检索结果-南通市图书馆

Simultaneously enhancing the strength and ductility of as-extruded AlN/AZ91 composites via nano-precipitation and pyramidal slip

引用

Journal of Materials Science & Technology 2024年第5期172卷 240-254页

作者： Bin Zhang Yunxia Sun Tuo Liang Yunzhen Li Tian Li Jingchao Wang Ruiru Cai Changlin Yang State key laboratory of solidification processing Northwestern Polytechnical UniversityXi’an 710072China

Age hardening is often used to optimize the mechanical properties of as-deformed Mg-based materials in industry,whereas the improvement of strength is usually accompanied by the significant loss of ductility,which hinders the application of Mg-based materials in structural components.In the present work,high strength-ductility synergy(the yield strength of 263±9 MPa,ultimate tensile strength of 398±7 MPa and elongation to fracture of 34%±1%)was realized in as-extruded AlN/AZ91 composites after optimiz-ing aging processes.Microstructural characterization shows that AlN particles induced a large number of geometrically necessary dislocations around the AlN/Mg interface during extrusion,which decreased the nucleation barrier and provided more heterogeneous nucleation sites forγ-Mg 17 Al 12 continuous precipi-tation.Meanwhile,95%of residual dislocations in as-extruded AlN/AZ91 composites were annihilated dur-ing peak-aging,suppressing the growth and coarsening of continuous precipitates.Therefore,high density of nano-sizedγ-Mg 17 Al 12 continuous precipitates was produced in as-extruded AlN/AZ91 composites af-ter peak-aging.During tension,gliding dislocations bypassed sphericalγ-Mg 17 Al 12 nano-precipitates by Orowan looping rather than cutting mechanism,which induced a strong block on dislocation motion.So high yield strength was mainly attributed to the high density of non-shearableγ-Mg 17 Al 12 nano-precipitates with spherical morphology,which was different from other Mg-Al-based systems.The results of texture evolution and slip trace analysis demonstrated that the suppression of extension twinning and less basal slip was due to the enhanced activity of pyramidalc+aslip in as-extruded AlN/AZ91 com-posites after peak-aging during the room temperature tension,meanwhile,the dislocation density of as-extruded AlN/AZ91 composites was significantly decreased during peak-aging,then higher elongation to fracture was achieved.

关键词： Magnesium matrix composites Mechanical properties Precipitation Deformation mechanisms Non-basal slip

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Tuning the surface electronic structure of noble metal aerogels to promote the electrocatalytic oxygen reduction

引用

Journal of Energy Chemistry 2024年第2期89卷 557-564,I0013页

作者： Hongxing Yuan Wei Gao Xinhao Wan Jianqi Ye Dan Wen State key laboratory of solidification processing School of Materials Science and EngineeringNorthwestern Polytechnical UniversityXi’an 710072ShaanxiChina

The sluggish kinetics of the oxygen reduction reaction(ORR)is the bottleneck for various electrochemical energy conversion devices.Regulating the electronic structure of electrocatalysts by ligands has received particular attention in deriving valid ORR electrocatalysts.Here,the surface electronic structure of Ptbased noble metal aerogels(NMAs)was modulated by various organic ligands,among which the electron-withdrawing ligand of 4-methylphenylene effectively boosted the ORR electrocatalysis.Theoretical calculations suggested the smaller energy barrier for the transformation of O^(*) to OH^(*) and downshift the d-band center of Pt due to the interaction between 4-methylphenylene and the surface metals,thus enhancing the ORR intrinsic activity.Both Pt3Ni and Pt Pd aerogels with 4-methylphenylene decoration performed significant enhancement in ORR activity and durability in different media.Remarkably,the 4-methylphenylene modified Pt Pd aerogel exhibited the higher halfwave potential of 0.952 V and the mass activity of 10.2 times of commercial Pt/C.This work explained the effect of electronic structure on ORR electrocatalytic properties and would promote functionalized NMAs as efficient ORR electrocatalysts.

关键词： Noble metal aerogels Surface electronic structure ORR Electrocatalyst Organic ligands

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Metal–organic framework wafer enabled fast response radiation detection with ultra-low dark current

引用

Nano Research 2024年第4期17卷 2988-2993页

作者： Meng Xu Jianxi Liu Wei Wu Yang Chen Donghao Ma Sixin Chen Wanqi Jie Menghua Zhu Yadong Xu State key laboratory of solidification processing MIIT Key Laboratory of Radiation Detection Materials and Devices&School of Materials Science and EngineeringNorthwestern Polytechnical UniversityXi’an 710072China

Semiconductive metal–organic frameworks(MOFs)have attracted great interest for the electronic applications.However,dark currents of present hybrid organic–inorganic materials are 1000–10,000 times higher than those of commercial inorganic detectors,leading to poor charge transportation.Here,we demonstrate a ZIF-8(Zn(mim)_(2),mim=2-methylimidazolate)wafer with ultra-low dark current of 1.27 pA·mm^(-2) under high electric fields of 322 V·mm^(-1).The isostatic pressing preparation process provides ZIF-8 wafers with good transmittance.Besides,the presence of redox-active metals and small spatial separation between components promotes the charge hopping.The ZIF-8-based semiconductor detector shows promising X-ray detection sensitivity of 70.82μC·Gy^(-1)·cm^(-2) with low doses exposures,contributing to superior X-ray imaging capability with a relatively high spatial resolution of 1.2 lp·mm^(-1).Simultaneously,good peak discrimination with the energy resolution of~43.78%is disclosed when the detector is illuminated by uncollimated 241Am@5.48 MeVα-particles.These results provide a broad prospect of MOFs for future radiation detection applications.

关键词： MOFs lead-free α-particles X-ray detection and imaging dark current fast response

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Preparation and characteristic of NASICON ceramics

引用

Rare Metals 2006年第Z1期25卷 39-42页

作者： ZHU Dongmei LUO Fa XIE Zhanglong ZHOU Wancheng State key laboratory of solidification processing Northwestern Polytechnical University Xi''an 710072 China State Key Laboratory of Solidification Processing Northwestern Polytechnical University Xi''an 710072 China State Key Laboratory of Solidification Processing Northwestern Polytechnical University Xi''an 710072 China State Key Laboratory of Solidification Processing Northwestern Polytechnical University Xi''an 710072 China

Hot-pressed sintering was employed to prepare the sodium super ionic conductor (Na1+xZr2SixP3-xO12, 1.8≤x≤2.2) ceramics and compare with the sample obtained from normal-press sintering. The phase formation, density, and conductivity of the hot-press sintered and the normal-press sintered samples were investigated in detail. Results show that the density of NASICON ceramics and the degree of crystallization can be improved by hot-press process efficiently. The density of the sample sintered by normal sintering is obviously lower than that sintered by hot press. XRD analysis indicates all the hot press sintered samples contain mainly monoclinic NASICON and no ZrO2 phase was found. The ionic conductivity of normal-press sintered sample is much lower than that of hot-press sintered sample. When the composition is close to Na3Zr2Si2PO12, the dc conductivities of the hot press sintered samples were in the order of 10-3 S·cm-1. The variation of the ac conductivity with frequency in the high frequency region agrees with the power law feature of σ(ω)∝ωn(0

关键词： NASICON normal sintering hot pressed sintering electronic conductivity

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Decline of nucleation in the heating process with a high heating rate

引用

Chinese Physics B 2014年第8期23卷 426-429页

作者：杨高林林鑫宋梦华胡桥汪志太黄卫东 State key laboratory of solidification processing Northwestern Polytechnical University

The effect of the heating rate on the nucleation of metallic glass in a rapid heating process starting from the glass transition temperature is investigated. The critical nucleus radius increases with the increase of the temperature of the undercooling liquid. If the increment rate of the critical nucleus radius, owing to the heating process, is higher than the growth rate of the nuclei, the nuclei generated at the low temperature will become the embryos at the high temperature. This means that the high heating rate can make no nucleation happen in the heating process. In consideration of the interfacial energy, the growth rate of the nuclei increases with the increase of their size and the growth rate of the critical nucleus is zero. Thus, the lower heating rate can also make the nuclei decline partially. Finally, this theory is used to analyze the nucleation process during laser remelting metallic glass.

关键词： nucleation growth rate heating rate bulk metallic glass

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of Intermediate Heat Treatment Temperature on Microstructure and Notch Sensitivity of Laser Solid Formed Inconel 718 Superalloy

引用

Journal of Wuhan University of Technology(Materials Science) 2011年第5期26卷 908-913页

作者：刘奋成黄卫东 State key laboratory of solidification processing Northwestern Polytechnical University

Inconel 718 superalloys deposited by laser solid forming （LSF） were heat treated with solution treatment,intermediate heat treatment （IHT） and two-stage aging treatment in sequence （SITA heat treatment）.The effect of IHT temperature on microstructure,tensile property and notch sensitivity of LSFed Inconel 718 superalloy at 500 ℃ were investigated.As-deposited columnar grains have transformed to equiaxed grains and the grains were refined due to the recrystallization during the SITA heat treatment.It is found that the size and amount of δ phase dispersed at grain boundaries decreased with the increasing of IHT temperature,and δ phase disappeared when the IHT temperature reached 1 020 ℃.The ultimate tensile strength （UTS） and yield strength （YS） of smooth samples increased to a maximum when the IHT temperature reached 980 ℃ and then decreased slightly to a minimum when the IHT temperature was 1 000 ℃,and followed by slight increasing again till the IHT temperature reached 1 020 ℃,resulted from the competition of precipitation strengthening effect of γ″ and γ＇ phase and the grain boundary weakening effect caused by the gradual disappearance of δ phase with increasing the IHT temperature.The notch sensitivity factor （qe） decreased but still greater than 1 as the IHT temperature increased,which is attributed to the decrease of the size and amount of δ precipitation.

关键词： notch sensitivity Inconel 718 laser solid forming intermediate heat treatment superalloy

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Finite element simulation on the deep drawing of titanium thin-walled surface part

引用

Rare Metals 2010年第1期29卷 108-113页

作者： GAO Enzhi, LI Hongwei, KOU Hongchao, CHANG Hui, LI Jinshan, and ZHOU Lian State key laboratory of solidification processing, Northwestern Polytechnical University, Xi’an 710072, China State key laboratory of solidification processing Northwestern Polytechnical University Xi’an China

The deep drawing of titanium thin-walled surface part was simulated based on a self-developed three-dimensional finite element model. After an investigation on forming rules, a virtual orthogonal experimental design was adopted to determine the significance of processing parameters, such as die radius, blank holder force, and friction coefficient, on the forming process. The distributions of thickness and equivalent plastic strain of the drawn part were evaluated. The results show that die radius has a relative major influence on the deep drawing process, followed by friction coefficient and blank holder force.

关键词： deep drawing titanium alloy finite element simulation orthogonal experiment processing parameters

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

A review of linear friction welding of Ni -based superalloys

引用

International Journal of Minerals,Metallurgy and Materials 2024年第6期31卷 1382-1391页

作者： Xiawei Yang Tingxi Meng Qiang Chu Yu Su Zhenguo Guo Rui Xu Wenlong Fan Tiejun Ma Wenya Li State key laboratory of solidification processing Shaanxi Key Laboratory of Friction Welding TechnologiesNorthwestern Polytechnical UniversityXi’an 710072China Xi’an Aerospace Engine Co.Ltd. Xi’an 710100China

Ni-based superalloys are one of the most important materials employed in high-temperature applications within the aerospace and nuclear energy industries and in gas turbines due to their excellent corrosion,radiation,fatigue resistance,and high-temperature strength.Linear friction welding(LFW)is a new joining technology with near-net-forming characteristics that can be used for the manu-facture and repair of a wide range of aerospace components.This paper reviews published works on LFW of Ni-based superalloys with the aim of understanding the characteristics of frictional heat generation and extrusion deformation,microstructures,mechanical proper-ties,flash morphology,residual stresses,creep,and fatigue of Ni-based superalloy weldments produced with LFW to enable future optim-um utilization of the LFW process.

关键词： Ni-based superalloys linear friction welding microstructures mechanical properties flash morphology

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Structure and Migration Characteristic of Heterointerfaces During the Phase Transformation from L1_2 to DO_(22) Phase

引用

Journal of Wuhan University of Technology(Materials Science) 2010年第5期25卷 814-819页

作者：张明义 State key laboratory of solidification processing Northwestern Polytechnical University

Based on the microscopic phase-field model, the structure and migration characteristic of ordered domain interfaces formed between DO22 and L12 phase are investigated, and the atomistic mechanism of phase transformation from L12 （Ni3Al） to DO22 （Ni3V） in Ni75AlxV25-x alloys are explored, using the simulated microstructure evolution pictures and the occupation probability evolution of alloy elements at the interface. The results show that five kinds of heterointerfaces are formed between DO22 and L12 phase and four of them can migrate during the phase transformation from L12 to DO22 except the interface （002）D//（001）L. The structure of interface （100）D//（200）L and interface （100）D//（200）L·^1/2[001] remain the same before and after migration, while the interface （002）D//（002）L is formed after the migration of interface （002）D//（002）L·^1/2[100] and vice versa. These two kinds of interface appear alternatively. The jump and substitute of atoms selects the optimization way to induce the migration of interface during the phase transformation, and the number of atoms needing to jump during the migration is the least among all of the possible atom jump modes.

关键词： phase transformation ordered domain interface interface migration microscopic phase-field Ni75AlxV25-x alloy

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Fabrication and Microstructure of CaTiO_3 Coating by Laser Cladding

引用

Journal of Wuhan University of Technology(Materials Science) 2011年第6期26卷 1093-1097页

作者：吕晓卫黄卫东 State key laboratory of solidification processing Northwestern Polytechnical University

In order to explore the way to improve the adhesion of the calcium phosphate bioceramic coating to Ti substrate, the CaTiO3 coating was fabricated on Ti substrate by laser cladding （LC） using powders of CaCO3 and CaHPO4, and then the composition and microstructure of the coatings were investigated. During LC, CaCO3 can hardly react with Ti, and the coating fabricated using CaCO3 powder is mainly composed of the process of CaO, the decomposition product of CaCO3. Moreover, the coating has a loosened structure and part of it has peeled off from the substrate. CaHPO4 reacts vigorously with Ti, and the coating fabricated using CaHPO4 mainly consists of CaTiO3 which is one of the reaction products between Ti and CaHPO4. Chemical bonding is formed at the interface between coating and substrate, which may enhance the adhesion of the CaTiO3 coating to Ti substrate. Furthermore, CaTiO3 dendrite and eutectic of CaTiO3 and Ca2P2O7 are found on the surface of the coating, implying that a transition can be formed between CaTiO3 and some calcium phosphate bioceramic. So CaTiO3 coating fabricated using CaHPO4 can be a potential candidate to improve the adhesion between calcium phosphate coating and Ti substrate. However, there are also pores and cracks existing in the coating, which may degrade the mechanical properties of the coating.

关键词： CaTiO3 coating CaCO3 CaHPO4 Ti substrate laser cladding

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：