检索结果-南通市图书馆

Effect of annealing temperature on microstructure and mechanical properties of Mg-Zn-Zr-Nd alloy with large final rolling deformation

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Central South University 2024年第6期31卷 1774-1789页

作者： ZHANG Jin-hai NIE Kai-bo ZHANG Jin-hua DENG Kun-kun LIU Zhi-long College of Materials Science and Engineering Taiyuan University of TechnologyTaiyuan 030024China State Key Laboratory of High-end Compressor and System technology Hefei 230031China

In this study,the Mg-3Zn-0.5Zr-χNd(χ=0,0.6)alloys were subjected to final rolling treatment with large deformation of 50%.The impact of annealing temperatures on the microstructure and mechanical properties was *** rolled Mg-3Zn-0.5Zr-0.6Nd alloy exhibited an ultimate tensile strength of 386 MPa,a yield strength of 361 MPa,and an elongation of 7.1%.Annealing at different temperatures resulted in reduced strength and obviously increased elongation for both *** mechanical properties for the Mg-3Zn-0.5Zr-0.6Nd alloy were achieved after annealing at 200℃,with an ultimate tensile strength of 287 MPa,a yield strength of 235 MPa,and an elongation of 26.1%.The numerous deformed microstructures,twins,and precipitated phases in the rolled alloy could impede the deformation at room temperature and increase the work hardening *** annealing,a decrease in the work hardening effect and an increase in the dynamic recovery effect were obtained due to the formation of fine equiaxed grains,and the increased volume fraction of precipitated phases,which significantly improved the elongation of the ***,the addition of Nd element could enhance the annealing recrystallization rate,reduce the Schmid factor difference between basal and prismatic slip systems,facilitate multi-system slip initiation and improve the alloy plasticity.

关键词： Mg-Zn-Zr-Nd alloy large final rolling deformation annealing temperatures microstructures mechanical properties

Advancing electrochemical drilling process via coupling of flow field and electric field in pulsating state generated by a novel tube tool

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Aeronautics 2024年第4期37卷 542-555页

作者： Liang CHENG Xiaolei CHEN Zhisen YE Yongjun ZHANG State Key Laboratory of Precision Electronic manufacturing technology and Equipment Guangdong University of TechnologyGuangzhou 510006China Guangdong Key Laboratory of Advanced manufacturing technology of Marine Energy Equipment Guangdong University of TechnologyGuangzhou 510006China Guangzhou Key Laboratory of Nontraditional Machining and Equipment Guangdong University of TechnologyGuangzhou 510006China

This paper introduces an improvement to electrochemical drilling process by coupling flow field and electric field in pulsating state. A novel tube with half-wedged shape at the end(HW-tube) is prepared, with both sidewall and wedged part of the HW-tube insulated. Only the flat part is utilized to provide electric field for electrochemical drilling. By rotating the HW-tube, both flow field and electric field in pulsating state are generated, alternating in different positions within the inter-electrode gap(IEG). The pulsating flow field enhances the mass transfer process, while pulsating electric field disperses material dissolution process and distribution of electrolytic byproducts. Both pulsating fields are coupled at the same frequency, further enhancing the electrochemical drilling process. Simulation results indicate that both flow field and electric field in pulsating state are generated. Compared to the traditional tube, the HW-tube significantly reduces the number of residual particles in IEG, and this number is further reduced by increasing the rotation speed. Experimental results reveal that the surface quality and dimensional uniformity of small hole are improved with HW-tube. With feed rate of 2.22 mm/min, a small hole with diameter of 1.52± 0.017 mm is drilled, resulting in a surface roughness of 0.331 μm.

关键词： Small holes Electrochemical drilling Tools Pulsating flow field Pulsating electric field

A short review of antibacterial Cu-bearing stainless steel:antibacterial mechanisms,corrosion resistance,and novel preparation techniques

在线全文

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第1期31卷 24-45页

作者： Shuai Liu Han-jie Guo School of Artificial Intelligence Beijing Technology and Business UniversityBeijing100048China Beijing Key Laboratory of Special Melting and Preparation of High-end Metal Materials University of Science and Technology BeijingBeijing100083China

Cu-bearing stainless steel is widely used in the fields of food,medical and household sanitary equipment because of its surface finish and corrosion ***,the growth of bacteria on stainless steel leads to the formation of biofilms,which causes ***,the antibacterial property of stainless steel is a worthy research *** of breakthroughs in the field of corrosion resistance and antimicrobial properties are still ***,due to the scarcity of publications on the antibacterial mechanisms and processing methods of antibacterial Cu-bearing stainless steel,we review the current state of relevant research and *** toxicity of Cu,corrosion resistance mechanism of stainless steel,and antibacterial mechanism and preparation method of antibacterial stainless steel are *** addition,alloying,surface modification and other methods are found to have limitations in balancing the toxicity and antibacterial properties of copper and the relationship between the antibacterial properties and corrosion resistance of Cu-bearing stainless steel.A new preparation method of antibacterial stainless steel associated with selective laser melting(SLM)is *** is becoming a powerful additive manufacturing technology that can be used to manufacture customized and complex *** research status of SLM applied in antibacterial stainless steel preparation is ***,the future research direction of Cu-bearing antibacterial stainless steel is discussed.

关键词： Cu-bearing stainless steel Antibacterial Processing Additive manufacturing Corrosion resistance

Design and optimization of fluid lubricated bearings operated with extreme working performances——a comprehensive review

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

International Journal of Extreme manufacturing 2024年第2期6卷 325-376页

作者： Guohua Zhang Ming Huang Gangli Chen Jiasheng Li Yang Liu Jianguo He Yueqing Zheng Siwei Tang Hailong Cui Institute of Machinery manufacturing technology China Academy of Engineering PhysicsMianyangSichuan 621999People’s Republic of China

Fluid lubricated bearings have been widely adopted as support components for high-end equipment in metrology,semiconductor devices,aviation,strategic defense,ultraprecision manufacturing,medical treatment,and power *** all these applications,the equipment must deliver extreme working performances such as ultraprecise movement,ultrahigh rotation speed,ultraheavy bearing loads,ultrahigh environmental temperatures,strong radiation resistance,and high vacuum operation,which have challenged the design and optimization of reliable fluid lubricated *** of any related bottlenecks will promote the development course of high-end *** promote the advancement of high-end equipment,this paper reviews the design and optimization of fluid lubricated bearings operated at typical extreme working performances,targeting the realization of extreme working performances,current challenges and solutions,underlying deficiencies,and promising developmental *** paper can guide the selection of suitable fluid lubricated bearings and optimize their structures to meet their required working performances.

关键词： fluid lubricated bearings structural design performance optimization extreme working performances

Artificial intelligence-assisted design of new chemical materials: a perspective

在线全文

学校读者我要写书评

暂无评论

Science China(Information Sciences) 2024年第8期67卷 334-336页

作者： Feng QIAN Wenli DU Weimin ZHONG Yang TANG Jingyi LU Key Laboratory of Smart manufacturing in Energy Chemical Process Ministry of EducationEast China University of Science and Technology

New chemical materials are a fresh category of substances created through chemical reactions or by refining existing materials through secondary processes. By using creative methods, advanced technologies, innovative techniques, and state-of-the-art equipment, these materials(e.g., high-end polyolefin, nano materials) [1] are carefully designed and developed to showcase outstanding performance and unique capabilities beyond what traditional chemical materials can offer [2].

关键词：

同方期刊数据库

Physicochemical principles of hydrogen metallurgy in blast furnace

在线全文

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第1期31卷 46-63页

作者： Han-jie Guo School of Metallurgical and Ecological Engineering University of Science and Technology BeijingBeijing100083China Beijing Key Laboratory of Special Melting and Preparation of High-end Metal Materials Beijing100083China

Based on the stoichiometric method and the free energy minimization method,an ideal model for the reduction of iron oxides by carbon and hydrogen under blast furnace conditions was established,and the reduction efficiency and theoretical energy consumption of the all-carbon blast furnace and the hydrogen-rich blast furnace were *** results show that after the reduction reaction is completed at the bottom of the blast furnace,the gas produced by reduction at 1600℃still has a certain excessive reduction capacity,which is due to the hydrogen brought in by the hydrogen-rich blast as well as the excess carbon monoxide generated by the reaction of the coke and the oxygen brought in by the *** the process of the gas with excessive reduction capacity rising from the bottom of the blast furnace and gas reduction process,the excessive reduction capacity of the gas gradually decreases with the increase in the dydrogen content in the *** the all-carbon blast furnace,the excess gas reduction capacity is the strongest,and the total energy consumption per ton of iron reduction is the *** shows that,for the current operation mode of the blast furnace,adding hydrogen in the blast furnace cannot reduce the consumption of carbon required for reduction per ton of iron,but rather increases the consumption of carbon.

关键词： Hydrogen metallurgy Excess gas reduction capacity Theoretical energy consumption Hydrogen-rich blast furnace Thermodynamic model Gibbs minimum free energy method

Effect of slag composition on kinetic behavior of deep deoxidation of 5 wt.% Si high-silicon austenitic stainless steel

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第8期31卷 1873-1885页

作者： Guan-xiong Dou Han-jie Guo Jing Guo Xue-cheng Peng Qing-yun Chen School of Metallurgical and Ecological Engineering University of Science and Technology Beijing(USTB)Beijing 100083China Beijing Key Laboratory of Special Melting and Preparation of High-end Metal Materials Beijing 100083China

Based on a thermodynamic study of 5 wt.%Si high-silicon austenitic stainless steel(SS-5Si)smelting using CaF_(2)-CaO-Al_(2)0_(3)-Mg-Si0_(2) slag to obtain a low oxygen content of less than 10×10^(-4) wt.%,a kinetic mass transfer model for deep deoxidation was established through laboratory studies,and the effects of slag components and temperature on deoxidation during the slag-steel reaction process of sS-5Si were systematically *** experimental data verified the accuracy of the model *** results showed that the final oxygen content in the steel at 1873 K was mainly controlled by the oxygen content derived from the activity of SiO_(2) regulated by the[Si]-[O]equilibrium reaction in the slag system;in particular,when the slag basicity R(R=w(CaO)/w(SiO2),where w(CaO)and w(SiO_(2))are the contents of CaO and SiO_(2) in the slag,respectively)is 3,the Al2O3 content in the slag needs to be less than 2.7%.The mass transfer rate equation for the kinetics of the deoxidation reaction revealed that the mass transfer of oxygen in the liquid metal is the rate-controlling step under different slag conditions at 1873 K,and the oxygen transfer coefficient ko.m increases with increasing the slag basicity from 4.0×10^(-6)m s^(-1)(R=1)to 4.3×10^(-5) m s^(-1)(R=3).ko.m values at R=2 and R=3 are almost the same,indicating that high slag basicity has little *** integral of the mass transfer rate equation for the deoxidation reaction of SS-5Si under different slag conditions is *** total oxygen content of the molten steel decreases with increasing basicity from an initial content of 22×10^(-4) to 3.2×10^(-4) wt.%(R=3),consistent with the change in ko.m with slag *** R=2,the slag-steel reaction takes 15 min to reach equilibrium(w[O]=5.5×10^(-4) wt.%),whereas at R=3,the slag-steel reaction takes 30 min to reach equilibrium(w[0]=3.2×10^(-4) wt.%).Considering the depth of deoxidation and reaction time of SS-5Si smelting,it is recommended the slag b

关键词： Slag-steel reaction Kinetics Rate-controlling step Deep deoxidation Transfer coefficient

Flow Field Simulation and Parameter Analysis of Hydraulic Unbalanced Bionic Self-recovery Actuator for Rotary Equipment

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Bionic Engineering 2024年第1期21卷 325-343页

作者： Wei Li Xin Pan Dehong Ge Jinji Gao Key Laboratory of Engine Health Monitoring-Control and Networking of Ministry of Education Beijing University of Chemical TechnologyBeijing 100029China Beijing Key Laboratory of High-end Mechanical Equipment Health Monitoring and Self-Recovery Beijing University of Chemical TechnologyBeijing 100029China

The rotor is the most important component of rotating machinery,and the vibration produced by its mass unbalance has a serious influence on the secure and steady operation of the machine,so an effective online suppression technology is urgently needed.A new hydraulic unbalanced bionic self-recovery system is introduced,imitating the way of manually repairing faulty *** accomplish the effect of actuator mass redistribution,the technology employs pressurized air to drive the quantitative transfer of liquid in the reservoir cavity at opposite *** can complete the online adjustment of the equipment's balancing state and suppress the unbalanced vibration of equipment in real time,which gives the equipment the ability to maintain an autonomous health state and improve equipment *** composition and working principle of the system are introduced in detail,and the key performance parameters,such as the minimum running speed and the balancing liquid transfer speed,are analyzed *** fluid-solid coupling model of the actuator was established,and the two-phase flow from inside the hydraulic unbalanced bionic self-recovery actuator was simulated under multiple working conditions and the performance parameters were quantitatively analyzed.A balancing simulation test bed was built,and its effectiveness was verified by performance parameter tests and unbalanced bionic self-recovery *** experimental results show that the mass distribution adjustment of the balancing disk can be achieved using different viscosity balancing liquid,and the response of liquid viscosity 10 cSt is faster than that of liquid viscosity 100 cSt in the process of balancing liquid transfer,and the time is reduced by more than 75%;the system can reduce the simulated rotor amplitude from 18.3μm to 10.6μm online in real time,which provides technical support for the subsequent development of a new generation of bionic intelligent equipment.

关键词： Engineering self-recovery-Bionics Simulation analysis Self-recovery regulation

Effects of in-situZrB_2 nanoparticles and scandium on microstructure and mechanical property of 7N01 aluminum alloy

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Rare Earths 2024年第3期42卷 612-620,I0007页

作者： Xizhou Kai Yuhui Wang Ruikun Chen Yanjie Peng Anjun Shi Ran Tao Xiangfeng Liang Guirong Li Gang Chen Xiaojing Xu Yutao Zhao School of Material Science and Engineering Jiangsu UniversityZhenjiang212013China Institute for Advanced manufacturing and Modern Equipment technology Jiangsu UniversityZhenjiang212013China

In this study, the in-situ synthesized ZrB_(2) nanoparticles and rare earth Sc were introduced to enhance the strength and ductility of 7N01 aluminum alloy, via the generation of high-melting and uniform nanodispersoids. The microstructure and mechanical property evolution of the prepared composites and the interaction between ZrB_(2) and Sc were studied in detail. The microstructure investigation shows that the introduction of rare earth scandium(Sc) can promote the distribution of ZrB_(2) nanoparticles, by improving their wettability to the Al melt. Meanwhile, the addition of rare earth Sc also modifies the coarse Al Zn Mg Mn Fe precipitated phases, refines the matrix grains and generates high-melting Al_3(Sc,Zr)/Al_3Sc nanodispersoids. Tensile tests of the composites show that with the combinatorial introduction of ZrB_(2) and Sc, the strength and ductility of the composites are improved simultaneously compared with the corresponding 7N01 alloy, ZrB_(2) /7N01 composite and Sc/7N01 alloy. And the optimum contents of ZrB_(2) and Sc are 3 wt% and 0.2 wt% in this study. The yield strength, ultimate strength and elongation of(3 wt% ZrB_(2) +0.2 wt% Sc)/7N01 composite are 477 MPa, 506 MPa and 9.8%, increased about 18.1%, 12.2%and 38% compared to 7N01 alloy. Furthermore, the cooperation strengthening mechanisms of ZrB_(2) and Sc are also discussed.

关键词： 7N01 aluminum alloy In-situ ZrB_(2)nanoparticles Rare earth Sc Microstructure Mechanical property Mechanism