检索结果-南通市图书馆

Journal of Materials Science & Technology 2019年第11期35卷 2600-2607页

作者： Qing Liu Guofeng Wang Xiaochong Sui Yongkang Liu Xiao Li Jianlei Yang national key laboratory for precision hot processing of metals Harbin Institute of Technology

The MoNbTaTiV refractory high-entropy alloy(RHEA)with ultra-fine grains and homogeneous microstructure was successfully fabricated by mechanical alloying(MA)and spark plasma sintering(SPS).The microstructural evolutions,mechanical properties and strengthening mechanisms of the alloys were systematically *** nanocrystalline mechanically alloyed powders with simple bodycentered cubic(BCC)phase were obtained after 40 h MA ***,the powders were sintered using SPS in the temperature range from 1500℃to 1700℃.The bulk alloys were consisted of submicron scale BCC matrix and face-centered cubic(FCC)precipitation *** bulk alloy sintered at 1600℃had an average grain size of 0.58μm and an FCC precipitation phase of 0.18μm,exhibiting outstanding micro-hardness of 542 HV,compressive yield strength of 2208 MPa,fracture strength of 3238 MPa and acceptable plastic strain of 24.9%at room *** enhanced mechanical properties of the MoNbTaTiV RHEA fabricated by MA and SPS were mainly attributed to the grain boundary strengthening and the interstitial solid solution *** is expectable that the MA and SPS processes are the promising methods to synthesize ultra-fine grains and homogenous microstructural RHEA with excellent mechanical properties.

关键词： Refractory high-entropy alloy Ultra-fine grain Mechanical alloying Spark plasma sintering Mechanical properties

Decomposition of Nb_(3)Si and mechanical-property improvement by adding appropriate amount of MgO in Nb-16Si-20Ti alloy

在线全文

学校读者我要写书评

暂无评论

Rare metals 2023年第4期42卷 1306-1315页

作者： De-Zhi Chen Qi Wang Rui-Run Chen Shu Wang Yan-Qing Su Heng-Zhi Fu national key laboratory for precision hot processing of metals Harbin Institute of TechnologyHarbin150001China

Five Nb-16Si-20Ti-xMgO alloys(x=0,0.1,0.5,1.0 and 3.0)were prepared via arc melting in this study,and the effect of MgO addition on their phase composition,microstructure evolution,and mechanical properties was *** results demonstrated that MgO reacted with the Nb-Si-Ti alloy while Mg atoms replaced Nb atoms in the Nbss *** hypoeutectic alloy was transformed into a hypereutectic alloy upon the addition of 3.0 at%MgO,and the Nb_(3)Si phases decomposed into a fine Nbss/α-Nb5Si3 eutectic *** highest fracture toughness was achieved for the Nb-16Si-20Ti-3MgO alloy,with an ambient fracture toughness value of 9.4 MPa·m^(-1/2)due to its largest Nbss phase content and optimal Nbss/α-Nb_(5)Si_(3)eutectic ***,the alloy compressive strength increased with MgO *** compressive strength of the Nb-16Si-20Ti-3MgO alloy was 2624.1 MPa,26.0%higher than that of Nb-16Si-20Ti,due to the formation of a solid solution of Mg atoms in the Nbss phase and reinforcement of a small amount of the Ti_(2)O ***,an increase in the content of the Nbss/α-Nb_(5)Si_(3)eutectic structure increased both the alloy strength and fracture strain.

关键词： Niobium silicon alloy Magnesium oxide Eutectic structure Fracture toughness

Mechanism and morphology evolution of the O phase transformation in Ti-22Al-25Nb alloy

在线全文

学校读者我要写书评

暂无评论

Journal of Materials Science & Technology 2021年第30期89卷 97-106页

作者： Zong Yingying Wang Jiwei Shao Bin Tang Wei Shan Debin national key laboratory for precision hot processing of metals Harbin Institute of TechnologyHarbin150001China

The phase transformation and microstructure in Ti-22Al-25Nb alloy are extremely *** this work,the morphology evolution of the O phase during the heating and cooling process was investigated by electron backscatter diffraction(EBSD)and first-principles *** results show that the O→α_(2)phase transformation process during the heating process is as follows:spheroidization of the O phase occurs first,then theα_(2)phase nucleates in the spheroidized O phase,grows and replaces the O phase,completing the O→α_(2)phase *** the meanwhile,the diffusion of Nb from Nb-poor O to Nb-rich B2 phases is a back-diffusion *** to first-principles calculations,the driving force of the O→α_(2)phase transformation is the difference in the free energies of formation for the two phases(0.09 eV/atom).When the Nb content is greater than 15.625%,the lattice distortion of theα_(2)phase sharply increases,and the distortion energy drives the back-diffusion of *** the cooling process,theα_(2)→O phase transformation is difficult and slow due to the difficult diffusion of Nb from the B2 toα_(2)*** holding for 60 min at 960℃,the coarseα_(2)phase gradually transforms to the O phase from the margin to the inside,forming a dispersed mixed structure of the O andα_(2)*** the B2→O transformation,the nucleation of the O phase induces a high stress region,in the range of approximately 200 nm.

关键词： Ti-22Al-25Nb alloy Phase transformation Microstructure O phase First-principles

Microstructure and mechanical properties of surface layers of 30CrMnSiA steel plasma nitrocarburized with rare earth addition

在线全文

学校读者我要写书评

暂无评论

Journal of Rare Earths 2012年第12期30卷 1281-1286页

作者：唐丽娜闫牧夫 national key laboratory for precision hot processing of metals School of Materials Science and EngineeringHarbin Institute of Technology

The pulse plasma nitrocarburizing for 30CrMnSiA steel was conducted at 560 ℃ for 8 h in mixed gases of N2：3H2 and different flow rates of rare earths （RE） addition. Effects of rare earths （RE） addition in the carrier gas on the surface morphology, phase structure and mechanical properties of the nitrocarburized layer were characterized by optical microscopy （OM）, X-ray diffraction （XRD）, scanning electron microscopy （SEM）, microhardness testing and wear testing, respectively. The results showed that the surface phase structures changed from dual phases ε-Fe2.3N（C） and γ′-Fe4N（C） to phase Fe3C and incipient nitrides, and the nitrocarburized surface hardness value decreased slightly from 756 to 681 HV0.1 with the RE addition increasing in the cartier gas, and the corresponding morphology of the nitrocarburized surface was granular nitride group （diameter 0.8-1.5 μm） and compact-fine Fe3C stick and patch （mean size 100-300 nm）, respectively. The wear resistance of the experimental steel could be improved remarkably by plasma RE nitrocarburizing. The nitrocarburized layer with Fe3C phase formed in the mixed gases of N2：3H2 and flow rate of 0.5 L/min RE addition showed the lowest friction coefficient and the narrowest wear track.

关键词： 30CrMnSiA steel plasma nitrocarburizing rare earths surface morphology wear resistance

Microstructure and Wear Resistance of in situ Formed Duplex Coating Fabricated by Plasma Nitriding Ti Coated 2024 Al Alloy

在线全文

学校读者我要写书评

暂无评论

Journal of Materials Science & Technology 2014年第12期30卷 1278-1283页

作者： Fanyong Zhang Mufu Yan national key laboratory for precision hot processing of metals School of Materials Science and EngineeringHarbin Institute of Technology

In this study, plasma nitriding was carried out on pure titanium film coated 2024 Al alloy to improve its surface mechanical property. Ti film with the thickness of 3.0 mm was firstly fabricated by means of magnetron sputtering method. Then, the Ti coated specimen was subjected to plasma atmosphere comprising 40% N2e60% H2 at 430 C for 8 h. The microstructures of the nitrided specimens were characterized by X-ray diffraction and scanning electron microscopy. Microhardness tester and pin-on-disc tribometer were used to test the mechanical properties of the untreated and nitrided specimen. The results showed that the surface of the nitrided specimen was composed of three layers（i.e. the outside nitride Ti N0.3layer, the middle Al3 Ti layer and the inside Al18Ti2Mg3 layer）. The surface hardness and wear resistance of 2024 Al alloy were increased simultaneously by duplex treatment. The untreated specimen exhibited severe adhesive wear while the nitrided one behaved in middle abrasive wear.

关键词： Aluminum alloy Plasma nitriding Wear behavior Diffusion coating Wear

An innovative method for the microstructural modification of TiAl alloy solidified via direct electric current application

在线全文

学校读者我要写书评

暂无评论

Journal of Materials Science & Technology 2019年第1期35卷 23-28页

作者： Zhanxing Chen Hongsheng Ding Ruirun Chen Shiqiu Liu Jingjie Guo Hengzhi Fu national key laboratory for precision hot processing of metals School of Materials Science and Engineering Harbin Institute of Technology

Ti-48Al-2Cr-2Nb alloy solidified with the application of direct electric current has a refined and homogeneous microstructure without segregation. We observed an initial decrease followed by a subsequent increase in grain size and lamellar spacing, with the increase in current density. Similar trend can also be obtained by varying the amount of α2-phase(Ti_3Al). Using a directional solidification processing method,the columnar crystal microstructure transforms into an equiaxed crystal microstructure at a current density of 32–64 m A/mm^2. High dislocation density is also introduced with a minimum cross-sectional grain size of 460 μm at a current density of 64 mA/mm^2. The application of electric current alters the free energy of the critical nucleus and temperature via joule heating, causing a transformation from a columnar grain microstructure into an equiaxed grain microstructure. The increase in current density leads to a rise of the nucleation rate, and a resulting undercooling combined with temperature gradient contribute to growth of the primary phase, which finally results in grain coarsening at a critical current density of 96 mA/mm^*** climb and cross-slip of dislocation and the migration of grain boundary ultimately create variable lamellae spacing of TiAl alloy.

关键词： TiAl Solidification Direct electric current Microstructure

Superplastic Properties of Al_2O_3/Ni-Mn Nanocomposite Fabricated by Electrodeposition

在线全文

学校读者我要写书评

暂无评论

Journal of Materials Science & Technology 2010年第7期26卷 625-628页

作者： Guofeng Wang Kaifeng Zhang national key laboratory of precision hot processing of metals Harbin Institute of Technology Harbin 150001 China

Ni-Mn nanocomposite reinforced by Al2O3 particles was fabricated by pulse electrodeposition. The average grain size is 60 nm and the content of Mn and Al2O3 particles is 0.3 and 0.6 wt pct, respectively. The superplastic deformation behavior was further studied at the temperatures ranging from 673 to 873 K. A maximum elongation of 530% is obtained in the tension test at a temperature of 773 K and at a strain rate of 1.67×10^-3 s^-1. The curves of the flow stress vs strain rate have features similar to the trend of conventional superplastic materials. The test temperature （773 K） equals to 0.35Tin, which means the material obtains low temperature superplasticity. The microstructures of the composite were examined and grain growth was observed during deformation.

关键词： Electrodeposition Nanocomposites Low temperature superplasticity Microstructure

Effect of rare earths on mechanical properties of plasma nitrocarburized surface layer of 17-4PH steel

在线全文

学校读者我要写书评

暂无评论

Journal of Rare Earths 2009年第6期27卷 1056-1061页

作者：刘瑞良闫牧夫吴丹蕾 national key laboratory for precision hot processing of metals School of Materials Science and EngineeringHarbin Institute of Technology

The aim of this investigation is to reveal the influence of rare earths(RE) addition on mechanical properties of plasma nitrocarburized 17-4PH *** nitrocarburized layers were characterized by optical microscope,scanning electron microscope equipped with energy dispersive X-ray analyzer,X-ray diffractometer,microhardness tester and pin-on-disc *** results showed that RE atoms could diffuse into the surface layer of 17-4PH steel plasma nitrocarburized at 500 °C for 4 h and did not change the ...

关键词： 17-4PH steel plasma nitrocarburizing mechanical properties rare earths

Phase Field Simulation for Grains Evolution of 17-4PH Steel During Cyclic Heat Treatment

在线全文

学校读者我要写书评

暂无评论

Acta Metallurgica Sinica(English Letters) 2013年第2期26卷 183-187页

作者： Yuan YOU Mufu YAN Chengsong ZHANG national key laboratory for precision hot processing of metals School of Materials Science and Engineering Harbin Institute of Technology

A phase field model is developed to simulate the grain evolution of 17-4PH steel during cyclic heat treatment （CHT）. Our simulations successfully reproduce the grain morphologies of every CHT. In the process of every CHT, phase transformation recrystallization happens. The recrystallized grains appear mainly on the original grain boundaries. The average grain size of 13.2 μm obtained by 1040 ℃×1 h solution treatment for this experimental steel can be refined to 2.2 μm after five CHT＇s. Furthermore, the effects of phenomenological parameters in our model are discussed.

关键词： Phase field model Grain refinement Recrystallization 17-4PH Steel

The effect of metal/non-metal ratio on the microstructure and magnetic properties of （MnFe）x(P0.5Si0.5) microwires

在线全文

学校读者我要写书评

暂无评论

Progress in Natural Science:Materials International 2024年第5期34卷 1085-1092页

作者： Lin Luo Hongxian Shen Lunyong Zhang Zhiliang Ning Jianfei Sun Manh-Huong Phan national key laboratory for precision hot processing of metals Harbin Institute of Technology Department of Physics University of South Florida

The effects of metal/non-metal ratio（M/NM = x: 1） on the microstructure and magnetocaloric properties of promising melt-extracted Mn–Fe–P–Si microwires with short heat treatment have been investigated here. More Fe2P principal phase, which is considered favorite for magnetocaloric effect（MCE）, should achieve at low M/NM ratio and the fraction of Fe2P phase increased with the reduction of x. Meanwhile, the（Mn, Fe）3Si impurity phase is formed for x = 2.00–1.90 whereas change to （Mn, Fe）5Si3structure for x = 1.85. It's worth noting that a metal deficiency resulted in the thermal hysteresis(Thys) and the magnetic hysteresis loss（Wy） decreased by ～40 %.,The magnetic transition temperature(Ttran), peak value of isothermal magnetic entropy change(-ΔSpeakiso),refrigerant capacity（RC） and effective refrigerant capacity（RCE） first increased then decreased with the decrease of x, and reached the maximums at x = 1.90, i.e., 370 K, 26.0 J kg-1K-1, 367.4 and 339.8 J kg-1, ***, the customizable microstructure and magnetic properties of the melt-extracted（MnFe）x(P0.5Si0.5)microwires will be achievable effectively by tuning M/NM ratio x, and optimized Mn–Fe–P–Si compounds with novel thermomagnetic properties will be obtained.

关键词： Mn-Fe-P-Si Microwires Melt-extraction M/NM ratio Magnetocaloric properties