检索结果-南通市图书馆

Design Improvements and Validation of a Novel Fully 3D Printed Analogue Lumbar Spine Motion Segment

Journal of Bionic Engineering 2024年第3期21卷 1388-1396页

作者： Siril Teja Dukkipati Mark Driscoll Musculoskeletal Biomechanics Research Lab Department of Mechanical EngineeringMcGill University845 Sherbrooke St.W(163)MontréalQCH3A 0C3Canada Orthopaedic Research Lab Montreal General Hospital1650 Cedar Ave(LS1.409)MontréalQCH3G 1A4Canada

Spine biomechanical testing methods in the past few decades have not evolved beyond employing either cadaveric studies or finite element modeling ***,both these approaches may have inherent cost and time *** studies are the present gold standard for spinal implant design and regulatory approval,but they introduce significant variability in measurements across patients,often requiring large sample *** element modeling demands considerable expertise and can be computationally expensive when complex geometry and material nonlinearity are *** analogue spine models could complement these traditional methods as a low-cost and high-fidelity alternative.A fully 3D printable L-S1 analogue spine model with ligaments is developed and validated in this *** stiffness of the model under pure bending loading in flexion-extension,Lateral Bending(LB)and Axial Rotation(AR)is evaluated and compared against historical ex vivo and in silico ***,the effect of interspinous,intertransverse ligaments and the Thoracolumbar Fascia(TLF)on spinal stiffness is evaluated by systematic construction of the *** flexion,model Range of Motion(ROM)was 12.92±0.11°(ex vivo:16.58°,in silico:12.96°)at *** LB,average ROM was 13.67±0.12°at 7.5 Nm(ex vivo:15.21±1.89°,in silico:15.49±0.23°).Similarly,in AR,average ROM was 17.69±2.12°at 7.5Nm(ex vivo:14.12±0.31°,in silico:15.91±0.28°).The addition of interspinous and intertransverse ligaments increased both flexion and LB stiffnesses by approximately 5%.Addition of TLF showed increase in flexion and AR stiffnesses by 29%and 24%,*** novel model can reproduce physiological ROMs with high repeatability and could be a useful open-source tool in spine biomechanics.

关键词： Lumbar spine 3D printing Intervertebral disc Biomechanical testing Spine mechanics

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Control of electromechanical performance in 3D printing latticestructured BaTiO_(3) piezoelectric ceramics

引用

Journal of Advanced Ceramics 2024年第7期13卷 987-1001页

作者： Zhujun Jiang Yinghong Sun Jimin Chen Yong Zeng Faculty of Materials and Manufacturing Beijing University of TechnologyBeijing 100124China Beijing Engineering Research Center of 3D Printing for Digital Medical Health Beijing University of TechnologyBeijing 100124China

Barium titanate(BaTiO_(3))piezoelectric ceramics with triply periodic minimal surface(TPMS)structures have been frequently used in filters,engines,artificial bones,and other fields due to their high specific surface area,high thermal stability,and good heat ***,only a limited number of studies have analyzed the effect of various parameters,such as different wall thicknesses and porosities of TPMS structures,on ceramic electromechanical *** this study,we first employed vat photopolymerization(VPP)three-dimensional(3D)printing technology to fabricate high-performance BaTiO_(3) *** investigated the slurry composition design and forming process and designed a stepwise sintering postprocessing technique to achieve a density of 96.3%and a compressive strength of 250±25 MPa,with the piezoelectric coefficient(d_(33))reaching 263 pC/***,we explored the influence of three TPMS structures,namely,diamond,gyroid,and Schwarz P,on the piezoelectric and mechanical properties of BaTiO_(3) ceramics,with the gyroid structure identified as exhibiting optimal ***,we examined the piezoelectric and mechanical properties of BaTiO_(3) ceramics with the gyroid structure of varying wall thicknesses and porosities,thus enabling the modulation of ceramic electromechanical performance.

关键词： three-dimensional(3D)printing piezoelectric ceramics porous structure mechanical properties electrical properties

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Attitude control of multi-spacecraft systems on SO(3)with stochastic links failure

引用

Chinese Journal of Aeronautics 2024年第3期37卷 320-331页

作者： KANG Zeyu SHEN Qiang WU Shufan Chris J.DAMAREN MU Zhongcheng School of Aeronautics and Astronautics Shanghai Jiao Tong UniversityShanghai 200240China Institute for Aerospace Studies University of TorontoTorontoOntario M3H 5T6Canada

In this paper,for Multi-Spacecraft System(MSS)with a directed communication topology link and a static virtual leader,a controller is proposed to realize attitude consensus and attitude stabilization with stochastic links failure and actuator ***,an MSS attitude error model suitable for a directed topology link and with a static virtual leader based on SO(3)is derived,which considers that the attitude error on SO(3)cannot be defined based on algebraic ***,we design a controller to realize the MSS on SO(3)with attitude consensus and attitude stabilization under stochastic links failure and actuator ***,the simulation results of a multi-spacecraft system with stochastic links failure and a static virtual leader spacecraft are demonstrated to illustrate the efficiency of the attitude controller.

关键词： Multi-spacecraft systems Attitude consensus Attitude stabilization Stochastic links failure Super-martingale convergence

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

GPU-accelerated OCT imaging: Real-time data processing and artifact suppression for enhanced monitoring of 3D bioprinted tissues and vascular-like networks

引用

Journal of Innovative Optical Health Sciences 2024年第6期17卷 67-82页

作者： Shanshan Yang Jinhao Zhou Hao Guo Ling Wang Mingen Xu Hangzhou Dianzi University Automation College HangzhouZhejiangP.R.China Zhejiang Provincial Key Laboratory of Medical Information and Biological 3D Printing Hangzhou ZhejiangP.R.China

Optical coherence tomography(OCT)imaging technology has significant advantages in in situ and noninvasive monitoring of biological ***,it still faces the following challenges:including data processing speed,image quality,and improvements in three-dimensional(3D)visualization *** technology,especially functional imaging techniques like optical coherence tomography angiography(OCTA),requires a long acquisition time and a large data *** the substantial increase in the acquisition speed of swept source optical coherence tomography(SS-OCT),it still poses significant challenges for data ***,during in situ acquisition,image artifacts resulting from interface reflections or strong reflections from biological tissues and culturing containers present obstacles to data visualization and further ***,a customized frequency domainfilter with anti-banding suppression parameters was designed to suppress artifact ***,this study proposed a graphics processing unit(GPU)-based real-time data processing pipeline for SS-OCT,achieving a measured line-process rate of 800 kHz for 3D fast and high-quality data ***,a GPU-based realtime data processing for CC-OCTA was integrated to acquire dynamic ***,a vascular-like network chip was prepared using extrusion-based 3D printing and sacrificial materials,with sacrificial material being printed at the desired vascular network locations and then removed to form the vascular-like *** imaging technology was used to monitor the progression of sacrificial material removal and vascular-like network ***,GPU-based OCT enables real-time processing and visualization with artifact suppression,making it particularly suitable for in situ noninvasive longitudinal monitoring of 3D bioprinting tissue and vascular-like networks in microfluidic chips.

关键词： SS-OCT GPU acceleration artifact noise 3D bioprinted microfluidic chip.

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Process,Material,and Regulatory Considerations for 3D Printed Medical Devices and Tissue Constructs

引用

Engineering 2024年第5期36卷 146-166页

作者： Wei Long Ng Jia An Chee Kai Chua Singapore Centre for 3D Printing(SC3DP) School of Mechanical and Aerospace EngineeringNanyang Technological UniversitySingapore 639798Singapore Centre for Healthcare Education Entrepreneurship and Research@SUTD(CHEERS)Singapore University of Technology and DesignSingapore 487372Singapore

Three-dimensional(3D)printing is a highly automated platform that facilitates material deposition in a layer-by-layer approach to fabricate pre-defined 3D complex structures on *** is a highly promising technique for the fabrication of personalized medical devices or even patient-specific tissue *** type of 3D printing technique has its unique advantages and limitations,and the selection of a suitable 3D printing technique is highly dependent on its intended *** this review paper,we present and highlight some of the critical processes(printing parameters,build orientation,build location,and support structures),material(batch-to-batch consistency,recycling,protein adsorption,biocompatibility,and degradation properties),and regulatory considerations(sterility and mechanical properties)for 3D printing of personalized medical *** goal of this review paper is to provide the readers with a good understanding of the various key considerations(process,material,and regulatory)in 3D printing,which are critical for the fabrication of improved patient-specific 3D printed medical devices and tissue constructs.

关键词： 3D printing Bioprinting Biofabrication Medical devices Tissue constructs

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

High-performance Bi_(2)S_(3)/ZnO photoanode enabled by interfacial engineering with oxyanion for efficient photoelectrochemical water oxidation

引用

Nano Research 2024年第7期17卷 5996-6005页

作者： Ying-Chu Chen Hsiang-Yu Jui Yichen Feng Yun-Hsiang Lu Yu-Kuei Hsu Department of Chemical Engineering&Biotechnology "National Taipei University of Technology"No.1Sec.3Zhong-Xiao E.Rd.Da'an Dist.Taipei City 10608TaiwanChina Department of Opto-Electronic Engineering "National Dong Hwa University"No.1Sec.2Da Hsueh RoadShoufengHualien 97401TaiwanChina China-UK Low Carbon College Shanghai Jiao Tong UniversityNo.3Yinlian RoadLingangShanghai 201306China

In the present contribution,we demonstrate that the sluggish kinetics of oxygen evolution reaction(OER)over the bismuth sulfide(Bi_(2)S_(3))photoanode,which severely restricts its photoelectrochemical activity,is markedly accelerated by employing a sulfatecontaining ***-principle calculation points to the spontaneous adsorption of sulfate(SO_(4)^(2−))on Bi_(2)S_(3)and its capacity of stabilizing the OER intermediates through hydrogen bonding,which is further reinforced by increasing the local density of states near the Fermi level of Bi_(2)S_(3).Meanwhile,the electron transfer is also promoted to synergistically render the ratedetermining step(from O*to OOH*)of OER over Bi_(2)S_(3)kinetically *** but not least,benefitting from such enhanced OER activity and efficient charge separation resulted from depositing Bi_(2)S_(3)on the zinc oxide nanorods(ZnO NRs),forming a core–shell heterojunction,its photocurrent density achieves 8.61 mA·cm^(−2)at 1.23 VRHE,far surpassing those reported for additional Bi_(2)S_(3)-based and several state-of-the-art photoanodes in the literature and further exceeding their theoretical *** great promise of the Bi_(2)S_(3)/ZnO NRs is in view of such outperformance,the superior Faradaic yield of oxygen of more than~80%and the outstanding half-cell applied bias photon-to-current efficiency of~1%well corroborated.

关键词： photoelectrochemical water oxidation oxyanion adsorption electronic structure regulation oxygen evolution reaction(OER)intermediates stabilization Bi_(2)S_(3)

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

A new portable open-path instrument for ambient NH_(3) and on-road emission measurements

引用

Journal of Environmental Sciences 2024年第2期136卷 606-614页

作者： Wenhao Dai Shanshan Wang Sanbao Zhang Jian Zhu Chuanqi Gu Zhibin Sun Ruibin Xue Bin Zhou Shanghai Key Laboratory of Atmospheric Particle Pollution and Prevention(LAP3) Department of Environmental Science and EngineeringFudan UniversityShanghai 200438China Institute of Eco-Chongming(IEC) Shanghai 202162China Institute of Atmospheric Sciences Fudan UniversityShanghai 200433China

Increased attentions to vehicle emission of NH_(3)have been paid since it is generally regarded as an important source in urban ***,we developed a movable instrument based on Differential Optical Absorption Spectroscopy(DOAS)principle for detecting on-road NH_(3),which can avoid the losses in the sampling process attributed to the non-sampling *** this mobile DOAS,the temporal resolution,detection limit and relative error for NH_(3)were 1 min,2.29 ppbv and 4.57%±2.44%,*** employed to the on-road measurements along the arterial highway in Shanghai,the spatial distributions of NH_(3)and NO were obtained,and their dependence of traffic and road conditions were *** slopes of linear regression between NH_(3)and NO were 0.40,0.02 and 0.07 on the Middle Ring Road,Outer Ring Road and Chongming Island Ring *** indicates that light gasoline vehicles(LGVs)were found to be the main contributor to NH_(3)emissions,while heavy-duty diesel vehicles(HDVs)mainly emitted *** on the measured NH_(3)in the tunnel,the mileagebased NH_(3)emission factor per vehicle was estimated to be 17.9±6.3 mg/*** reported open-path instrument can be broadly used in on-road pollutant monitoring or vehicle emissions,and the measurements can reveal the real situation of emission characteristics,even find the abnormal operations of vehicle catalyst system.

关键词： Ammonia Traffic emissions DOAS Emission factor Mobile measurements

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Gradient layered MXene/Fe_(3)O_(4)@CNTs/TOCNF ultrathin nanocomposite paper exhibiting effective electromagnetic shielding and multifunctionality

引用

Nano Research 2024年第9期17卷 8233-8242页

作者： Zhengkun Ma Jingzong He Shilin Liu Xiaoxuan Qie Meiheng Gan Ruonan Cheng Qilin Wu Malcolm Xing State Key Laboratory for Modification of Chemical Fibers and Polymer Materials College of Materials Science and EngineeringDonghua UniversityShanghai 201620China College of Chemistry and Chemical Engineering Donghua UniversityShanghai 201620China Department of Mechanical Engineering University of ManitobaWinnipegMB R3T 2N2Canada

As wearable electronic devices are rapidly developing,there is an urgent need for lightweight,flexible,and ultrathin multifunctional electromagnetic interference(EMI)shielding ***,the flexible ultrathin paper that combines efficient shielding and multifunctional integration remains a considerable ***,a novel MXene/Fe_(3)O_(4)@CNTs/TOCNF(MCT,MXene=transition metal carbide/carbonitride,CNTs=carbon nanotubes,TOCNF=TEMPO-oxidized cellulose nanofiber,TEMPO=2,2,6,6-tetramethylpiperidine-1-oxyl radical)nanocomposite paper with a multilayer electromagnetic gradient structure and electromagnetic dual losses was successfully prepared by a simple filtration *** from effective gradient design and adjusting the proportion of TOCNF,the composite paper(only 18μm)exhibits outstanding shielding effectiveness(SE)of 66 dB in the X-band,ultrahigh thickness-specific SE and surface-specific SE values of 3300 dB·mm-1 and 31,428 dB·cm^(2)·g^(-1)***,dehydroxylation treatment improves MCT paper's hydrophobicity,environmental stability,and mechanical strength,expanding its range of ***,the highly efficient Joule heating properties and hydrophobicity provide MCT additional de-icing *** also simulated the electromagnetic shielding effects of MCT composite paper,which was applied in *** study documents an innovative and intriguing material combination,providing a simple and effective manufacturing strategy for developing EMI shielding *** paper is highly suitable for outdoor portable or wearable electronic devices and has significant application potential in humid/severe cold environments.

关键词： cellulose fiber thin papers nanocomposites electromagnetic interference(EMI)shielding

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

利用晶体图神经网络和对抗样本方法探索CsSnBr_(3-x)I_(x)中高能量转换效率构型并提高模型的可解释性

引用

Science China Materials 2024年第4期67卷 1183-1191页

作者：王韬赖晓珑卫亚东郭鸿金浩 College of Physics and Optoelectronic Engineering Shenzhen UniversityShenzhen 518060China Centre for the Physics of Materials and Department of Physics McGill UniversityMontreal H3A 2T8Canada

晶体图卷积神经网络(CGCNN)不需要手动创建描述符,因而改变了材料研究方式.然而,它们在可解释性以及对结构畸变的敏感性方面的不足,阻碍了该模型在材料掺杂工程中的应用.因此,我们提出了一种具有创新性的对抗样本方法,用于引导特征构建... 详细信息

晶体图卷积神经网络(CGCNN)不需要手动创建描述符,因而改变了材料研究方式.然而,它们在可解释性以及对结构畸变的敏感性方面的不足,阻碍了该模型在材料掺杂工程中的应用.因此,我们提出了一种具有创新性的对抗样本方法,用于引导特征构建并增强CGCNN的可解释性.在这项研究中,重点是寻找具有高能量转换效率的CsSnBr_(3-x)I_(x)构型.首先,训练了一个CGCNN分类器作为基准.随后,对输入数据进行扰动以生成低性能分类器,并基于错误预测结果来识别对抗样本.将对抗样本与正常样本进行比较,发现对抗样本中存在着明显的结构畸变,这为创建描述符提供了思路.基于此,建立了一个可解释模型,该模型超越了使用原子位置扰动的CGCNN模型以及使用通用特征的梯度提升分类器模型.值得注意的是,之前被忽视的描述符,即“不等价原子数”,在提供关键见解方面发挥了重要作用.进一步研究发现,具有明显畸变的结构可以表现出增强的功率密度,从而提高能量转换效率.本工作不仅阐明了原子替代对能源转换效率的影响,还为构建可解释的机器学习模型提供了可行方案.

关键词：卷积神经网络可解释性对抗样本能量转换效率位置扰动输入数据分类器结构畸变

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Nanodiamond/Ti_(3)C_(2) MXene-coated quartz crystal microbalance humidity sensor with high sensitivity and high quality factor

引用

Rare Metals 2024年第6期43卷 2719-2729页

作者： Yao Yao Qiao Chen Yan-Qi Li Xian-He Huang Wei-Wei Ling Zhe-MiaoXie Jia-QiWang Chang-Ming Chen College of Communication Engineering Chengdu University of Information TechnologyChengdu 610225China School of Automation Chongqing University of Posts and TelecommunicationsChongqing 400065China School of Automation Engineering University of Electronic Science and Technology of ChinaChengdu 611731China Advanced Micro-/Nano-Devices Lab Department of Systems Design EngineeringUniversity of WaterlooWaterlooON N2L 3GlCanada

To address the challenge of achieving both high sensitivity and a high quality factor in quartz crystal microbalance(QCM)humidity sensors,a nanodiamond(ND)/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was *** material characteristics of ND,Ti_(3)C_(2)MXene,and ND/Ti_(3)C_(2)MXene composite were analyzed by transmission electron microscopy(TEM)and Fourier transform infrared(FTIR)*** experimental results demonstrated that the hydrophilic ND nanoparticles coated on Ti_(3)C_(2) MXene nanosheet prevented the self-stacking of Ti_(3)C_(2)MXene and enhanced the sensitivity of Ti_(3)C_(2) MXene-based QCM humidity ***,the high mechanical modulus of Ti_(3)C_(2) MXene material helped ND/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor to achieve a high quality factor(>20,000).ND/Ti_(3)C_(2)MXene compositecoated QCM humidity sensor exhibited a sensitivity of 82.45 Hz/%RH,a humidity hysteresis of 1.1%RH,fast response/recovery times,acceptable repeatability,and good stability from 11.3%RH to 97.3%*** response mechanism of ND/Ti_(3)C_(2) MXene composite-coated QCM humidity sensor was analyzed in combination with a bi-exponential kinetic adsorption ***,the potential application of ND/Ti_(3)C_(2)MXene composite-coated QCM humidity sensor was demonstrated through its frequency response to wooden blocks with different moisture contents.

关键词： Humidity sensor Quartz crystal microbalance Nanodiamond Ti_(3)C_(2)MXene High quality factor

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：