检索结果-南通市图书馆

Effect of characteristics and distribution of Mg_(17)Al_(12)precipitates on tensile and bending properties of high-Al-containing Mg alloys

引用

Journal of Magnesium and Alloys 2024年第2期12卷 779-793页

作者： Sumi Jo Gyo Myeong Lee Jong Un Lee Young Min Kim Sung Hyuk Park School of materials science and Engineering Kyungpook National UniversityDaegu 41566Republic of Korea Department of Magnesium Korea Institute of Materials ScienceChangwon 51508Republic of Korea

This study investigates the effect of characteristics and distribution of Mg_(17)Al_(12)precipitates on the uniaxial tensile and three-point bending properties of extruded Mg alloys containing high Al contents.The extruded Mg–9Al–1Zn–0.3Mn(AZ91)alloy contains lamellar-structured Mg_(17)Al_(12)discontinuous precipitates along the grain boundaries,which are formed via static precipitation during natural air cooling.The extruded Mg–11Al–1Zn–0.3Mn(AZ111)alloy contains spherical Mg_(17)Al_(12)precipitates at the grain boundaries and inside the grains,which are formed via dynamic precipitation during extrusion.Due to inhomogeneous distribution of precipitates,the AZ111 alloy consists of two different precipitate regions:precipitate-rich region with numerous precipitates and finer grains and precipitate-scarce region with a few precipitates and coarser grains.The AZ111 alloy exhibits a higher tensile strength than the AZ91 alloy because its smaller grain size and more abundant precipitates result in stronger grain-boundary hardening and precipitation hardening effects,respectively.However,the tensile elongation of the AZ111 alloy is lower than that of the AZ91 alloy because the weak cohesion between the dynamic precipitates and the matrix facilitates the crack initiation and propagation.During bending,a macrocrack initiates on the outer surface of bending specimen in both alloys.The AZ111 alloy exhibits higher bending yield strength and lower failure bending strain than the AZ91 alloy.The bending specimens of the AZ91 alloy have similar bending formability,whereas those of the AZ111 alloy exhibit considerable differences in bending formability and crack propagation behavior,depending on the distribution and number density of precipitates in the specimen.In bending specimens of the AZ111 alloy,it is found that the failure bending strain(ε_(f,bending))is inversely proportional to the area fraction of precipitates in the outer zone of bending specimen(A_(ppt)),with a relationship ofε_(f,bending)=–0.1A_(ppt)+5.86.

关键词： Mg–Al alloy Extrusion Bending Precipitation Microstructure

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Recent Advances in Patterning Strategies for Full‑Color Perovskite Light‑Emitting Diodes

引用

Nano-Micro Letters 2024年第3期16卷 99-137页

作者： Gwang Heon Lee Kiwook Kim Yunho Kim Jiwoong Yang Moon Kee Choi Graduate School of Semiconductor materials and Devices Engineering Center for Future Semiconductor Technology(FUST)Ulsan National Institute of Science and Technology(UNIST)Ulsan 44919Republic of Korea Department of Energy science and Engineering Daegu Gyeongbuk Institute of Science and Technology(DGIST)Daegu 42988Republic of Korea Energy science and Engineering Research Center Daegu Gyeongbuk Institute of Science and Technology(DGIST)Daegu 42988Republic of Korea Department of materials science and Engineering Ulsan National Institute of Science and Technology(UNIST)Ulsan 44919Republic of Korea Center for Nanoparticle Research Institute for Basic Science(IBS)Seoul 08826Republic of Korea

Metal halide perovskites have emerged as promising light-emitting materials for next-generation displays owing to their remarkable material characteristics including broad color tunability,pure color emission with remarkably narrow bandwidths,high quantum yield,and solution processability.Despite recent advances have pushed the luminance efficiency of monochromic perovskite light-emitting diodes(PeLEDs)to their theoretical limits,their current fabrication using the spincoating process poses limitations for fabrication of full-color displays.To integrate PeLEDs into full-color display panels,it is crucial to pattern red–green–blue(RGB)perovskite pixels,while mitigating issues such as cross-contamination and reductions in luminous efficiency.Herein,we present state-of-the-art patterning technologies for the development of full-color PeLEDs.First,we highlight recent advances in the development of efficient PeLEDs.Second,we discuss various patterning techniques of MPHs(i.e.,photolithography,inkjet printing,electron beam lithography and laserassisted lithography,electrohydrodynamic jet printing,thermal evaporation,and transfer printing)for fabrication of RGB pixelated displays.These patterning techniques can be classified into two distinct approaches:in situ crystallization patterning using perovskite precursors and patterning of colloidal perovskite nanocrystals.This review highlights advancements and limitations in patterning techniques for PeLEDs,paving the way for integrating PeLEDs into full-color panels.

关键词： Perovskite Light-emitting diode Full-color display High-resolution patterning Electroluminescence

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Enhancing BiVO_(4)photoanode performance by insertion of an epitaxial BiFeO_(3)ferroelectric layer

引用

Journal of Energy Chemistry 2024年第2期89卷 71-78,I0003页

作者： Haejin Jang Yejoon Kim Hojoong Choi Jiwoong Yang Yoonsung Jung Sungkyun Choi Donghyeon Lee Ho Won Jang Sanghan Lee School of materials science and Engineering Gwangju Institute of Science and TechnologyGwangju 61005Republic of Korea Department of materials science and Engineering Seoul National UniversitySeoul 08826Republic of Korea

BiVO_(4)(BVO)is a promising material as the photoanode for use in photoelectrochemical applications.However,the high charge recombination and slow charge transfer of the BVO have been obstacles to achieving satisfactory photoelectrochemical performance.To address this,various modifications have been attempted,including the use of ferroelectric materials.Ferroelectric materials can form a permanent polarization within the layer,enhancing the separation and transport of photo-excited electron-hole pairs.In this study,we propose a novel approach by depositing an epitaxial BiFeO_(3)(BFO)thin film underneath the BVO thin film(BVO/BFO)to harness the ferroelectric property of BFO.The self-polarization of the inserted BFO thin film simultaneously functions as a buffer layer to enhance charge transport and a hole-blocking layer to reduce charge recombination.As a result,the BVO/BFO photoanodes showed more than 3.5 times higher photocurrent density(0.65 mA cm^(-2))at 1.23 V_(RHE)under the illumination compared to the bare BVO photoanodes(0.18 m A cm^(-2)),which is consistent with the increase of the applied bias photon-to-current conversion efficiencies(ABPE)and the result of electrochemical impedance spectroscopy(EIS)analysis.These results can be attributed to the self-polarization exhibited by the inserted BFO thin film,which promoted the charge separation and transfer efficiency of the BVO photoanodes.

关键词： Photoelectrochemical Photoanode BiVO_(4) Ferroelectric materials BiFeO_(3)

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Towards high-performance and robust anion exchange membranes(AEMs)for water electrolysis:Super-acid-catalyzed synthesis of AEMs

引用

Journal of Energy Chemistry 2024年第6期93卷 478-510,I0012页

作者： Geun Woong Ryoo Sun Hwa Park Ki Chang Kwon Jong Hun Kang Ho Won Jang Min Sang Kwon Department of materials science and Engineering Research Institute of Advanced Materials(RIAM)Seoul National UniversitySeoul 08826Republic of Korea Interdisciplinary materials Measurement institute Korea Research Institute of Standards and Science(KRISS)Daejeon 34113Republic of Korea Department of Chemical and Biological Engineering and Institute of Chemical ProcessSeoul National UniversitySeoul 08826Republic of Korea Department of Applied Measurement science University of Science and TechnologyDaejeon 34113Republic of Korea

The increasing demand for hydrogen energy to address environmental issues and achieve carbon neutrality has elevated interest in green hydrogen production,which does not rely on fossil fuels.Among various hydrogen production technologies,anion exchange membrane water electrolyzer(AEMWE)has emerged as a next-generation technology known for its high hydrogen production efficiency and its ability to use non-metal catalysts.However,this technology faces significant challenges,particularly in terms of the membrane durability and low ionic conductivity.To address these challenges,research efforts have focused on developing membranes with a new backbone structure and anion exchange groups to enhance durability and ionic conductivity.Notably,the super-acid-catalyzed condensation(SACC)synthesis method stands out due to its user convenience,the ability to create high molecular weight(MW)polymers,and the use of oxygen-tolerant organic catalysts.Although the synthesis of anion exchange membranes(AEMs)using the SACC method began in 2015,and despite growing interest in this synthesis approach,there remains a scarcity of review papers focusing on AEMs synthesized using the SACC method.The review covers the basics of SACC synthesis,presents various polymers synthesized using this method,and summarizes the development of these polymers,particularly their building blocks including aryl,ketone,and anion exchange groups.We systematically describe the effects of changes in the molecular structure of each polymer component,conducted by various research groups,on the mechanical properties,conductivity,and operational stability of the membrane.This review will provide insights into the development of AEMs with superior performance and operational stability suitable for water electrolysis applications.

关键词： Green hydrogen production Water electrolysis Anion exchange membrane water electrolyzer(AEMWE) Anion exchange membranes(AEMs) Super-acid-catalyzed condensation(SACC)

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

A review of understanding electrocatalytic reactions in energy conversion and energy storage systems via scanning electrochemical microscopy

引用

Journal of Energy Chemistry 2024年第4期91卷 155-177页

作者： Jihye Park Jong Hwan Lim Jin-Hyuk Kang Jiheon Lim Ho Won Jang Hosun Shin Sun Hwa Park Interdisciplinary materials Measurement institute Korea Research Institute of Standards and ScienceDaejeon 34113Republic of Korea Department of Material science and Engineering Seoul National UniversitySeoul 08826Republic of Korea Department of Applied Measurement science University of Science and TechnologyDaejeon 34113Republic of Korea

To address climate change and promote environmental sustainability,electrochemical energy conversion and storage systems emerge as promising alternative to fossil fuels,catering to the escalating demand for energy.Achieving optimal energy efficiency and cost competitiveness in these systems requires the strategic design of electrocatalysts,coupled with a thorough comprehension of the underlying mechanisms and degradation behavior occurring during the electrocatalysis processes.Scanning electrochemical microscopy(SECM),an analytical technique for studying surface electrochemically,stands out as a powerful tool offering electrochemical insights.It possesses remarkable spatiotemporal resolution,enabling the visualization of the localized electrochemical activity and surface topography.This review compiles crucial research findings and recent breakthroughs in electrocatalytic processes utilizing the SECM methodology,specifically focusing on applications in electrolysis,fuel cells,and metal–oxygen batteries within the realm of energy conversion and storage systems.Commencing with an overview of each energy system,the review introduces the fundamental principles of SECM,and aiming to provide new perspectives and broadening the scope of applied research by describing the major research categories within SECM.

关键词： Scanning electrochemical microscopy Electrocatalyst Electrocatalysis Water splitting Fuel cell Metal-oxygen battery

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Chemical and mechanical properties of stainless, environment-friendly, and nonflammable Mg alloys (SEN alloys): A review

引用

Journal of Magnesium and Alloys 2024年第3期12卷 841-872页

作者： Jong Un Lee Hyun Ji Kim Sang-Cheol Jin Ye Jin Kim Young Min Kim Bong Sun You Jun Ho Bae Sung Hyuk Park Advanced Metals Division Korea Institute of Materials ScienceChangwon 51508Republic of Korea Department of materials science and Metallurgical Engineering Kyungpook National UniversityDaegu 41566Republic of Korea Missile Research institute Agency for Defense DevelopmentDaejeon 34060Republic of Korea

This review article provides overall understanding of stainless,environment-friendly,and nonflammable Mg alloys(SEN alloys)recently developed at the korea institute of materials science.SEN alloys are produced by adding small amounts of Ca and Y(each<1 wt%)into commercial Mg–Al based alloys,resulting in exceptional ignition and corrosion resistances and impressive mechanical properties.Their main advantages of SEN alloys are as follows.(1)A dense multi-oxide layer of SEN alloys comprising MgO,CaO,and Y_(2)O_(3) impedes the outward dispersion of Mg vapor and the inward penetration of O_(2) during oxidation,thereby enhancing the oxidation and ignition resistances.(2)The presence of Ca-and Y-based second-phase particles in SEN alloys can enhance their corrosion resistance because Ca-containing particles prevent the spread of corrosion,and the replacement of Al-containing particles with less noble ones containing Y(e.g.,Al–Mn–Y or Al–Y particles)retards corrosion.(3)The addition of minor amounts of Ca and Y renders excellent mechanical properties due to improved strengthening effects.These enhanced properties are attributed to more pronounced dynamic recrystallization and grain refining behaviors caused by the second-phase particles during extrusion.(4)Despite the presence of various types of second-phase particles,the fatigue properties of SEN9 alloys are similar to those of commercial AZ91 alloys.(5)Simultaneous introduction of Ca and Y suppresses the formation of Mg17Al12 discontinuous precipitates during aging,leading to the enhanced elongation of aged SEN alloys.(6)Adding mischmetal into the SEN9 alloy leads to a six-fold enhancement in extrudability.Consequently,the studies conducted on SEN alloys demonstrate their excellent ignition and corrosion resistances and mechanical properties,which broaden the industrial applications of Mg alloys by addressing their inherent weaknesses.

关键词： SEN magnesium alloy Corrosion resistance Ignition resistance Mechanical properties Extrudability.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Nanoparticle Exsolution on Perovskite Oxides:Insights into Mechanism,Characteristics and Novel Strategies

引用

Nano-Micro Letters 2024年第2期16卷 312-346页

作者： Yo Han Kim Hyeongwon Jeong Bo‑Ram Won Hyejin Jeon Chan‑ho Park Dayoung Park Yeeun Kim Somi Lee Jae‑ha Myung Department of materials science and Engineering Incheon National UniversityIncheon 22012Republic of Korea

Supported nanoparticles have attracted considerable attention as a promising catalyst for achieving unique properties in numerous applications,including fuel cells,chemical conversion,and batteries.Nanocatalysts demonstrate high activity by expanding the number of active sites,but they also intensify deactivation issues,such as agglomeration and poisoning,simultaneously.Exsolution for bottomup synthesis of supported nanoparticles has emerged as a breakthrough technique to overcome limitations associated with conventional nanomaterials.Nanoparticles are uniformly exsolved from perovskite oxide supports and socketed into the oxide support by a one-step reduction process.Their uniformity and stability,resulting from the socketed structure,play a crucial role in the development of novel nanocatalysts.Recently,tremendous research efforts have been dedicated to further controlling exsolution particles.To effectively address exsolution at a more precise level,understanding the underlying mechanism is essential.This review presents a comprehensive overview of the exsolution mechanism,with a focus on its driving force,processes,properties,and synergetic strategies,as well as new pathways for optimizing nanocatalysts in diverse applications.

关键词： Supported nanoparticle Exsolution In situ growth Mechanism Perovskite oxide Catalyst

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Modeling asymmetric fracture mechanics of Mg alloy wire in drawing process

引用

Journal of Magnesium and Alloys 2024年第5期12卷 2057-2069页

作者： Sunghoon Choi Jongwon Shin Joung Sik Suh Dongchoul Kim Department of Mechanical Engineering Sogang University Advanced Metals Division Korea Institute of Materials Science

In this study, a numerical analysis was conducted on the ductile fracture of a 2-mm diameter Mg-1Zn-0.5Mn-0.5Sr-0.1Ca alloy wire during drawing. The hexagonally close-packed crystal structure of Mg alloys causes asymmetric fracture behavior, especially in the compression region. The aim of this study is to develop a comprehensive damage model for Mg alloy wire that accurately predicts ductile fracture, with a focus on the compression region. A novel experimental method was introduced to measure the ductile fracture of Mg alloy wires under different stress states. The wire drawing process was simulated using the Generalized Incremental Stress-State dependent damage(GISSMO)Model and the Semi-Analytical Model for Polymers(SAMP) model. The damage model's prediction and the experimental results were found to be in excellent agreement, especially in determining crack initiation. Computational analysis established a safe zone diagram for die angle and reduction ratio, and experimental validation confirmed the feasibility of this approach. The proposed damage model can provide a practical and reliable analysis for optimizing the drawing process of Mg alloy wire.

关键词： Mg alloy Wire drawing Finite element method Damage model Safe zone diagram

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Surface-functionalized hole-selective monolayer for high efficiency single-junction wide-bandgap and monolithic tandem perovskite solar cells

引用

Journal of Energy Chemistry 2024年第1期88卷 317-326,I0008页

作者： Devthade Vidyasagar Yeonghun Yun Jae Yu Cho Hyemin Lee Kyung Won Kim Yong Tae Kim Sung Woong Yang Jina Jung Won Chang Choi Seonu Kim Rajendra Kumar Gunasekaran Seok Beom Kang Kwang Heo Dong Hoe Kim Jaeyeong Heo Sangwook Lee School of materials science and Engineering Kyungpook National UniversityDaegu 41566Republic of Korea Department of materials science and Engineering and Optoelectronics Convergence Research CenterChonnam National UniversityGwangju 61186Republic of Korea Department of materials science and Engineering Korea UniversitySeoul 02841Republic of Korea Department of Nanotechnology and Advanced materials Engineering Sejong UniversitySeoul 05006Republic of Korea

Carbazole moiety-based 2PACz([2-(9H-carbazol-9-yl)ethyl]phosphonic acid)self-assembled monolayers(SAMs)are excellent hole-selective contact(HSC)materials with abilities to excel the charge-transferdynamics of perovskite solar cells(PSCs).Herein,we report a facile but powerful method to functionalize the surface of 2PACz-SAM,by which reproducible,highly stable,high-efficiency wide-bandgap PSCs can be obtained.The 2PACz surface treatment with various donor number solvents improves assembly of 2PACz-SAM and leave residual surface-bound solvent molecules on 2PACz-SAM,which increases perovskite grain size,retards halide segregation,and accelerates hole extraction.The surface functionalization achieves a high power conversion efficiency(PCE)of 17.62%for a single-junction wide-bandgap(~1.77 e V)PSC.We also demonstrate a monolithic all-perovskite tandem solar cell using surfaceengineered HSC,showing high PCE of 24.66%with large open-circuit voltage of 2.008 V and high fillfactor of 81.45%.Our results suggest this simple approach can further improve the tandem device,when coupled with a high-performance narrow-bandgap sub-cell.

关键词： Perovskite solar cells 2PACz Monolithic tandem solar cells Wide bandgap

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Artificial optoelectronic synapse based on spatiotemporal irradiation to source-sharing circuitry of synaptic phototransistors

引用

InfoMat 2024年第2期6卷 131-141页

作者： Seungho Song Changsoon Choi Jongtae Ahn Je-Jun Lee Jisu Jang Byoung-Soo Yu Jung Pyo Hong Yong-Sang Ryu Yong-Hoon Kim Do Kyung Hwang Center for Opto-Electronic materials and Devices Post-Silicon Semiconductor InstituteKorea Institute of Science and Technology(KIST)SeoulRepublic of Korea School of Advanced materials science and Engineering Sungkyunkwan UniversitySuwonRepublic of Korea Center for Spintronics Post-Silicon Semiconductor InstituteKorea Institute of Science and Technology(KIST)SeoulRepublic of Korea Division of Nanoscience&Technology KIST SchoolUniversity of Science and Technology(UST)SeoulRepublic of Korea School of Biomedical Engineering Korea UniversitySeoulRepublic of Korea KU-KIST Graduate School of Converging science and Technology Korea UniversitySeoulRepublic of Korea

To overcome the intrinsic inefficiency of the von Neumann architecture,neuromorphic devices that perform analog vector–matrix multiplication have been highlighted for achieving power-and time-efficient data processing.In particular,artificial synapses,of which conductance should be programmed to represent the synaptic weights of the artificial neural network,have been intensively researched to realize neuromorphic devices.Here,inspired by excitatory and inhibitory synapses,we develop an artificial optoelectronic synapse that shows both potentiation and depression characteristics triggered only by optical inputs.The design of the artificial optoelectronic synapse,in which excitatory and inhibitory synaptic phototransistors are serially connected,enables these characteristics by spatiotemporally irradiating the phototransistor channels with optical pulses.Furthermore,a negative synaptic weight can be realized without the need for electronic components such as comparators.With such attributes,the artificial optoelectronic synapse is demonstrated to classify three digits with a high recognition rate(98.3%)and perform image preprocessing via analog vector-matrix multiplication.

关键词： amorphous oxide semiconductor analog processing artificial synapse neuromorphic optoelectronics

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：