检索结果-南通市图书馆

Earthquake Engineering and Engineering Vibration 2024年第1期23卷 163-178页

作者： Wu Houli Guo Endong Wang Jingyi Dai Xin Dai Chenxi Key Laboratory of Earthquake Engineering and Engineering Vibration Institute of Engineering MechanicsChina Earthquake AdministrationHarbin 150080China Key Laboratory of Earthquake disaster Mitigation Ministry of Emergency ManagementHarbin 150080China

As an important part of nonstructural components,the seismic response of indoor water supply pipes deserves much attention.This paper presents shaking table test research on water supply pipes installed in a full-scale reinforced concrete(RC)frame structure.Different material pipes and different methods for penetrating the reinforced concrete floors are combined to evaluate the difference in seismic performance.Floor response spectra and pipe acceleration amplification factors based on test data are discussed and compared with code provisions.A seismic fragility study of displacement demand is conducted based on numerical simulation.The acceleration response and displacement response of different combinations are compared.The results show that the combination of different pipe materials and different passing-through methods can cause obvious differences in the seismic response of indoor riser pipes.

关键词： water supply pipe different materials shaking table test amplification factor seismic fragility

Comparative Experimental Study on Heat Transfer Characteristics of Building Exterior Surface at High and Low Altitudes

在线全文

学校读者我要写书评

暂无评论

Journal of Thermal Science 2024年第3期33卷 1119-1131页

作者： JIA Yonghong GUO Shurui LI Jin GUO Lei CHENG Zhu ZHANG Yin YANG Hanyu LONG Enshen institute for disaster management and Reconstruction Sichuan UniversityChengdu610065China MOE Key Laboratory of Deep Earth Science and Engineering College of Architecture and EnvironmentSichuan UniversityChengdu610065China

The external surface heat transfer coefficient of building envelope is one of the important parameters necessary for building energy saving design,but the basic data in high-altitude area are scarce.Therefore,the authors propose a modified measurement method based on the heat balance of a model building,and use the same model building to measure its external surface heat transfer coefficient under outdoor conditions in Chengdu city,China at an altitude of 520 m and Daocheng city at an altitude of 3750 m respectively.The results show that the total heat transfer coefficient(h_(t))of building surface in high-altitude area is reduced by 34.48%.The influence of outdoor wind speed on the convective heat transfer coefficient(h_(c))in high-altitude area is not as significant as that in low-altitude area.The fitting relation between convection heat transfer coefficient and outdoor wind speed is also obtained.Under the same heating power,the average temperature rise of indoor and outdoor air at highaltitude is 41.9%higher than that at low altitude,and the average temperature rise of inner wall is 25.8%higher than that at low altitude.It shows that high-altitude area can create a more comfortable indoor thermal environment than low-altitude area under the same energy consumption condition.It is not appropriate to use the heat transfer characteristics of the exterior surface of buildings in low-altitude area for building energy saving design and related heating equipment selection and system terminal matching design in high-altitude area.

关键词： altitude heat transfer characteristics convective heat transfer coefficient(h_(c)) radiative heat transfer coefficient(h_(r)) external building envelope

Numerical Simulation of the Seismic Response of a Horizontal Storage Tank Based on a SPH-FEM Coupling Method

在线全文

学校读者我要写书评

暂无评论

Computer Modeling in Engineering & Sciences 2024年第5期139卷 1655-1678页

作者： Peilei Yan Endong Guo HouliWu Liangchao Zhang Key Laboratory of Earthquake Engineering and Engineering Vibration Institute of Engineering MechanicsChina Earthquake AdministrationHarbin150080China Key Laboratory of Earthquake disaster Mitigation Ministry of Emergency ManagementHarbin150080China

A coupled numerical calculation method combining smooth particle hydrodynamics(SPH)and the finite element method(FEM)was implemented to investigate the seismic response of horizontal storage tanks.Anumericalmodel of a horizontal storage tank featuring a free liquid surface under seismic action was constructed using the SPH–FEM coupling method.The stored liquid was discretized using SPH particles,while the tank and supports were discretized using the FEM.The interaction between the stored liquid and the tank was simulated by using the meshless particle contact method.Then,the numerical simulation results were compared and analyzed against seismic simulation shaking table test data to validate the method.Subsequently,a series of numerical models,considering different liquid storage volumes and seismic effects,were constructed to obtain time history data of base shear and top center displacement,which revealed the seismic performance of horizontal storage tanks.Numerical simulation results and experimental data showed good agreement,with an error rate of less than 18.85%.And this conformity signifies the rationality of the SPH-FEM coupling method.The base shear and top center displacement values obtained by the coupled SPH-FEM method were only 53.3% to 69.1% of those calculated by the equivalent mass method employed in the current code.As the stored liquid volume increased,the seismic response of the horizontal storage tank exhibited a gradual upward trend,with the seismic response increasing from 73% to 388% for every 35% increase in stored liquid volume.The maximum von Mises stress of the tank and the supports remained below the steel yield strength during the earthquake.The coupled SPH-FEM method holds certain advantages in studying the seismic problems of tanks with complex structural forms,particularly due to the representation of the flow field distribution during earthquakes by involving reservoir fluid participation.

关键词： SPH-FEM coupling method horizontal storage tank seismic response sloshing

Effect of dynamic loading orientation on fracture properties of surrounding rocks in twin tunnels

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Rock Mechanics and Geotechnical Engineering 2024年第2期16卷 393-409页

作者： Ze Deng Zheming Zhu Lei Zhou Leijun Ma Jianwei Huang Yao Zhang Key Laboratory of Deep Earth and Engineering(Ministry of Education) College of Architecture and EnvironmentSichuan UniversityChengdu610065China Failure Mechanics and Engineering disaster Prevention Key Laboratory of Sichuan Province College of Architecture and EnvironmentSichuan UniversityChengdu610065China institute for disaster management and Reconstruction Sichuan UniversityChengdu610065China

For expedited transportation,vehicular tunnels are often designed as two adjacent tunnels,which frequently experience dynamic stress waves from various orientations during blasting excavation.To analyze the impact of dynamic loading orientation on the stability of the twin-tunnel,a split Hopkinson pressure bar(SHPB)apparatus was used to conduct a dynamic test on the twin-tunnel specimens.The two tunnels were rotated around the specimen’s center to consider the effect of dynamic loading orientation.LS-DYNA software was used for numerical simulation to reveal the failure properties and stress wave propagation law of the twin-tunnel specimens.The findings indicate that,for a twin-tunnel exposed to a dynamic load from different orientations,the crack initiation position appears most often at the tunnel corner,tunnel spandrel,and tunnel floor.As the impact direction is created by a certain angle(30°,45°,60°,120°,135°,and 150°),the fractures are produced in the middle of the line between the left tunnel corner and the right tunnel spandrel.As the impact loading angle(a)is 90°,the tunnel sustains minimal damage,and only tensile fractures form in the surrounding rocks.The orientation of the impact load could change the stress distribution in the twin-tunnel,and major fractures are more likely to form in areas where the tensile stress is concentrated.

关键词： Twin-tunnel Dynamic load Split Hopkinson pressure bar(SHPB) Fracture mode Stress distribution Displacement field distribution

Projections of summer light rain frequency in typical terrain over eastern China under wind speed constraint

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Science China Earth Sciences 2024年第6期67卷 1885-1894页

作者： Xuechen DONG Daoyi GONG Cuicui SHI institute of disaster Risk Science Faculty of Geographical ScienceBeijing Normal UniversityBeijing 100875China Key Laboratory of Environmental Change and Natural disaster MOEFaculty of Geographical ScienceBeijing Normal UniversityBeijing 100875China School of National Safety and Emergency management Beijing Normal UniversityBeijing 100875China School of Systems Science Beijing Normal UniversityBeijing 100875China

The variation in near-surface wind speed is a key dynamic parameter in the orographic effect of precipitation over eastern China.In this study,we used the latest high-resolution outputs from six GCMs in CMIP6-HighResMIP to evaluate the performance of high-resolution models in simulating the orographic precipitation characteristics of typical mountainous areas in summer over eastern China.The orographic precipitation under warming scenarios was projected and constrained according to observational data.The results indicated that during the contemporary climate reference period(1979-2009),although the relationship between model-simulated near-surface wind speed and orographic light rain frequency was consistently stable,the sensitivity of the orographic light rain frequency to surface wind variability was generally underestimated,with a deviation approximately 24.1% lower than the observational values.The estimated orographic light rain frequency corrected based on the observed near-surface wind speed under a 1.5℃ warming scenario,was 36.1% lower than that of the contemporary period;this reduction was 8.6 times that without the wind speed constraint(4.2%).The MRI-AGCM3-2-S model,with a longer dataset,demonstrated relatively stable reductions in orographic light rain frequency under different warming scenarios(1.5℃,2℃,3℃,and 4℃)after the application of wind speed constraints.In all cases,the reductions exceeded those for the predictions made without the wind speed constraint.

关键词： Frequency of orographic light rain HighResMIP High-resolution projection Observational constraint Eastern China

A Sustainable Strategy for Spent Cathode Carbon Blocks Hazardous Waste Recycling Using Binary Molten Salt Thermal Treatment

在线全文

学校读者我要写书评

暂无评论

Journal of Thermal Science 2024年第3期33卷 1082-1093页

作者： LI Bin DING Yan JIAO Yuyong XU Fang WANG Xinyang ZHENG Fei ZOU Junpeng GAO Qiang HU Hongyun Faculty of Engineering China University of GeosciencesWuhan430074China institute for Natural disaster Risk Prevention and Emergency management China University of GeosciencesWuhan430074China State Key Laboratory of Coal Combustion Huazhong University of Science and TechnologyWuhan430074China

Waste-to-Energy treatment is a promising path to environment and energy management in the future.This work detailed a binary molten salt thermal treatment methodology for the detoxification of spent cathode carbon block(SCCB)waste and the recycling of carbonaceous materials.The thermal behavior of SCCB and SCCB blended with molten salts was investigated.It was found that the NaCl-Na_(2)CO_(3)binary molten salts significantly contributed to reducing pyrolysis onset temperature by 334.3 K compared to that of SCCB itself(i.e.,activation energy of pyrolysis reaction was reduced from 4.24×10^(5)to 2.30×10^(5)J/mol),thus helping to lower thermal treatment energy consumption.With the addition of binary molten salts,the residue after thermal treatment in a horizontal tube furnace experiment was separated into two layers.The bottom-layer residue was mainly composed of molten salts.The fluorine content in the form of NaF and CaF_(2)of top-layer residue was reduced significantly while the carbon content remained unchanged.Specifically,the leaching concentration of fluoride ion was decreased from 4620 mg/L to 856 mg/L.It is noted that the NaF and CaF_(2)can be removed through water-leaching and hydrothermal acid-leaching methods and thus the carbonaceous materials with a calorific value of 17.5 MJ/kg were obtained.

关键词： spent cathode carbon block hazardous solid waste detoxification binary-molten-salt thermal treatment carbon recycling pyrolysis kinetics

Automated machine learning for rainfall-induced landslide hazard mapping in Luhe County of Guangdong Province,China

在线全文

学校读者我要写书评

暂无评论

China Geology 2024年第2期7卷 315-329页

作者： Tao Li Chen-chen Xie Chong Xu Wen-wen Qi Yuan-dong Huang Lei Li National institute of Natural Hazards Ministry of Emergency Management of ChinaBeijing 100085China Key Laboratory of Compound and Chained Natural Hazards Dynamics Ministry of Emergency Management of ChinaBeijing 100085China institute of disaster Prevention Sanhe 065201China School of Emergency management Science and Engineering University of Chinese Academy of SciencesBeijing 100049China

Landslide hazard mapping is essential for regional landslide hazard management.The main objective of this study is to construct a rainfall-induced landslide hazard map of Luhe County,China based on an automated machine learning framework(AutoGluon).A total of 2241 landslides were identified from satellite images before and after the rainfall event,and 10 impact factors including elevation,slope,aspect,normalized difference vegetation index(NDVI),topographic wetness index(TWI),lithology,land cover,distance to roads,distance to rivers,and rainfall were selected as indicators.The WeightedEnsemble model,which is an ensemble of 13 basic machine learning models weighted together,was used to output the landslide hazard assessment results.The results indicate that landslides mainly occurred in the central part of the study area,especially in Hetian and Shanghu.Totally 102.44 s were spent to train all the models,and the ensemble model WeightedEnsemble has an Area Under the Curve(AUC)value of92.36%in the test set.In addition,14.95%of the study area was determined to be at very high hazard,with a landslide density of 12.02 per square kilometer.This study serves as a significant reference for the prevention and mitigation of geological hazards and land use planning in Luhe County.

关键词： Landslide hazard Heavy rainfall Harzard mapping Hazard assessment Automated machine learning Shallow landslide Visual interpretation Luhe County Geological hazards survey engineering

Factors contributing to the oxygen concentration over the Qinghai-Tibetan Plateau and its contribution rate calculation

在线全文

学校读者我要写书评

暂无评论

Science China Earth Sciences 2024年第2期67卷 497-509页

作者： Peijun SHI Ying ZHANG Yanqiang CHEN Wenquan ZHU Xiaokang HU Heyi YANG Lu JIANG Yonggui MA Haiping TANG State Key Laboratory of Earth Surface Processes and Resource Ecology Beijing Normal UniversityBeijing100875China Key Laboratory of Environmental Change and Natural disaster Ministry of EducationBeijing Normal UniversityBeijing100875China The institute for disaster management and Reconstruction Sichuan UniversityChengdu610065China Academy of Plateau Science and Sustainability People’s Government of Qinghai Province&Beijing Normal UniversityXining810016China

A decline in atmospheric oxygen concentration is projected in the 21st century given the background of global warming.The Qinghai-Tibetan Plateau is located at a high altitude,and thus,it faces a hypoxia challenge;however,knowledge of the factors contributing to its atmospheric oxygen concentration is still lacking.Here,we conducted joint observations of ecosystem oxygen production and carbon sinks and near-surface atmospheric oxygen concentrations on the Qinghai-Tibetan Plateau and meteorological elements at Beijing Fangshan Station.Using seasonal differences and statistical methods,we calculated the relative contribution rates of vegetation to changes in atmospheric oxygen concentration.Our results indicate that solar radiation,atmospheric humidity,and ecosystem oxygen consumption and production have a significant impact on the atmospheric oxygen concentration,and the impact shows temporal and spatial differences.Vegetation significantly impacts the oxygen concentration,with a contribution rate of 16.7%–24.5%,which is underestimated in existing research.Our findings provide important insights into the factors that influence atmospheric oxygen concentration and highlight the contribution of vegetation.To better understand the oxygen dynamics of the Qinghai-Tibetan Plateau,we recommend further field observations of soil respiration and vegetation photosynthesis to clarify the contributions of carbon storage,carbon sinks and other factors to the near-surface atmospheric oxygen concentration.

关键词： Qinghai-Tibetan Plateau Oxygen concentration Relative contribution rate Air temperature Vegetation

Study on a conical bearing for acceleration-sensitive equipment

在线全文

学校读者我要写书评

暂无评论

Earthquake Engineering and Engineering Vibration 2024年第1期23卷 103-128页

作者： Pang Hui Xu Wen Dai Junwu Jiang Tao Key Laboratory of Earthquake Engineering and Engineering Vibration Institute of Engineering MechanicsChina Earthquake AdministrationHarbin 150080China Key Laboratory of Earthquake disaster Mitigation Ministry of Emergency ManagementHarbin 150080China School of Civil Engineering and Transportation Beihua UniversityJilin 132013China

Seismic isolation effectively reduces seismic demands on building structures by isolating the superstructure from ground vibrations during earthquakes.However,isolation strategies give less attention to acceleration-sensitive systems or equipment.Meanwhile,as the isolation layer’s displacement grows,the stiffness and frequency of traditional rolling and sliding isolation bearings increases,potentially causing self-centering and resonance concerns.As a result,a new conical pendulum bearing has been selected for acceleration-sensitive equipment to increase self-centering capacity,and additional viscous dampers are incorporated to enhance system damping.Moreover,the theoretical formula for conical pendulum bearings is supplied to analyze the device’s dynamic parameters,and shake table experiments are used to determine the proposed device’s isolation efficiency under various conditions.According to the test results,the newly proposed devices have remarkable isolation performance in terms of minimizing both acceleration and displacement responses.Finally,a numerical model of the isolation system is provided for further research,and the accuracy is demonstrated by the aforementioned experiments.

关键词： seismic isolation acceleration-sensitive equipment the conical pendulum bearing shake table tests isolation performance,numerical model

Spatial correlations in ground motion intensity measuring from the 2023 Türkiye earthquake

在线全文

学校读者我要写书评

暂无评论

Earthquake Research Advances 2024年第1期4卷 14-22页

作者： Guoliang Shao Ruizhi Wen Hongwei Wang Yeifei Ren Baofeng Zhou Key Laboratory of Earthquake Engineering and Engineering Vibration Institute of Engineering MechanicsChina Earthquake AdministrationHarbin150080 China Key Laboratory of Earthquake disaster Mitigation Ministry of Emergency ManagementHarbin150080 China

When evaluating an area's seismic risk or resilience,it is necessary to use the spatial correlation to analyze the ground motion parameters of multiple sites together in an earthquake.These two large earthquakes in Türkiye provided the possibility for spatial correlation analysis of ground motion intensity measurements in this area.Based on the strong motion records provided by The disaster and Emergency management Authority of Türkiye(AFAD),this study uses the local ground motion prediction equation in Türkiye to give spatial correlation analysis of Intensity Measurements.This study gives an exponential model based on a semivariogram and compares it with the correlation model obtained from previous studies.

关键词： Spatial correlation Semi-variance Türkiye GMPE