检索结果-南通市图书馆

Science China(Technological Sciences) 2006年第4期49卷 445-456页

作者： Frank Dammel Peter Stephan Chair of technical thermodynamics Darmstadt University of Technology Germany

An experimental investigation was conducted on the laminar flow frictional characteristics of suspensions with microencapsulated phase change material (MEPCM) in water flowing through rectangular copper minichannels. The MEPCM was provided at an average particle size of 4.97 μm, and was mixed with distilled water to form suspen- sions with various mass concentrations ranging from 0 to 20%. The experiment was per- formed to explore the effect of MEPCM mass concentration on friction factor and pressure drop in the minichannels. The Reynolds number ranged from 200 to 2000 to provide laminar and transitional flows. It was found that the experimental data for the suspensions with 0 and 5% concentration agree well with the existing theoretical data for an incom- pressible, fully developed, laminar Newtonian flow. For the suspensions with mass con- centrations higher than 10%, there is an obvious increase in friction factor and pressure drop in comparison with laminar Newtonian flow.

关键词： microencapsulated phase change material suspension, friction factor, rectangular minichannel.

Comprehensive Assessment of STGSA Generated Skeletal Mechanism for the Application in Flame-Wall Interaction and Flame-Flow Interaction

在线全文

学校读者我要写书评

暂无评论

Journal of Thermal Science 2024年第5期33卷 1946-1960页

作者： YU Chunkan YANG Bin Institute of technical thermodynamics Karlsruhe Institute of TechnologyKarlsruhe 76131Germany Center for Combustion Energy Tsinghua UniversityBeijing 100084China

In this study,we conduct a thorough evaluation of the STGSA-generated skeletal mechanism for C_(2)H_4/*** STGSA-reduced mechanisms are taken into account,incorporating basic combustion models such as the homogeneous reactor model,one-dimensional flat premixed flame,and non-premixed counterflow ***,these models are applied to more complex combustion systems,considering factors like flame-flow interaction and flame-wall *** considerations take into account additional physical parameters and processes such as mixing frequency and *** results indicate that the skeletal mechanism adeptly captures the behavior of these complex combustion ***,it is suggested to incorporate strain rate considerations in generating the skeletal mechanism,especially when the combustion system operates under high turbulent intensity.

关键词： Species-Targeted Global Sensitivity Analysis(STGSA) mechanism reduction Partially Stirred Reactor(PaSR) spark ignition Head-on Quenching(HoQ)

Drosophila models used to simulate human ATP1A1 gene mutations that cause Charcot-Marie-Tooth type 2 disease and refractory seizures

在线全文

学校读者我要写书评

暂无评论

Neural Regeneration Research 2025年第1期20卷 265-276页

作者： Yao Yuan Lingqi Yu Xudong Zhuang Dongjing Wen Jin He Jingmei Hong Jiayu Xie Shengan Ling Xiaoyue Du Wenfeng Chen Xinrui Wang Institute of Life Sciences College of Biological Science and EngineeringFuzhou UniversityFuzhouFujian ProvinceChina NHC Key laboratory of technical Evaluation of Fertility Regulation for Non-human Primate(Fujian Maternity and Child Health Hospital) FuzhouFujian ProvinceChina Medical Research Center Fujian Maternity and Child Health HospitalCollege of Clinical Medicine for Obstetrics&Gynecology and PediatricsFujian Medical UniversityFuzhouFujian ProvinceChina Department of Neurology and Institute of Neurology of The First Affiliated Hospital Institute of Neuroscienceand Fujian Key Laboratory of Molecular NeurologyFujian Medical UniversityFuzhouFujian ProvinceChina

Certain amino acids changes in the human Na^(+)/K^(+)-ATPase pump,ATPase Na^(+)/K^(+)transporting subunit alpha 1(ATP1A1),cause Charcot-Marie-Tooth disease type 2(CMT2)disease and refractory *** develop in vivo models to study the role of Na^(+)/K^(+)-ATPase in these diseases,we modified the Drosophila gene homolog,Atpα,to mimic the human ATP1A1 gene mutations that cause *** located within the helical linker region of human ATP1A1(I592T,A597T,P600T,and D601F)were simultaneously introduced into endogenous Drosophila Atpαby CRISPR/Cas9-mediated genome editing,generating the Atpα^(TTTF)*** addition,the same strategy was used to generate the corresponding single point mutations in flies(Atpα^(I571T),Atpα^(A576T),Atpα^(P579T),and Atpα^(D580F)).Moreover,a deletion mutation(Atpα^(mut))that causes premature termination of translation was generated as a positive *** these alleles,we found two that could be maintained as homozygotes(Atpα^(I571T)and Atpα^(P579T)).Three alleles(Atpα^(A576T),Atpα^(P579)and Atpα^(D580F))can form heterozygotes with the Atpαmut *** found that the Atpαallele carrying these CMT2-associated mutations showed differential phenotypes in *** heterozygous for Atpα^(TTTF)mutations have motor performance defects,a reduced lifespan,seizures,and an abnormal neuronal *** Drosophila models will provide a new platform for studying the function and regulation of the sodium-potassium pump.

关键词： ATP1A1 Atpα bang-sensitive paralysis Charcot-Marie-Tooth disease type 2 CRISPR/Cas9 homology-directed repair Na^(+)/K^(+)-ATPase point mutation seizures sodium pump

Experimental and numerical investigation to elucidate the fluid flow through packed beds with structured particle packings

在线全文

学校读者我要写书评

暂无评论

Particuology 2024年第6期89卷 218-237页

作者： Shirin Patil Christian Gorges Joel Lòpez Bonilla Moritz Stelter Frank Beyrau Berend van Wachem laboratory of technical thermodynamics Otto-von-Guericke-Universität MagdeburgUniversitätsplatz 239106 MagdeburgGermany Chair of Mechanical Process Engineering Otto-von-Guericke-Universität MagdeburgUniversitätsplatz 239106 MagdeburgGermany

The present paper presents an experimental and numerical investigation of the dispersion of the gaseous jet flow and co-flow for the simple unit cell(SUC)and body-centred cubic(BCC)configuration of particles in packed *** experimental setup is built in such a way that suitable and simplified boundary conditions are imposed for the corresponding numerical framework,so the simulations can be done under very similar conditions as the ***,a porous plate is used for the co-flow to achieve the uniform velocity and the fully developed flow is ensured for the jet *** SUC and BCC particle beds consist of 3D-printed spheres,and the non-isotropy near the walls is mostly eliminated by placing half-spheres at the channel *** flow velocities are analysed directly at the exit of the particle bed for both beds over 36 pores for the SUC configuration and 60 pores for the BCC configuration,for particle Reynolds numbers of 200,300,and *** particle image velocimetry is experimentally arranged in such a way that the velocities over the entire region at the exit of the packed bed are obtained *** numerical method consists of a state-of-the-art immersed boundary method with adaptive mesh *** paper presents the pore jet structure and velocity field exiting from each pore for the SUC and BCC packed particle *** numerical and experimental studies show a good agreement for the SUC configuration for all flow *** the BCC configuration,some differences can be observed in the pore jet flow structure between the simulations and the experiments,but the general flow velocity distribution shows a good overall *** axial velocity is generally higher for the pores located near the centre of the packed bed than for the pores near the *** addition,the axial velocities are observed to increase near the peripheral pores of the packed *** behaviour is predominant for the BCC configuration as compared to t

关键词： Uniform particle packing Packed bed reactor Stereo particle image velocimetry Immersed boundary method

Numerical Investigation of the Flow inside the Combustion Chamber of a Plant Oil Stove

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Thermal Science 2013年第5期22卷 491-496页

作者： B. Pritz M. Werler H. Wirbser M. Gabi Institute of Fluid Machinery Karlsruhe Institute of Technology (KIT)Kaiserstr. 12 76131 Karlsruhe Germany Institute of technical thermodynamics KITKaiserstr. 12 76131 Karlsruhe Germany

Recently a low cost cooking device for developing and emerging countries was developed at KIT in cooperation with the company Bosch und Siemens Hausger^ite GmbH. After constructing an innovative basic design further development was required. Numerical investigations were conducted in order to investigate the flow inside the combustion chamber of the stove under variation of different geometrical parameters. Beyond the performance improvement a further reason of the investigations was to rate the effects of manufacturing tolerance problems. In this paper the numerical investigation of a plant oil stove by means of RANS simulation will be presented. In or- der to reduce the computational costs different model reduction steps were necessary. The simulation results of the basic configuration compare very well with experimental measurements and problematic behaviors of the ac- tual stove design could be explained by the investigation.

关键词： plant oil stove cooking device fuel evaporation combustion chamber CFD RANS

Working state map of hydrocarbon fuels for regenerative cooling

在线全文

学校读者我要写书评

暂无评论

Propulsion and Power Research 2023年第2期12卷 199-211页

作者： Chen Zhang Hui Gao Jiajun Zhao Guice Yao Dongsheng Wen School of Aeronautic Science and Engineering Beihang UniversityBeijing 100191 China bAircraft and Propulsion laboratory Ningbo Institute of TechnologyBeihang UniversityNingbo 315100 China cInstitute of thermodynamics Technical University of Munich85747Germany

Regenerative cooling by endothermic hydrocarbon fuel(EHF)is one of the most promising techniques for thermal management of supersonic or hypersonic *** to maintain the fuel working in proper states is an important issue to maximize the cooling potential of *** work proposes a novel working state map,including risking zone(RZ),thermal cracking zone(TCZ),supercritical zone(SupZ)and subcritical zone(SubZ),to differentiate possible working states of an EHF during regenerative *** n-decane flowing in a circular tube as an example,the boundaries of four zones are determined by numerical simulation covering different heat fluxes(0.2-4.0 MW·m^(-2))and mass flow rates(0.5-10.5 g·s^(-1))under two operating pressures(3.45 and 5.00 MPa).Empirical correlations for three boundary lines are obtained and the maximum cooling capacity is identified,as well as the identification of the pressure *** revelation of such new perspective of regenerative cooling is of great implication to the design and optimization of cooling system for future thermal management.

关键词： Regenerative cooling Hydrocarbon fuel State map Chemical heat sink Thermal management

Tackling global electricity shortage through human power： technical opportunities from direct or indirect utilizations of the pervasive and green human energy

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Frontiers in Energy 2012年第3期6卷 210-226页

作者： Dan DAI Jing LIU Key laboratory Of Cryogenics Technical Institute of Physics and ChemistryChinese Academy of SciencesBejing 100190China Key laboratory of Cryogenics Technical Institute of Physics and ChemistryChinese Academy of SciencesBejing 100190China Department of Biomedical Engineering School Of MedicineTsinghua UniversityBeijing 100080China

With the energy and environmental problems becoming increasingly serious, human power, as a pervasive, renewable, mobile and environment friendly energy, draws more and more attention over the world. In this paper, the most basic features of human power are presented. The currently available human power harvesting theories and devices are briefly reviewed and compared. Further, direct or indirect utilization of human power in daily life, especially transportation and home appliances, such as human-powered car, watercraft, air- craft, washing machine and television etc. are summarized. Considering that the total energy from an individual is rather limited, as previously focused by most of the former works, it is conceived in this paper that an important future for large scale use of human powers lies in the efficient conversion, collection and storage of such energy from discrete people and then use it later on as desired. With the huge amount of energy gathered, the application category of human power would be significantly expended. Starting from this point, three technical ways towards efficiently utilizing human power are sketched, which are termed as human-powered grid （HPG）, human-powered charger （HPC） and human-powered storage （HPS）, among which, HPG is capable of collecting the electric power produced by each individual at different regions and thus can supply unique and flexible power to the customers covered in the area, without relying on the conventional electricity grid. The HPC can then charge various kinds of electrical devices instantly by a human driven generator which converts human power into electricity. Finally, the HPS can store electricity in time for later use. In this way, even for the devices requiring electricity that is strong enough, the collected human power can also serve as its reliable energy source. Meanwhile, utilization of human power becomes rather convenient and timely which guarantees its practical value. It is expected that wit

关键词： human energy harvesting human-powered transportation human-powered home appliances human-powered grid (HPG) human-powered charger (HPC),human-powered storage (HPS) biofuel

Fabrication and characterization of an AlGaN/PZT detector

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Semiconductors 2010年第12期31卷 87-89页

作者：张燕孙璟兰王妮丽韩莉刘向阳李向阳孟祥建 State Key laboratory of Transducer Technology Shanghai Institute of Technical PhysicsChinese Academy of Sciences National laboratory for Infrared Physics Shanghai Institute of Technical PhysicsChinese Academy of Sciences

Design, fabrication and characterization of a novel two-color detector for ultraviolet and infrared applications are reported. The detector has a simple multilayer structure composed of n-Al0.3Ga0.7N/i-GaN/p- GaN/SiO2/LaNiO3/PZT/Pt fabricated on a sapphire substrate. Ultraviolet and infrared properties are measured. For the ultraviolet region, a flat band spectral response is achieved in the 302-363 nm band. The detector displays an unbiased responsivity of 0.064 A/W at 355 nm. The current-voltage curve shows that current at zero bias is -1.57 × 10^-12 A. This led to a detectivity of 1.81 × 10^11 cm- Hzl/2/W. In the infrared region, the detectivity of the detector is 1.58 × 10^5 cm. Hz1/2/W at 4μm.

关键词： A1GaN/PZT dual-band detector UV/IR responsivity detectivity

Numerical study of convective heat transfer in static arrangements of particles with arbitrary shapes:A monolithic hybrid lattice Boltzmann-finite difference-phase field solver

在线全文

学校读者我要写书评

暂无评论

Particuology 2024年第2期85卷 186-197页

作者： Reza Namdar Mohammadhassan Khodsiani Hesameddin Safari Tanya Neeraj Seyed Ali Hosseini Frank Beyrau Benoit Fond Dominique Thevenin Fathollah Varnik Interdisciplinary Centre for Advanced Materials Simulation(ICAMS) Ruhr-University BochumBochum44801Germany laboratory of technical thermodynamics University of Magdeburg"Otto von Guericke"Magdeburg39106Germany laboratory of Fluid Dynamics and technical Flows University of Magdeburg"Otto von Guericke"MagdeburgD-39106Germany Department of Mechanical and Process Engineering ETH ZurichZurich8092Switzerland ONERA The French Aerospace Lab Department of AerodynamicsAeroelasticity and Acoustics(DAAA)Paris-Saclay UniversityMeudon92190France

A compressible lattice Boltzmann-finite difference method is extended by the phase-field approach into a monolithic scheme to study fluid flow and heat transfer through regular arrangements of solid bodies of circular,elliptical and irregular *** advantage of using the phase-field method is demon-strated both in its simplicity of accounting for flow and thermal boundary conditions at solid surfaces with irregular shapes and in the capability of generating such complex-shaped *** an array of discs,numerical results for the overall solid-to-gas heat transfer rate are validated via experiments on flow through arrays of hot *** thus validated compressible LB-FD-PF hybrid scheme is used to study the dependence of heat transfer on flow and thermal boundary conditions(Reynolds number,temperature difference between the hot solid bodies and the inlet gas),porosity as well as on the shape of solid *** are rationalized in terms of the residence time of the gas close to the solid body and downstream variations of gas velocity and *** for further applications of the proposed methodology are also discussed.

关键词： Lattice Boltzmann method Finite difference scheme Convective heat transfer Diffuse interface Thermal compressible flow

Bifunctional bridging capping layer enables 24.5% efficiency of perovskite solar cells with polymer-based hole transport materials

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Science China Chemistry 2025年第01期 350-359页

作者： Can Zhu Yiyang Wang Lei Meng Beibei Qiu Jing Li Shucheng Qin Ke Hu Xin Jiang Wenbin Lai Minchao Liu Zhe Liu Chenxing Lu Jinyuan Zhang Yongfang Li Beijing National laboratory for Molecular Sciences CAS Key Laboratory of Organic Solids Institute of Chemistry Chinese Academy of Sciences School of Chemical Science University of Chinese Academy of Sciences Key laboratory of Solid State Optoelectronic Devices of Zhejiang Province College of Physics and Electronic Information Engineering Zhejiang Normal University Key laboratory of Photochemical Conversion and Optoelectronic Materials Technical Institute of Physics and ChemistryChinese Academy of Sciences laboratory of Advanced Optoelectronic Materials College of Chemistry Chemical Engineering and Materials ScienceSoochow University

Developing a bridge capping layer between perovskite and hole transport layer materials（HTMs） in the n-i-p perovskite solar cells（pero-SCs） is an effective approach to modify the morphology of HTMs and passivate the perovskite ***, we select the quinoxaline-based bifunctional passivation agent, quinoxalin-6-yl-methylamine hydrochloride（Qx MACl）,as the bridging layer, and a D-A copolymer PBQ12 containing the same quinoxaline unit as an HTM for the n-i-p pero-SCs. Due to the π-π stacking among the common quinoxaline units in the bridge layer and HTM, Qx MACl induces the π-π stacking of the PBQ12 film and improves the film morphology of HTMs with better conductivity. Additionally, Qx MACl can effectively passivate the perovskite surface, and PBQ12 possesses appropriate energy levels and high hole mobility. The pero-SCs based on FAPbI3with PBQ12/Qx MACl treatment showed a higher power conversion efficiency（PCE） of 24.05% and outstanding stability, maintaining 95.4% and 92.1% of its initial PCE after 750 h of storage and after over 800 h of thermal annealing at 85 °C, respectively. To further enhance the PCE of the PBQ12/Qx MACl-based devices, we developed a non-metal ion dopant for the PBQ12 HTM. Through trace doping of PBQ12 HTM by the non-metal ion dopant, the PCE of the PBQ12/Qx MACl-based devices reached 25.24%（the calibrated PCE of 24.55% by the National Institute of Metrology, China）.

关键词：