检索结果-南通市图书馆

In situ polymerization of poly(3,4-ethylenedioxythiophene)protective layer towards stable zinc anode

Nano Research 2025年第1期18卷 382-394页

作者： Debin Luo Peng Zhou Xiaowei Lv Panpan Sun Xiaohua Sun Hewei Zhao College of Materials and Chemical Engineering Key Laboratory of Inorganic Nonmetallic Crystalline and Energy Conversion MaterialsChina Three Gorges UniversityYichang 443002China Hubei Three Gorges laboratory Yichang 443007China School of Chemistry Beihang UniversityBeijing 100191China

Aqueous zinc-ion devices are considered promising candidates for energy storage due to their high safety,low cost and relatively high energy ***,the dendrite growth,hydrogen evolution reaction(HER)and corrosion of the zinc anode significantly limit the development of Zn-ion ***,an inexpensive poly(3,4-ethylenedioxythiophene)(PEDOT)protective layer was constructed in situ on the Zn surface using electropolymerization to suppress dendrite growth and side reactions,thereby enhancing the reversibility of *** and theoretical calculations revealed that this hydrophilic protective layer promotes the desolvation process of hydrated Zn^(2+)and facilitates the transport of zinc ions,thus improving the thermodynamic and kinetic properties of Zn^(2+)deposition and inhibiting interfacial side ***,the optimized PEDOT@Zn symmetric battery exhibited a cycling stability exceeding 1250 h at 0.5 mA·cm^(-2)and 0.25 mAh·cm^(-2),with a significantly reduced overpotential(from 91.8 to 35 mV).With the assistance of the PEDOT protective layer,the PEDOT@Zn//Cu battery maintained approximately 99.5%Coulombic efficiency after 450 ***-situ scanning electron microscopy(SEM)and in situ optical microscopy characterizations further confirmed that the PEDOT protective layer can effectively suppress the growth of zinc ***,the Zn-ion capacitors assembled by the PEDOT@Zn and activated carbon also demonstrated outstanding cycling stability.

关键词： zinc-ion devices zinc anode poly(3 4-ethylenedioxythiophene)(PEDOT) dendrite desolvation process

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Construction of 3D porous Cu_(1.81)S/nitrogen-doped carbon frameworks for ultrafast and long-cycle life sodium-ion storage

引用

International Journal of Minerals,Metallurgy and Materials 2025年第1期32卷 191-200页

作者： Chen Chen Hongyu Xue Qilin Hu Mengfan Wang Pan Shang Ziyan Liu Tao Peng Deyang Zhang Yongsong Luo Key laboratory of Microelectronics and energy of Henan Province Henan Joint International Research Laboratory of New Energy Storage TechnologyCollege of Physics and Electronic EngineeringXinyang Normal UniversityXinyang 464000China School of Physics and Electronic Engineering Nanyang Normal UniversityNanyang 473061China

Transition metal sulfides have great potential as anode mterials for sodium-ion batteries(SIBs)due to their high theoretical specific ***,the inferior intrinsic conductivity and large volume variation during sodiation-desodiation processes seriously affect its high-rate and long-cyde performance,unbeneficial for the application as fast-charging and long-cycling SIBs ***,the three-dimensional porous Cu_(1.81)S/nitrogen-doped carbon frameworks(Cu_(1.81)S/NC)are synthesized by the simple and facile sol-gel and annealing processes,which can accommodate the volumetric expansion of Cu_(1.81)S nanoparticles and accelerate the transmission of ions and electrons during Na^(+)insertion/extraction processes,exhibiting the excellent rate capability(250.6 mA·g^(-1)at 20.0 A·g^(-1))and outstanding cycling stability(70% capacity retention for 6000 cycles at 10.0 A·g^(-1))for ***,the Na-ion full cells coupled with Na_(3)V_(2)(PO_(4))_(3)/C cathode also demonstrate the satisfactory reversible specific capacity of 330.5 mAh·g^(-1)at 5.0 A·g^(-1)and long-cycle performance with the 86.9% capacity retention at 2.0 A·g^(-1)after 750 *** work proposes a promising way for the conversionbased metal sulfides for the applications as fast-charging sodium-ion battery anode.

关键词： copper sulfide nanoparticles porous carbon framework fast charging long-cycle performance sodium-ion full batteries

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Alternative Strategy for Development of Dielectric Calcium Copper Titanate‑Based Electrolytes for Low‑Temperature Solid Oxide Fuel Cells

引用

Nano-Micro Letters 2025年第1期17卷 310-332页

作者： Sajid Rauf Muhammad Bilal Hanif Zuhra Tayyab Matej Veis MAKYousaf Shah Naveed Mushtaq Dmitry Medvedev Yibin Tian Chen Xia Martin Motola Bin Zhu College of Mechatronics and Control Engineering Shenzhen UniversityShenzhen 518060People’s Republic of China Department of Inorganic Chemistry Faculty of Natural SciencesComenius University BratislavaIlkovicova684215 BratislavaSlovakia energy Storage Joint Research Center School of Energy and EnvironmentSoutheast UniversityNanjing 210096People’s Republic of China Hydrogen energy laboratory Ural Federal University620002 EkaterinburgRussia laboratory of Electrochemical Devices Based on Solid Oxide Proton Electrolytes Institute of High Temperature Electrochemistry620066 EkaterinburgRussia School of Microelectronics Hubei UniversityWuhan 430062People’s Republic of China

The development of low-temperature solid oxide fuel cells(LT-SOFCs)is of significant importance for realizing the widespread application of *** has stimulated a substantial materials research effort in developing high oxide-ion conductivity in the electrolyte layer of *** this context,for the first time,a dielectric material,CaCu_(3)Ti_(4)O_(12)(CCTO)is designed for LT-SOFCs electrolyte application in this *** individual CCTO and its heterostructure materials with a p-type Ni_(0.8)Co_(0.15)Al_(0.05)LiO_(2−δ)(NCAL)semiconductor are evaluated as alternative electrolytes in LT-SOFC at 450–550℃.The single cell with the individual CCTO electrolyte exhibits a power output of approximately 263 mW cm^(-2) and an open-circuit voltage(OCV)of 0.95 V at 550℃,while the cell with the CCTO–NCAL heterostructure electrolyte capably delivers an improved power output of approximately 605 mW cm^(-2) along with a higher OCV over 1.0 V,which indicates the introduction of high hole-conducting NCAL into the CCTO could enhance the cell performance rather than inducing any potential short-circuiting *** is found that these promising outcomes are due to the interplay of the dielectric material,its structure,and overall properties that led to improve electrochemical mechanism in CCTO–***,density functional theory calculations provide the detailed information about the electronic and structural properties of the CCTO and NCAL and their heterostructure CCTO–*** study thus provides a new approach for developing new advanced electrolytes for LT-SOFCs.

关键词： LT-SOFCs Dielectric CaCu_(3)Ti_(4)O_(12) Semiconductor Ni_(0.8)Co_(0.15)Al_(0.05)LiO_(2−δ) Ionic conductivity Heterostructure electrolyte

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Porous Organic Cage‑Based Quasi‑Solid‑State Electrolyte with Cavity‑Induced Anion‑Trapping Effect for Long‑Life Lithium Metal Batteries

引用

Nano-Micro Letters 2025年第2期17卷 376-386页

作者： Wei-Min Qin Zhongliang Li Wen‑Xia Su Jia‑Min Hu Hanqin Zou Zhixuan Wu Zhiqin Ruan Yue‑Peng Cai Kang Li Qifeng Zheng School of Chemistry South China Normal UniversityGuangzhou 510006People’s Republic of China Key laboratory of Functional Metal‑Organic Compounds of Hunan Province College of Chemistry and Material ScienceHengyang Normal UniversityHengyang 421008People’s Republic of China Guangzhou Key laboratory of energy Conversion and energy Storage Materials Guangzhou 510006People’s Republic of China

Porous organic cages(POCs)with permanent porosity and excellent host–guest property hold great potentials in regulating ion transport behavior,yet their feasibility as solid-state electrolytes has never been testified in a practical ***,we design and fabricate a quasi-solid-state electrolyte(QSSE)based on a POC to enable the stable operation of Li-metal batteries(LMBs).Benefiting from the ordered channels and cavity-induced anion-trapping effect of POC,the resulting POC-based QSSE exhibits a high Li+transference number of 0.67 and a high ionic conductivity of 1.25×10^(−4) S cm^(−1) with a low activation energy of 0.17 *** allow for homogeneous Li deposition and highly reversible Li plating/stripping for over 2000 *** a proof of concept,the LMB assembled with POC-based QSSE demonstrates extremely stable cycling performance with 85%capacity retention after 1000 ***,our work demonstrates the practical applicability of POC as SSEs for LMBs and could be extended to other energy-storage systems,such as Na and K batteries.

关键词： Porous organic cage Cavity-induced anion-trapping Quasi-solid-state electrolyte Homogeneous Li+flux Lithium metal battery

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Photo‑Energized MoS_(2)/CNT Cathode for High‑Performance Li–CO_(2)Batteries in a Wide‑Temperature Range

引用

Nano-Micro Letters 2025年第1期17卷 160-175页

作者： Tingsong Hu Wenyi Lian Kang Hu Qiuju Li Xueliang Cui Tengyu Yao Laifa Shen Jiangsu Key laboratory of Materials and Technologies for energy Storage College of Materials Science and TechnologyNanjing University of Aeronautics and AstronauticsNanjing 210016People’s Republic of China

Li–CO_(2) batteries are considered promising energy storage systems in extreme environments such as Mars;however,severe performance degradation will occur at a subzero temperature owning to the sluggish reaction ***,a photo-energized strategy adopting sustainable solar energy in wide working temperature range Li–CO_(2) battery was achieved with a binder-free MoS_(2)/carbon nanotube(CNT)photo-electrode as *** unique layered structure and excellent photoelectric properties of MoS_(2) facilitate the abundant generation and rapid transfer of photo-excited carriers,which accelerate the CO_(2) reduction and Li_(2)CO_(3) decomposition upon *** illuminated battery at room temperature exhibited high discharge voltage of 2.95 V and mitigated charge voltage of 3.27 V,attaining superior energy efficiency of 90.2%and excellent cycling stability of over 120 *** at an extremely low temperature of−30℃,the battery with same electrolyte can still deliver a small polarization of 0.45 V by the photoelectric and photothermal synergistic mechanism of MoS_(2)/CNT *** work demonstrates the promising potential of the photo-energized wide working temperature range Li–CO_(2) battery in addressing the obstacle of charge overpotential and energy efficiency.

关键词： Li-CO_(2)batteries Photo-energized Wide operation-temperature Kinetics MoS_(2)

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

State Key laboratory of Power Grid Safety and energy Conservation,China Electric Power Research Institute,Beijing,China

引用

CSEE Journal of Power and energy Systems 2022年第3期8卷 710-720页

作者： Lin Yu Huadong Sun Shiyun Xu Bing Zhao Jian Zhang State Key laboratory of Power Grid Safety and energy Conservation China Electric Power Research InstituteBeijing100192China

The power system is experiencing a higher penetration of renewable energy generations(REGs).The short circuit ratio(SCR)and the grid impedance ratio(GIR)are two indices to quantify the system strength of the power system with *** this paper,the critical short circuit ratio(CSCR)is defined as the corresponding SCR when the system voltage is in the critical stable *** static voltage stability analysis,the mathematical expression of the CSCR considering the impact of GIR is *** maximum value of CSCR is adopted as the critical value to distinguish the weak power *** on the static equivalent circuit analysis,it is proved that the CSCR is still effective to evaluate critical system strength considering the interactive impact among ***,we find that the GIR can be neglected and the SCR can be used individually to evaluate the system strength when SCR>2 or GIR>*** correctness and rationality of the CSCR and its critical value are validated on ADPSS.

关键词： Critical short circuit ratio critical value grid impedance ratio maximum power transfer theorem static equivalent circuit analysis

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Efficient and Stable Perovskite Solar Cells and Modules Enabled by Tailoring Additive Distribution According to the Film Growth Dynamics

引用

Nano-Micro Letters 2025年第2期17卷 387-400页

作者： Mengen Ma Cuiling Zhang Yujiao Ma Weile Li Yao Wang Shaohang Wu Chong Liu Yaohua Mai Institute of New energy Technology College of Physics&Optoelectronic EngineeringJinan UniversityGuangzhou 510632People’s Republic of China Key laboratory of New Semiconductors and Devices of Guangdong Higher Education Institutes Jinan UniversityGuangzhou 510632People’s Republic of China Guangdong Mellow energy Co. LimitedYuanming RoadZhuhai 519075GuangdongPeople’s Republic of China

Gas quenching and vacuum quenching process are widely applied to accelerate solvent volatilization to induce nucleation of perovskites in blade-coating *** this work,we found these two pre-crystallization processes lead to different order of crystallization dynamics within the perovskite thin film,resulting in the differences of additive *** then tailor-designed an additive molecule named 1,3-bis(4-methoxyphenyl)thiourea to obtain films with fewer defects and holes at the buried interface,and prepared perovskite solar cells with a certified efficiency of 23.75%.Furthermore,this work also demonstrates an efficiency of 20.18%for the large-area perovskite solar module(PSM)with an aperture area of 60.84 cm^(2).The PSM possesses remarkable continuous operation stability for maximum power point tracking of T_(90)>1000 h in ambient air.

关键词： Gas quenching Additive distribution Buried passivation Blade coating Crystallization dynamics

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

An Unprecedented Efficiency with Approaching 21%Enabled by Additive‑Assisted Layer‑by‑Layer Processing in Organic Solar Cells

引用

Nano-Micro Letters 2025年第2期17卷 372-375页

作者： Shuai Xu Youdi Zhang Yanna Sun Pei Cheng Zhaoyang Yao Ning Li Long Ye Lijian Zuo Ke Gao Key laboratory of Advanced Green Functional Materials College of ChemistryChangchun Normal UniversityChangchun 130032People’s Republic of China Shandong Provincial Key laboratory for Science of Material Creation and energy Conversion School of Chemistry and Chemical EngineeringShandong UniversityQingdao 266237People’s Republic of China College of Polymer Science and Engineering Sichuan UniversityChengdu 610065People’s Republic of China State Key laboratory and Institute of Elemento‑Organic Chemistry Centre of Nanoscale Science and Technology and Key Laboratory of Functional Polymer MaterialsRenewable Energy Conversion and Storage Center(RECAST)College of ChemistryNankai UniversityTianjin 300071People’s Republic of China Institute of Polymer Optoelectronic Materials and Devices State Key laboratory of Luminescent Materials and Devices South China University of TechnologyGuangzhou 510640People’s Republic of China Tianjin Key laboratory of Molecular Optoelectronic Sciences School of Materials Science and EngineeringTianjin UniversityTianjin 300350People’s Republic of China State Key laboratory of Silicon Materials MOE Key Laboratory of Macromolecular Synthesis and FunctionalizationDepartment of Polymer Science and EngineeringZhejiang UniversityHangzhou 310027People’s Republic of China

Recently published in Joule,Feng Liu and colleagues from Shanghai Jiaotong University reported a record-breaking 20.8%power conversion efficiency in organic solar cells(OSCs)with an interpenetrating fibril network active layer morphology,featuring a bulk p-in structure and proper vertical segregation achieved through additive-assisted layer-by-layer *** optimized hierarchical gradient fibrillar morphology and optical management synergistically facilitates exciton diffusion,reduces recombination losses,and enhances light capture *** approach not only offers a solution to achieving high-efficiency devices but also demonstrates the potential for commercial applications of OSCs.

关键词： Organic solar cells Additive-assisted layer-by-layer processing Three-dimensional fibril morphology Bulk p-i-n structure Optical management

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

“Zero‑Strain” NiNb_(2)O_(6) Fibers for All‑Climate Lithium Storage

引用

Nano-Micro Letters 2025年第1期17卷 348-360页

作者： Yan Zhao Qiang Yuan Liting Yang Guisheng Liang Yifeng Cheng Limin Wu Chunfu Lin Renchao Che College of Physics Donghua UniversityShanghai 201620People’s Republic of China School of Materials Science and Engineering Institute of Materials for Energy and EnvironmentQingdao UniversityQingdao 266071People’s Republic of China laboratory of Advanced Materials Shanghai Key Laboratory of Molecular Catalysis and Innovative MaterialsAcademy for Engineering&TechnologyFudan UniversityShanghai 200438People’s Republic of China Zhejiang laboratory Hangzhou 311100People’s Republic of China Inner Mongolia University Hohhot 010021People’s Republic of China

Niobates are promising all-climate Li^(+)-storage anode material due to their fast charge transport,large specific capacities,and resistance to electrolyte ***,their moderate unit-cellvolume expansion(generally 5%–10%)during Li^(+)storage causes unsatisfactory long-term ***,“zero-strain”NiNb_(2)O_(6) fibers are explored as a new anode material with comprehensively good electrochemical *** Li^(+)storage,the expansion of electrochemical inactive NiO_(6) octahedra almost fully offsets the shrinkage of active NbO_(6) octahedra through reversible O *** superior volume-accommodation capability of the NiO_(6) layers guarantees the“zero-strain”behavior of NiNb_(2)O_(6) in a broad temperature range(0.53%//0.51%//0.74%at 25//−10//60℃),leading to the excellent cyclability of the NiNb_(2)O_(6) fibers(92.8%//99.2%//91.1%capacity retention after 1000//2000//1000 cycles at 10C and 25//−10//60℃).This NiNb_(2)O_(6) material further exhibits a large reversible capacity(300//184//318 mAh g−1 at 0.1C and 25//−10//60℃)and outstanding rate performance(10 to 0.5C capacity percentage of 64.3%//50.0%//65.4%at 25//−10//60℃).Therefore,the NiNb_(2)O_(6) fibers are especially suitable for large-capacity,fast-charging,long-life,and all-climate lithium-ion batteries.

关键词： NiNb_(2)O_(6)porous fiber “Zero-strain”mechanism Electrochemical property Harsh-temperature operation Operando characterization

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Intermolecular reductive coupling of aliphatic ketones with alkynes and alkenes by BCN photocatalysts

引用

Science China Chemistry 2025年第01期 181-185页

作者： Yanping Xia Luyang Sun Jiajia Cheng Sibo Wang Meifang Zheng Xinchen Wang State Key laboratory of Photocatalysis on energy and Environment College of Chemistry Fuzhou University

A photocatalytic process was developed for intermolecular reductive coupling of aliphatic ketones with alkynes/alkenes to furnish tertiary alcohols. Mechanistic studies support that boron carbonitrides(BCN) promote the single electron reduction of unactivated aliphatic ketones to generate ketyl radicals with visible light irradiation, which then react with alkynes and alkenes to afford the allylic and aliphatic alcohols, respectively. The heterogeneous photocatalytic system is compatible with diverse substrates including pharmaceutical-related molecules(43 examples) with reusability and scale-up experiments, verifying the complementary synthetic utility of this method to the homogeneous catalysts.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：