conditions and the influence of heat treatment processes on the final mechanical properties were *** results show that the initial structure of the DSC sample is a dual-phase structure composed of fine lath martensite and bainite,while the initial structure of the CSP sample consists of pearlite and *** volume fraction and carbon content of retained austenite(RA)in DSC samples are usually higher than those in CSP samples after the same Q&P *** samples typically demonstrate better comprehensive mechanical properties than the CSP *** DSC sample partitioned at 300℃ for 300 s(DSC-Pt300)achieves the best comprehensive mechanical properties,with yield strength(YS)of 1282 MPa,ultimate tensile strength(UTS)of 1501 MPa,total elongation(TE)of 21.5%,and product of strength and elongation(PSE)as high as 32.3 GPa·%.These results indicate that the excellent mechanical properties in low-alloy Si-Mn steel can be obtained through a simple process(DSC-Q&P),which also demonstrates the superiority of DSC technology in manufacturing AHSSs.

关键词： direct strip casting sub-rapid solidification quenching and partitioning TRIP-assisted AHSSs microstructure

Effect of phosphorus content on interfacial heat transfer and film deposition behavior during the high-temperature simulation of strip casting

在线全文

学校读者我要写书评

暂无评论

International Journal of Minerals,metallurgy and Materials 2024年第5期31卷 1016-1025页

作者： Wanlin Wang Cheng Lu Liang Hao Jie Zeng Lejun Zhou Xinyuan Liu Xia Li Chenyang Zhu school of metallurgy and environment Central South UniversityChangsha 410083China National Center for International Research of Clean metallurgy Central South UniversityChangsha 410083China Institute of Research of Iron and Steel ShasteelJiangsu ProvinceZhangjiagang 215625China

The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification technique with the aims to reveal the effects of phosphorus content on interfacial wettability,deposited film,and interfacial heat transfer *** showed that when the phosphorus content increased from 0.014wt%to 0.406wt%,the mushy zone enlarged,the complete solidification temperature delayed from1518.3 to 1459.4℃,the final contact angle decreased from 118.4°to 102.8°,indicating improved interfacial contact,and the maximum heat flux increased from 6.9 to 9.2 MW/*** the phosphorus content from 0.081wt%to 0.406wt%also accelerated the film deposition rate from 1.57 to 1.73μm per test,resulting in a thickened naturally deposited film with increased thermal resistance that advanced the transition point of heat transfer from the fifth experiment to the third experiment.

关键词： strip casting interfacial heat transfer interfacial wettability naturally deposited film phosphorus content

Evolution of interfacial heat transfer,contact behavior and microstructure during sub-rapid solidification of molten steel with different hydrogen contents

在线全文

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第1期31卷 215-223页

作者： Cheng Lu Wan-lin Wang Chen-yang Zhu Jie Zeng Xin-yuan Liu Hua-long Li school of metallurgy and environment Central South UniversityChangsha410083HunanChina National Center for International Research of Clean metallurgy Central South UniversityChangsha410083HunanChina Institute of Research of Iron and Steel ShasteelZhangjiagang215625JiangsuChina

Typical Q235 low-carbon steel samples with different hydrogen contents(0.0004,0.0008,and 0.0013 wt.%)were prepared by adjusting the environment humidity and *** effects of hydrogen on interfacial heat transfer,contact behavior,and microstructure evolution were investigated using a novel droplet solidification *** results revealed that when the hydrogen content increases from 0.0004 to 0.0013 wt.%,the maximum heat flux between the molten steel and cooling substrate decreases from 8.01 to 6.19 MW/m^(2),and the total heat removed in the initial 2 s reduces from 10.30 to 8.27 MJ/m^(2).Moreover,the final contact angle between the molten steel and substrate increases from 103.741°to 113.697°,and the number of pores on the droplet bottom surface increases significantly from 21 to 210 with the increase in *** surface roughness of the droplet bottom surface increases from 20.902 to 49.181 *** addition,the average grain size of the droplet increases from 14.778 to 33.548 pm with the increase in the hydrogen *** interfacial contact condition becomes worse due to the escape of hydrogen from the steel matrix during the cooling process,which leads to the reduction in the interfacial heat transfer and the increase in the grain size.

关键词： Strip casting Hydrogen content Interfacial heat transfer behavior Contact behavior Microstructure evolution

CFD-DEM study on the synergistic effect of coke consumption and particle dynamics in the blast furnace raceway

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Particuology 2024年第6期89卷 270-278页

作者： Peng Xu Peng Han Zhijun He Xizhong An Kang Sun Lihua Gao Key Laboratory of Green Low-Carbon and Intelligent metallurgy School of Materials and MetallurgyUniversity of Science and Technology LiaoningAnshan 114000China Key Laboratory for Ecological metallurgy of Multimetallic Mineral of Ministry of Education School of MetallurgyNortheastern UniversityShenyang110819China

In this study,the gas-solid flow process in the blast furnace raceway is numerically simulated using coupled computational fluid dynamics and the discrete element method(CFD-DEM).The coke reaction kinetics data are imported into the DEM model to reproduce the consumption process of each coke *** effects of inlet gas velocity and angle on the morphology of the raceway,coke consumption rate,coke bed temperature,and particle size distribution in the blast process are systematically investigated and *** results show that the consumption of coke particles promotes the formation of raceways during the blast *** the same time,a coke mixture layer is produced at the edge of the *** higher the inlet gas velocity,the thicker the coke mixture layer in the middle and upper parts of the raceway region,and the larger the proportion of small particles in the coke mixture *** effect of the inlet gas angle on the raceway region is less than the inlet gas ***,with the increase in the inlet gas angle,the high-temperature region of the coke bed extends downward gradually,which is conducive to activating the hearth.

关键词： Blast furnace Raceway Multiphase flow CFD-DEM Modeling

Revealing the stability origins of 596 days-humidity-stable semitransparentperovskite solar cells

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Energy Chemistry 2024年第7期94卷 208-216页

作者： Tian Chen Ying Yang Congtan Zhu Weihuang Lin Qilin Dai Xueyi Guo school of metallurgy and environment Central South UniversityChangsha 410083HunanChina Department of Chemistry Physics and Atmospheric SciencesJackson State UniversityJacksonMS 39217USA

Hybrid organic-inorganic perovskites(HOIPs)hold promise in the field of optoelectronics due to their excellent photoelectric conversion ***,the ion migration and hygroscopicity of these perovskite solar cells need to be ***,we presented semitransparent perovskite solar cells(ST-PSCs)using hole transport layer(HTL)combined with polyaniline(PANI)to stabilize HTL/perovskite interface,achieving a humidity durability(RH,50%-90%)for 596 days(14304 h)without ***,the decrease in hydrolysis products(LiF)showed the interaction between PANI with the addi-tives in HTL dramatically inhibited the water uptake and corrosion on MAPbI_(3),*** PANI modified samples had a higher I/Pb ratio and lower trap state density,which indicated the passivation effect of PANI on the uncoordinated Pb^(2+)and iodine ***,PANI successfully stabilized the interface and perovskite by inhibiting the formation of Pb^(0) and Au migration as long period *** work presented an interfacial design to develop HOiP in air with high humidity stability.

关键词： HTL/perovskite interface Polyaniline-passivation Humidity-degradation mechanism lon migration

Suppressed Internal Intrinsic Stress Engineering in High-Performance Ni-Rich Cathode Via Multilayered In Situ Coating Structure

在线全文

学校读者我要写书评

暂无评论

Energy & environmental Materials 2024年第2期7卷 62-70页

作者： Jiachao Yang Yunjiao Li Xiaoming Xi Junchao Zheng Jian Yu Zhenjiang He school of metallurgy and environment Central South University Engineering Research Center of the Ministry of Education for Advanced Battery Materials Central South University Changsha Research Institute of Mining and metallurgy Ningbo Ronbay New Energy Technol Co Ltd

LiNixCoyAlzO2（NCA） cathode materials are drawing widespread attention,but the huge gap between the ideal and present cyclic stability still hinders their further commercial application,especially for the Ni-rich LiNixCoyAlzO2（x>0.8,x+y+z=1） cathode material,which is owing to the structural degradation and particles' intrinsic *** tackle the problems,Li0.5La2Al0.5O4in situ coated and Mn compensating doped multilayer LiNi0.82Co0.14Al0.04O2was *** refinement indicates that La-Mn comodifying could realize appropriate Li/Ni disorder *** results and in situ XRD patterns reveal that the LLAO coating layer could effectively restrain crack in secondary particles benefited from the suppressed internal *** further improves as NCA-LM2 has superior mechanical *** SEM,TEM,XPS tests indicate that the cycled cathode with LLAO-Mn modification displays a more complete morphology and less side reaction with *** was used to further investigate cathode-electrolyte interface which was reflected by gas ***-LM2 releases less CO2than NCA-P indexing on a more stable *** modified material presents outstanding capacity retention of 96.2% after 100 cycles in the voltage range of 3.0-4.4 V at 1C,13% higher than that of the pristine and80.8% at 1 C after 300 *** excellent electrochemical performance could be attributed to the fact that the high chemically stable coating layer of Li0.5La2Al0.5O4（LLAO） could enhance the interface and the Mn doping layer could suppress the influence of the lattice mismatch and *** believe that it can be a useful strategy for the modification of Ni-rich cathode material and other advanced functional material.

关键词： compensating doped in situ coating multilayer material Ni-rich cathode materials suppressed internal strain

Single-phase evolution path to new record efficiency of kesterite solar cells

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Science China Chemistry 2024年第2期67卷 420-421页

作者： Yixiong Ji Fangyang Liu school of metallurgy and environment Central South UniversityChangsha410083China ARC Centre of Excellence in Exciton Science School of ChemistryUniversity of Melbourne3010MelbourneVictoriaAustralia

Over the past few years, there have been significant advancements in uncovering previously sealed records in the kesterite solar cell. This also has led to substantial growth marked by multiple groups achieving successive efficiency breakthroughs, shining a renewed spotlight on this promising photovoltaic material that had previously been overlooked due to its low efficiency.

关键词： breakthrough sealed successive