检索结果-南通市图书馆

Effects of two silicone resin coatings on performance of FeSiAl magnetic powder cores

Journal of Iron and Steel Research International 2024年第5期31卷 1279-1288页

作者： Jia-qi Liu Zheng-qu Zhu Pu Wang Yi-fan Li Jing Pang Jia-quan Zhang School of metallurgical and Ecological engineering University of Science and Technology BeijingBeijing100083China Qingdao Yunlu Advanced materials Technology Co. Ltd.Qingdao266232ShandongChina

Two silicon resins with excellent thermal stability,JH1123 and JH7102,are used as the insulated agents and binders for the gas-atomized FeSiAl powder,and corresponding magnetic powder cores(MPCs)are *** insulation capability and application prospects of the two silicon resins are evaluated by comparing the magnetic properties of the coated powder and *** scanning electron microscopy,energy dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy results show that uniform insulation layers are both formed on the powder ***1123 has stronger binding ability,and the JH1123-coated powder exhibits severe agglomeration,with d50(average particle size)approximately twice that of the JH7102-coated *** as-prepared MPCs exhibit outstanding soft magnetic ***,the permeability of FeSiAl@JH1123 is up to 74.0,which is 35.5%higher than that of FeSiAl@JH7102 because JH1123 can further improve the density of the *** for FeSiAl@JH7102,it has better direct current bias and lower core loss of 716.9 mW cm^(−3) at 20 mT and 1000 kHz due to its lower coercivity and greater anti-magnetic saturation ability.A comprehensive comparison shows that FeSiAl@JH1123 is suitable for medium and high frequency applications,while FeSiAl@JH7102 is more suitable for high frequency *** indicates that the use of JH1123 and JH7102 silicon resins for binding and insulated coating not only simplifies the preparation process of MPCs,but also enables the controlled production of MPCs for different applications.

关键词： FeSiAl Insulated coating Magnetic powder core Permeability Core loss

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Facile synthesis of composite polyferric magnesium-silicate-sulfate coagulant with enhanced performance in water and wastewater

引用

International Journal of Minerals,Metallurgy and materials 2024年第3期31卷 574-584页

作者： Xiangtao Huo Rongxia Chai Lizheng Gou Mei Zhang Min Guo School of metallurgical and Ecological engineering University of Science and Technology BeijingBeijing 100083China

The coagulation process is a widely applied technology in water and wastewater *** composite polyferric mag-nesium-silicate-sulfate(PFMS)coagulants were synthesized using Na_(2)SiO_(3)·9H_(2)O,Fe_(2)(SO_(4))_(3),and MgSO_(4) as raw materials in this *** effects of aging time,Fe:Si:Mg,and OH:M molar ratios(M represents the metal ions)on the coagulation performance of the as-pre-pared PFMS were systematically investigated to obtain optimum *** results showed that PFMS coagulant exhibited good co-agulation properties in the treatment of simulated humic acid-kaolin surface water and reactive dye *** the molar ratio was controlled at Fe:Si:Mg=2:2:1 and OH:M=0.32,the obtained PFMS presented excellent stability and a high coagulation *** removal efficiency of ultraviolet UV254 was 99.81%,and the residual turbidity of the surface water reached 0.56 NTU at a dosage of 30 mg·L^(-1).After standing the coagulant for 120 d in the laboratory,the removal efficiency of UV254 and residual turbidity of the surface wa-ter were 88.12%and 0.68 NTU,respectively,which accord with the surface water treatment *** addition,the coagulation performance in the treatment of reactive dye wastewater was greatly improved by combining the advantages of magnesium and iron *** with polyferric silicate-sulfate(PFS)and polymagnesium silicate-sulfate(PMS),the PFMS coagulant played a better decolor-ization role within the pH range of 7-13.

关键词： polyferric-magnesium-silicate-sulfate composite coagulants water and wastewater excellent stability high coagulation ef-ficiency decolorization

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Novel wood-plastic composite fabricated via modified steel slag:Preparation,mechanical and flammability properties

引用

International Journal of Minerals,Metallurgy and materials 2024年第9期31卷 2110-2120页

作者： Ling Zhao Kai Zhao Zhenwei Shen Yifan Wang Xiaojie Xia Hao Zhang Hongming Long School of metallurgical engineering Anhui University of TechnologyMa’anshan 243032China School of Civil engineering and Architecture Anhui University of TechnologyMa’anshan 243032China School of materials Science and engineering Anhui University of TechnologyMa’anshan 243032China Key Laboratory of metallurgical Emission Reduction and Resources Recycling(Anhui University of Technology) Ministry of EducationMa’anshan 243002China

A novel method was developed to enhance the utilization rate of steel slag(SS).Through treatment of SS with phosphoric acid and aminopropyl triethoxysilane(KH550),we obtained modified SS(MSS),which was used to prepare MSS/wood-plastic composites(MSS/WPCs)by replacing talcum powder(TP).The composites were fabricated through melting blending and hot *** mechanical and combustion properties,which comprise heat release,smoke release,and thermal stability,were systematically *** can improve the mechanical strength of the composites through grafting reactions between wood powder and ***,MSS/WPC#50(16wt%MSS)with an MSS-to-TP mass ratio of 1:1 exhibited optimal comprehensive *** with those of WPC#0 without MSS,the tensile,flexural,and impact strengths of MSS/WPC#50 were increased by 18.5%,12.8%,and 18.0%,***,the MSS/WPC#50 sample achieved the highest limited oxygen index of 22.5%,the highest vertical burning rating at the V-1 level,and the lowest horizontal burning rate at 44.2 mm/*** formation of a dense and stable char layer led to improved thermal stability and a considerable reduction in heat and smoke releases of MSS/WPC#***,the partial replacement of TP with MSS slightly compromised the mechanical and flame-retardant properties,possibly due to the weak grafting caused by SS powder *** findings suggest the suitability of MSS/WPCs for high-value-added applications as decorative panels indoors or outdoors.

关键词： modified steel slag wood–plastic composites preparation method mechanical property flame retardant

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Microstructure Characteristics and Elevated Temperature Mechanical Properties of a B Containedβ-solidifiedγ-TiAl Alloy

引用

Journal of Wuhan University of Technology(materials Science) 2024年第3期39卷 738-746页

作者：王秀琦 GUO Ruiqi 刘国怀 LI Tianrui YANG Yuxuan CHEN Yang XIN Meiling WANG Zhaodong State Key Laboratory of Rolling and Automation Northeastern UniversityShenyang 110819China School of materials Science and engineering Harbin Institute of Technology at ShenzhenShenzhen 518055China School of metallurgical engineering Anhui University of TechnologyMaanshan 243000China

The improved microstructure and enhanced elevated temperature mechanical properties of Ti-44Al-5Nb-(Mo,V,B)alloys were obtained by vacuum arc re-melting(VAR)and primary annealing heat treatment(HT)of 1260℃/6 h/Furnace cooling(FC).The phase transformation,microstructure evolution and tensile properties for as-cast and HTed alloys were *** indicate that three main phase transformation points are determined,T_(eut)=1164.3℃,T_(γsolv)=1268.3℃and T_(βtrans)=1382.8℃.There are coarse lamellar colonies(300μm in length)and neighbor reticular B2 andγgrain(3-5μm)in as-cast alloy,while lamellar colonies are markedly refined and multi-oriented(20-50μm)as well as the volume fraction and grain sizes of equiaxedγand B2 phases(about 15μm)significantly increase in as-HTed *** transformations involvingα+γ→α+γ+β/B2 and discontinuousγcoarsening contribute to the above ***(1-3μm)act as nucleation sites forβ_(eutectic) and produce massiveβgrains with different orientations,thus effectively refining the lamellar colonies and forming homogeneous multi-phase *** curves show both the alloys exhibit suitable performance at 800℃.As-cast alloy shows a higher ultimate tensile stress of 647 MPa,while a better total elongation of more than 41%is obtained for as-HTed *** mechanical properties improvement is mainly attributed to fine,multi-oriented lamellar colonies,coordinated deformation of homogeneous multi-phase microstructure and borides within lamellar interface preventing crack propagation.

关键词： TiAl alloy phase transformation heat treatment boride microstructure mechanical properties

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of slag composition on kinetic behavior of deep deoxidation of 5 wt.% Si high-silicon austenitic stainless steel

引用

Journal of Iron and Steel Research International 2024年第8期31卷 1873-1885页

作者： Guan-xiong Dou Han-jie Guo Jing Guo Xue-cheng Peng Qing-yun Chen School of metallurgical and Ecological engineering University of Science and Technology Beijing(USTB)Beijing 100083China Beijing Key Laboratory of Special Melting and Preparation of High-End Metal materials Beijing 100083China

Based on a thermodynamic study of 5 wt.%Si high-silicon austenitic stainless steel(SS-5Si)smelting using CaF_(2)-CaO-Al_(2)0_(3)-Mg-Si0_(2) slag to obtain a low oxygen content of less than 10×10^(-4) wt.%,a kinetic mass transfer model for deep deoxidation was established through laboratory studies,and the effects of slag components and temperature on deoxidation during the slag-steel reaction process of sS-5Si were systematically *** experimental data verified the accuracy of the model *** results showed that the final oxygen content in the steel at 1873 K was mainly controlled by the oxygen content derived from the activity of SiO_(2) regulated by the[Si]-[O]equilibrium reaction in the slag system;in particular,when the slag basicity R(R=w(CaO)/w(SiO2),where w(CaO)and w(SiO_(2))are the contents of CaO and SiO_(2) in the slag,respectively)is 3,the Al2O3 content in the slag needs to be less than 2.7%.The mass transfer rate equation for the kinetics of the deoxidation reaction revealed that the mass transfer of oxygen in the liquid metal is the rate-controlling step under different slag conditions at 1873 K,and the oxygen transfer coefficient ko.m increases with increasing the slag basicity from 4.0×10^(-6)m s^(-1)(R=1)to 4.3×10^(-5) m s^(-1)(R=3).ko.m values at R=2 and R=3 are almost the same,indicating that high slag basicity has little *** integral of the mass transfer rate equation for the deoxidation reaction of SS-5Si under different slag conditions is *** total oxygen content of the molten steel decreases with increasing basicity from an initial content of 22×10^(-4) to 3.2×10^(-4) wt.%(R=3),consistent with the change in ko.m with slag *** R=2,the slag-steel reaction takes 15 min to reach equilibrium(w[O]=5.5×10^(-4) wt.%),whereas at R=3,the slag-steel reaction takes 30 min to reach equilibrium(w[0]=3.2×10^(-4) wt.%).Considering the depth of deoxidation and reaction time of SS-5Si smelting,it is recommended the slag b

关键词： Slag-steel reaction Kinetics Rate-controlling step Deep deoxidation Transfer coefficient

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Chemical and mechanical properties of stainless, environment-friendly, and nonflammable Mg alloys (SEN alloys): A review

引用

Journal of Magnesium and Alloys 2024年第3期12卷 841-872页

作者： Jong Un Lee Hyun Ji Kim Sang-Cheol Jin Ye Jin Kim Young Min Kim Bong Sun You Jun Ho Bae Sung Hyuk Park Advanced Metals Division Korea Institute of Materials ScienceChangwon 51508Republic of Korea Department of materials Science and metallurgical engineering Kyungpook National UniversityDaegu 41566Republic of Korea Missile Research Institute Agency for Defense DevelopmentDaejeon 34060Republic of Korea

This review article provides overall understanding of stainless,environment-friendly,and nonflammable Mg alloys(SEN alloys)recently developed at the Korea Institute of materials *** alloys are produced by adding small amounts of Ca and Y(each<1 wt%)into commercial Mg–Al based alloys,resulting in exceptional ignition and corrosion resistances and impressive mechanical *** main advantages of SEN alloys are as follows.(1)A dense multi-oxide layer of SEN alloys comprising MgO,CaO,and Y_(2)O_(3) impedes the outward dispersion of Mg vapor and the inward penetration of O_(2) during oxidation,thereby enhancing the oxidation and ignition resistances.(2)The presence of Ca-and Y-based second-phase particles in SEN alloys can enhance their corrosion resistance because Ca-containing particles prevent the spread of corrosion,and the replacement of Al-containing particles with less noble ones containing Y(e.g.,Al–Mn–Y or Al–Y particles)retards corrosion.(3)The addition of minor amounts of Ca and Y renders excellent mechanical properties due to improved strengthening *** enhanced properties are attributed to more pronounced dynamic recrystallization and grain refining behaviors caused by the second-phase particles during extrusion.(4)Despite the presence of various types of second-phase particles,the fatigue properties of SEN9 alloys are similar to those of commercial AZ91 alloys.(5)Simultaneous introduction of Ca and Y suppresses the formation of Mg17Al12 discontinuous precipitates during aging,leading to the enhanced elongation of aged SEN alloys.(6)Adding mischmetal into the SEN9 alloy leads to a six-fold enhancement in ***,the studies conducted on SEN alloys demonstrate their excellent ignition and corrosion resistances and mechanical properties,which broaden the industrial applications of Mg alloys by addressing their inherent weaknesses.

关键词： SEN magnesium alloy Corrosion resistance Ignition resistance Mechanical properties Extrudability.

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Propagation form of internal cracks induced by continuous casting soft reduction and control strategy for internal quality

引用

Journal of Iron and Steel Research International 2024年第3期31卷 622-633页

作者： Pu Wang Liang Chen Qun-wei Tang Wei-tao Li Shao-xiang Li Jia-quan Zhang School of metallurgical and Ecological engineering University of Science and Technology BeijingBeijing 100083China Weifang Special Steel Group Co..Ltd. Weifang 262400ShandongChina School of materials Science and engineering Tsinghua UniversityBeijing 100084China

The propagation form of internal cracks induced by continuous casting soft reduction and the control strategy for enhancing the internal quality of 45 steel through industrial trials and a three-dimensional flow-heat transfer-solidification coupling model were *** results showed that the internal cracks induced by soft reduction exhibited a characteristic of being"coarse in the middle and fine at both ends",and displayed an elliptical arc distribution on the loose side of the strand cross *** cracks originated within the brittle temperature range and propagated inward to the liquid impenetrable temperature and outward to the zero ductility temperature or *** control strategy for enhancing the internal quality of the 45 steel strand through soft reduction is to adjust the casting speed or the reduction zone appropriately,ensuring that the central solid fraction of the reduction zone falls within the range of *** this point,a reasonable reduction amount is allocated to eliminate the center shrinkage cavities and center segregation,even if it results in minor reduction-induced cracks.

关键词： Continuous casting Soft reduction Crack propagation Internal quality Control strategy

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Synthesis of Long-Chain Oligomeric Donor and Acceptors via Direct Arylation for Organic Solar Cells

引用

Chinese Journal of Chemistry 2024年第5期42卷 523-532页

作者： Yu Wu Xin-Yu He Xu-Min Huang Ling-Jun Yang Peng Liu Na Chen Chang-Zhi Li Shi-Yong Liu Jiangxi Provincial Key Laboratory of Functional Molecular materials Chemistry College of MaterialsMetallurgical and ChemistryJiangxi University of Science and TechnologyGanzhouJiangxi341000 China Department of Polymer Science and engineering Zhejiang UniversityHangzhouZhejiang310027 China

The rapid synthesis of structurally complicated electron donors&acceptors still remains a major challenge in organic solar cells(OSC).In this work,we developed a highly efficient strategy to access long-chain oligomeric donor and acceptors for OSC applications.A series of cyclopentadithiophene(CPDT)and benzothiadiazole(BT)-basedπ-conjugated oligomers,i.e.,three oligomeric acceptors(BTDT)n-IC(n=1—3)and one long-chain oligomeric donor(BTDT)4-RD,are facilely synthesized by an atom-and step-economical,and labor-saving direct C—H arylation(DACH)reaction(i.e.,C—H/C—Br cross coupling).Note that(BTDT)4-RD involving five CPDT,four BT and two rhodamine(RD)building blocks is the longest oligomeric donor in the fullerene-free OSC devices ever *** dependence of the structure-property-performance correlation of(BTDT)n-IC(n=1—3)and(BTDT)4-RD on theπ-conjugation lengths is thoroughly investigated by opto-electrochemical measurements,bulk heterojunction(BHJ)OSC devices and ***(BTDT)1-IC:PBDB-T and(BTDT)4-RD:Y6 BHJs achieve power conversion efficiencies of 9.14%and 4.51%,*** findings demonstrate that DACH reaction is a powerful tool to tune the opto-electronic properties and device performances by regulating the lengths ofπ-conjugated oligomers with varied numbers of repeating units.

关键词： Long-chainπ-conjugated oligomer Organic solar cells Direct arylation Atom-economical synthesis Cyclopentadithiophene Benzothiadiazole C—H activation Conjugation Oligomers

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Cerium oxide inclusion nucleation mechanism based on classical nucleation theory and two-step nucleation

引用

Journal of Rare Earths 2024年第4期42卷 793-802页

作者： Yutang Li Jun Wang Linzhu Wang Chaoyi Chen Shufeng Yang Junqi Li Xiang Li School of materials and Metallurgy Guizhou UniversityGuiyang550025China State Key Laboratory of Public Big Data Guizhou UniversityGuiyang550025China School of metallurgical and Ecological engineering University of Science and Technology BeijingBeijing100083China Department of materials&Metallurgy engineering Guizhou Institute of TechnologyGuiyang550003China

It is challenging to assess the mechanism responsible for the nucleation of inclusions in metals at high *** present work therefore systematically investigates the nucleation of cerium oxide inclusions according to classical nucleation theory and a two-step nucleation *** nucleation rates and nucleation radii of these inclusions are obtained,and the results demonstrate a considerable difference between theoretical and experimental *** the basis of a two-step nucleation mechanism,(CeO_(2))_(n) and(Ce_(2)O_(3))_(n)(n=1-6)clusters were constructed and the thermodynamic properties of both these clusters and of cerium oxide nanoparticles were *** addition,the entropies and heat capacity changes of cerium oxides were determined using first principles calculations and are found to be consistent with literature *** present data indicate that the cerium oxide inclusion nucleation pathway can be summarized as[Ce]+[O]→(CeO_(2))n/(Ce_(2)O_(3))_(n)→(Ce_(2)O_(3))_(n)→(Ce_(2)O_(3))_(2)→core(Ce_(2)O_(3)crystal)-shell((Ce_(2)O_(3))_(2) cluster)nanoparticles→(Ce_(2)O_(3))bulk.

关键词： Cerium oxide inclusion Classical nucleation theory Two-step nucleation mechanism First principles Rare earths

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

In situ anchoring in carbon matrix of Bi_(2)O_(2)CO_(3) as a high-performance anode material for Li-ion batteries

引用

Rare Metals 2024年第8期43卷 3634-3646页

作者： Pu-Qiang He Jun Guo Hui Huang Zhong-Cheng Guo Faculty of Metallurgy and Energy engineering Kunming University of Science and TechnologyKunming 650093China Research Center of metallurgical Electrode materials engineering Technology Kunming 650106China Kunming Hendera Science and Technology Co. Ltd.Kunming 650106China

Bismuth-based anode materials have been regarded as promising Li-ion batteries due to their high theoretical ***,their low conductivity and associated volume expansion inhabited their *** this work,Bi_(2)O_(2)CO_(3)@C composites were successfully synthesized by in situ anchoring of flower-like Bi_(2)O_(2)CO_(3) nanosheets on a carbon-based substrate via *** unique composited structure of Bi_2O_(2)-CO_(3)@C leads to a stable specific capacity of 547 mAh·g^(-1)after 100 cycles at a current density of 0.1 A·g^(-1).Notably,it demonstrates excellent rate capability with a specific capacity of 210 mAh·g^(-1)at 5 A·g^(-1).After 550 cycles at a current density of 0.5 A·g^(-1),a high reversible capacity of nearly 400 mAh·g^(-1)was ***,in situ X-ray diffraction measurements clearly demonstrate the conversion between Bi and Li_(3)Bi during alloying/dealloying,confirming the good electrochemical reversibility of the materials for Li *** reaction kinetics of Bi_(2)O_(2)CO_(3)@C were further investigated using galvanostatic intermittent titration ***,Bi_2O_(2)-CO_(3)@C exhibited excellent long-term stability,maintaining its high reversible capacity for over 200 cycles at a current density of 0.5 A·g^(-1)in a full cell configuration using Li_(1.20)Mn_(0.54)Ni_(0.13)Co_(0.13)O_(2) as the cathode *** result further underscores its promising potential for lithium-ion *** work may provide inspiration for the design of alloy-type negative electrode materials for high-performance rechargeable batteries.

关键词： Bi_(2)O_(2)CO_(3) Composite materials Anode materials Full batteries

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：