检索结果-南通市图书馆

Numerical investigation of the photo-thermal characteristics of a direct absorption solar collector using Monte Carlo and finite volume methods

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Science China Technological Sciences 2024年第8期67卷 2436-2448页

作者： ZHU YanLong LI SuNing FAN JianHua KONG WeiQiang YUAN Yuan TAN HePing School of Energy Science and engineering Harbin Institute of Technology department of civil engineering and mechanical engineering Technical University of Denmark School of Vehicle and Energy Yanshan University

In this study, a novel model of photothermal conversion in a direct absorption solar collector based on the Monte Carlo and finite volume methods was built and validated and the temperatures of the novel and traditional solar collectors were compared. The sensitivity of the parameters to the radiative heat loss was investigated. Finally, the radiative heat transfer characteristics were discussed using the radiative exchange factor. The results of this study validated the advantages of the novel solar collector at both the surface and fluid temperatures. Under the conditions used in this study, the maximum temperature difference of the novel solar collector was 30 K, compared with 193 K for the traditional solar collector. Furthermore, the collector was divided into several units along the flow direction. The radiative exchange factor indicated that with an increase in the attenuation coefficient, the percentage of radiation intensity in the total solar radiation absorbed by the corresponding unit ***, it decreased with an increase in the incident angle and scattering albedo. These results provide a reference for addressing the low efficiency and thermal damage caused by traditional solar collectors at high temperatures.

关键词： direct absorption solar collector radiative heat transfer Monte Carlo

Prediction of bearing capacity of pile foundation using deep learning approaches

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Frontiers of Structural and civil engineering 2024年第6期18卷 870-886页

作者： Manish KUMAR Divesh Ranjan KUMAR Jitendra KHATTI Pijush SAMUI Kamaldeep Singh GROVER department of civil engineering SRM Institute of Science and Technology Tiruchirappalli CampusTrichy 621105India department of civil engineering National Institute of Technology PatnaBihar 800005India department of civil engineering Faculty of EngineeringThammasat School of EngineeringThammasat UniversityBangkok10200Thailand department of civil engineering Rajasthan Technical UniversityKota 324010India

The accurate prediction of bearing capacity is crucial in ensuring the structural integrity and safety of pile *** research compares the Deep Neural Networks(DNN),Convolutional Neural Networks(CNN),Recurrent Neural Networks(RNN),Long Short-Term Memory(LSTM),and Bidirectional LSTM(BiLSTM)algorithms utilizing a data set of 257 dynamic pile load tests for the first ***,this research illustrates the multicollinearity effect on DNN,CNN,RNN,LSTM,and BiLSTM models’performance and accuracy for the first time.A comprehensive comparative analysis is conducted,employing various statistical performance parameters,rank analysis,and error matrix to evaluate the performance of these *** performance is further validated using external validation,and visual interpretation is provided using the regression error characteristics(REC)curve and Taylor *** from the comparative analysis reveal that the DNN(Coefficient of determination(R^(2))_(training(TR))=0.97,root mean squared error(RMSE)_(TR)=0.0413;R^(2)_(testing(TS))=0.9,RMSE_(TS)=0.08)followed by BiLSTM(R^(2)_(TR)=0.91,RMSE_(TR)=0.782;R^(2)_(TS)=0.89,RMSE_(TS)=0.0862)model demonstrates the highest performance *** is noted that the BiLSTM model is better than LSTM because the BiLSTM model,which increases the amount of information for the network,is a sequence processing model made up of two LSTMs,one of which takes the input in a forward manner,and the other in a backward *** prediction of pile-bearing capacity is strongly influenced by ram weight(having a considerable multicollinearity level),and the effect of the considerable multicollinearity level has been determined for the model based on the recurrent neural network *** this study,the recurrent neural network model has the least performance and accuracy in predicting the pile-bearing capacity.

关键词： deep learning algorithms high-strain dynamic pile test bearing capacity of the pile

Effect of cooling media on bead geometry,microstructure,and mechanical properties of wire arc additive manufactured IN718 alloy

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Advances in Manufacturing 2024年第1期12卷 124-149页

作者： Parveen Kumar Satish Kumar Sharma Ratnesh Kumar Raj Singh department of mechanical engineering Thapar Institute of Engineering and TechnologyPatialaPunjab147004India

This work aims to present and explore thermal management techniques for the wire arc additive manufacturing(WAAM)of IN718 *** heat can be mitigated via air or water *** this study,the material was deposited under four different heat-input conditions with air or water *** air cooling,the layer is deposited in a normal atmospheric air environment,whereas with water cooling,the material is deposited inside a water tank by varying the water *** validate the air and water cooling thermal management techniques,IN718 single-pass and multilayer linear walls were deposited using the bidirectional gas metal arc welding based WAAM setup under four different heat input *** the deposition of single layers,the temperature profiles were recorded,and the geometric and microstructural features were *** multilayer wall structures,the mechanical properties(hardness,tensile strength,and elongation)were determined and assessed using the corresponding microstructural features explored through scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),and electron backscatter diffraction(EBSD)*** microstructure observed through SEM analysis in the building direction was found to be nonhomogenous compared with that in the deposition ***,water cooling was found to govern bead characteristics,such as wall width and *** grain size and anisotropy of the mechanical properties also decreased in the water-cooled ***,water cooling is an economical and efficient method to mitigate excessive heat accumulation in WAAM-deposited IN718.

关键词： Air cooling Water cooling IN718 Bead characteristics Microstructure Electron backscatter diffraction(EBSD)

mechanical performance of cold mix asphalt containing cup lump rubber as a sustainable bio-modifier

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Traffic and Transportation engineering(English Edition) 2024年第3期11卷 424-440页

作者： Syed Abdul Ghafar Muhammad Naqiuddin Mohd Warid Norhidayah Abdul Hassan Zulfiqar Ali Jattak Ashraf Abdalla Mohammed Radwan Faculty of civil engineering Universiti Teknologi MalaysiaSkudai 81310Malaysia department of civil engineering Balochistan University of Information TechnologyEngineering&Management SciencesQuettaPakistan department of civil engineering Balochistan University of Engineering and TechnologyKhuzdarPakistan department of civil engineering Faculty of EngineeringUniversity of TripoliTripoliLibya

The road construction industry aims to contribute to the protection of already compromised *** mix asphalt(CMA)is a measure initiated by the road industry to protect the environment and preserve *** having additional benefits,CMA has attracted little attention due to its inferior ***'s performance is enhanced using a sustainable binder bio-modifier,natural cup lump rubber(CLR)is one of *** study evaluated the tensile properties,rutting,moisture susceptibility,and adhesion properties of CLR-modified CMA(CMA-CR).The tensile property was enhanced by 26%due to CLR ***-CR had excellent rutting resistance of less than 2 mm rut depth at 10,000 load cycles,showing 70%improvement compared with conventional *** susceptibility evaluation indicated that CMA-CR had tensile strength ratio(TSR)value of 104%,satisfying the minimum 80%requirement of AASHTO *** also retained more than 96%bitumen *** moisture damage resistance was improved by 12%and 10%in terms of TSR and stripping,*** durability results revealed that the CMA-CR mixture prevented higher mass loss,representing 14%improvement compared with conventional CMA.

关键词： Cup lump rubber Cup lump modified cold mix asphalt Moisture damage Tensile property Rutting Digital imaging

Impact of Fin Arrangement on Heat Transfer and Melting Characteristics of Phase Change Material

在线全文

学校读者我要写书评

暂无评论

Journal of Thermal Science 2024年第2期33卷 435-456页

作者： Arun UNIYAL Yogesh K.PRAJAPATI department of mechanical engineering National Institute of Technology UttarakhandSrinagar(Garhwal)246174India department of mechanical engineering BIT SindriDhanbadJharkhand828123India

Present work investigates the heat transfer and melting behaviour of phase change material(PCM) in six enclosures(enclosure-1 to 6) filled with paraffin *** enclosures are equipped with distinct arrangements of the fins while keeping the fin's surface area equal in each *** analysis has been presented to recognize the suitable fin arrangements that facilitate improved heat transfer and melting rate of the *** wall of the enclosure is maintained isothermal for the temperature values 335 K,350 K and 365 *** length of the enclosure including fins is ranging between 0 and *** have been illustrated through the estimation of important performance parameters such as energy absorbing capacity,melting rate,enhancement ratio,and Nusselt *** has been found that melting time(to melt 100% of the PCM) is 60.5%less in enclosure-2(with two fins of equal length) as compared to the enclosure-1,having no *** the fin surface area equal,if the longer fin is placed below the shorter fin(enclosure-3),melting time is further decreased by 14.1% as compared to ***,among all the configurations,enclosure-6 with wire-mesh fin structure exhibits minimum melting time which is 68.4% less as compared to the *** on the findings,it may be concluded that fins are the main driving agent in the enclosure to transfer the heat from heated wall to the *** design and positioning of the fins improve the heat transfer rate followed by melting of the PCM in the entire area of the *** of the favourable vortices and natural convection current in the enclosure accelerate the melting phenomenon and help to reduce charging time.

关键词： phase change material enclosure fin melting fraction energy storage heat transfer

Gravity-driven powder flow and the influence of external vibration on flow characteristics

在线全文

学校读者我要写书评

暂无评论

Particuology 2024年第5期88卷 201-209页

作者： Muhammad Shahid Ansari Ratna Kumar Annabattula Sathyan Subbiah department of mechanical engineering Indian Institute of Technology MadrasChennai 600036India

The controlled and homogeneous flow of dry granular powders through hoppers is essential for applications,namely,packaging of food grains,fertilizers and additive manufacturing processes such as directed energy deposition for better product *** of the major issues encountered in the granular flows through hoppers is flow stagnation due to the well-known arching ***-assisted granular flow through hoppers is one of the mechanisms used for better mass flow *** this work,the influence of external mechanical vibration on the powder flow is investigated experimentally and using discrete element ***,the mass flow rate through the hopper increases with an increase in vibration amplitude and then decreases,signifying the existence of an optimal amplitude of *** DEM simulations explained the underlying mechanisms for the existence of an optimal amplitude of vibration corresponding to the maximum mass flow rate.A range of vibration amplitudes from 0 mm to 3.5 mm is used to study the flow behaviour;the maximum flow of around 33 g/s to 35 g/s is observed for 0.75 mm to 1.25 mm vibration amplitude for the hopper-particle combination studied in this *** work also reports the influence of vibration frequency,hopper,and particle dimension on the flow *** research facilitates the effective use of mechanical vibration to enhance powder flow that can further be extended to non-spherical and multi-material particles.

关键词： Discrete element method Flow rate Granular flow Path tracking Vibration intensity

Identification of time-varying system and energy-based optimization of adaptive control in seismically excited structure

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Earthquake engineering and engineering Vibration 2024年第1期23卷 227-240页

作者： Elham Aghabarari Fereidoun Amini Pedram Ghaderi department of civil engineering Iran University of Science and TechnologyTehran 16844Iran

The combination of structural health monitoring and vibration control is of great importance to provide components of smart *** synthetic algorithms have been proposed,adaptive control that is compatible with changing conditions still needs to be used,and time-varying systems are required to be simultaneously estimated with the application of adaptive *** this research,the identification of structural time-varying dynamic characteristics and optimized simple adaptive control are ***,reduced variations of physical parameters are estimated online using the multiple forgetting factor recursive least squares(MFRLS)***,the energy from the structural vibration is simultaneously specified to optimize the control force with the identified parameters to be *** is also performed based on the probability density function of the energy under the seismic excitation at any ***,the optimal control force is obtained by the simple adaptive control(SAC)algorithm and energy coefficient.A numerical example and benchmark structure are employed to investigate the efficiency of the proposed *** simulation results revealed the effectiveness of the integrated online identification and optimal adaptive control in systems.

关键词： integrated online identification time-varying systems structural energy multiple forgetting factor recursive least squares optimal simple adaptive control algorithm

Direct scaling of residual displacements for bilinear and pinching oscillators

在线全文

学校读者我要写书评

暂无评论

Earthquake engineering and engineering Vibration 2024年第1期23卷 129-149页

作者： Mohammad Saifullah Vinay K.Gupta department of civil engineering Indian Institute of Technology KanpurKanpur 208016India

The estimation of residual displacements in a structure due to an anticipated earthquake event has increasingly become an important component of performance-based earthquake engineering because controlling these displacements plays an important role in ensuring cost-feasible or cost-effective repairs in a damaged structure after the *** attempt is made in this study to obtain statistical estimates of constant-ductility residual displacement spectra for bilinear and pinching oscillators with 5%initial damping,directly in terms of easily available seismological,site,and model *** of the available models for the bilinear and pinching oscillators are useful when design spectra for a seismic hazard at a site are not *** statistical estimates of a residual displacement spectrum are proposed in terms of earthquake magnitude,epicentral distance,site geology parameter,and three model parameters for a given set of ductility demand and a hysteretic energy capacity coefficient in the case of bilinear and pinching models,as well as for a given set of pinching parameters for displacement and strength at the breakpoint in the case of pinching model *** proposed scaling model is applicable to horizontal ground motions in the western *** earthquake magnitudes less than 7 or epicentral distances greater than 20 km.

关键词： residual displacement spectrum bilinear hysteresis model pinching hysteresis model nonlinear analysis scaling model

Continuous flow pyrolysis of virgin and waste polyolefins:a comparative study,process optimization and product characterization

在线全文

学校读者我要写书评

暂无评论

Frontiers of Chemical Science and engineering 2024年第6期18卷 133-149页

作者： Ecrin Ekici Güray Yildiz Magdalena Joka Yildiz Monika Kalinowska ErolŞeker Jiawei Wang Karlsruhe Institute of technology Institute of Catalysis Research and TechnologyEggenstein-Leopoldshafen 76344Germany Izmir Institute of technology Faculty of EngineeringDepartment of Energy Systems EngineeringIzmir 35430Türkiye department of Materials engineering and Production Faculty of Mechanical EngineeringBialystok University of TechnologyBialystok 15-351Poland department of Agricultural and Food engineering and Environmental Development Institute of Civil Engineering and EnergeticsFaculty of Civil Engineering and Environmental SciencesBialystok University of Technology15-351 BialystokPoland department of Chemistry Biology and BiotechnologyInstitute of Civil Engineering and EnergeticsFaculty of Civil Engineering and Environmental SciencesBialystok University of TechnologyBialystok 15-351Poland Izmir Institute of technology Faculty of EngineeringDepartment of Chemical EngineeringIzmir 35430Türkiye Energy and Bioproducts Research Institute(EBRI) Aston UniversityBirmingham B47ETUnited Kingdom

Under optimal process conditions,pyrolysis of polyolefins can yield ca.90 wt%of liquid product,i.e.,combination of light oil fraction and heavier *** this work,the experimental findings reported in a selected group of publications concerning the non-catalytic pyrolysis of polyolefins were collected,reviewed,and compared with the ones obtained in a continuously operated bench-scale pyrolysis *** process parameters were used for the pyrolysis of waste and virgin counterparts of high-density polyethylene,low-density polyethylene,polypropylene and a defined mixture of those(i.e.,25:25:50 wt%,respectively).To mitigate temperature drops and enhance heat transfer,an increased feed intake is employed to create a hot melt plastic *** 1.5 g·min^(-1) feed intake,1.1 L·min^(-1) nitrogen flow rate,and a moderate pyrolysis temperature of 450℃,the formation of light hydrocarbons was favored,while wax formation was limited for polypropylene-rich *** of virgin plastics yielded more liquid(maximum 73.3 wt%)than that of waste plastics(maximum 66 wt%).Blending polyethylenes with polypropylene favored the production of liquids and increased the formation of gasoline-range *** products were mainly composed of C3 hydrocarbons,and no hydrogen production was detected due to moderate pyrolysis temperature.

关键词： waste plastics polyolefins chemical recycling pyrolysis alternative fuels waste-to-energy