检索结果-南通市图书馆

Advanced Powder Materials 2022年第1期1卷 59-66页

作者： Shang Sui Youxiang Chew Zhiwei Hao Fei Weng Chaolin Tan Zhenglin Du Guijun Bi Singapore Institute of manufacturing Technology A∗STAR73 Nanyang Drive637662Singapore State Key Laboratory of Solidification Processing Northwestern Polytechnical University127 West Youyi RoadBeilin DistrictXi'an Shaanxi710072China Key Laboratory of Metal High Performance additive manufacturing and Innovative Design MIIT ChinaNorthwestern Polytechnical University127 West Youyi RoadBeilin DistrictXi'an Shaanxi710072China

Globularαphases can significantly improve the ductility of titanium *** heat treatment(CHT)has been proved to be an effective way to induce the formation of globularαphases inα+βtitanium alloy Ti-6Al-4V fabricated by laser aided additive manufacturing(LAAM).However,there is no prior research reporting methods for obtaining globularαphases in LAAM-built near-αtitanium *** work investigated the cyclic heat treatment(CHT)procedures suitable for the LAAM-built near-αtitanium alloy Ti-6Al-2Sn-4Zr-2Mo(Ti6242)to attain the globularα*** results show that 980℃ is the most suitable upper temperature limit for ***,it is difficult to achieve a high volume fraction of the globularαphases in the LAAM-built Ti6242 alloys through CHT,which is ascribed to the low composition gradient caused by moreα-stabilizing elements and fewerβ-stabilizing *** as-built sample demonstrated elongation of 6.3%,which is lower than the AMS 4919J standard(elongation≥10%).After 980℃ CHT and 980℃ CHT with solution heat-treatment,the formation of the globularαphases significantly increased the elongation to 13.5%and 12.9%,*** the mechanical strength is reduced after heat-treatment,the room-temperature tensile properties still exceed the AMS 4919J *** examination showed that the as-built sample exhibited a mixed brittle and ductile fracture behavior,while the 980℃ CHT and 980℃ CHT with solution heat-treated samples displayed ductile fracture.

关键词： Cyclic heat treatment Globularαphase Ti6242 alloy laser aided additive manufacturing Room-temperature tensile properties

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Microstructure and mechanical behavior of laser aided additive manufactured low carbon interstitial Fe_(49.5)Mn_(30)Co_(10)Cr_(10)C_(0.5)multicomponent alloy

引用

Journal of Materials Science & Technology 2021年第18期77卷 38-46页

作者： Y.Chew Z.G.Zhu F.Weng S.B.Gao F.L.Ng B.Y Lee G.J.Bi Singapore Institute of manufacturing Technology 73 Nanyang Drive637662Singapore School of Mechanical Aerospace Engineering Nanyang Technological University50 N any ang Avenue639798Singapore

laser aided additive manufacturing(LAAM)was used to fabricate bulk Fe_(49.5)Mn_(30)Co_(10)Cr_(10)C_(0.5)interstitial multicomponent alloy using pre-alloyed *** room temperature yield strength(σ_y),ultimate tensile strength(σ_(UTS))and elongation(ε_(UTS))were 645 MPa,917 MPa and 27.0%*** asbuilt sample consisted of equiaxed and dendritic cellular structures formed by elemental *** cellular structures together with oxide particle inclusions were deemed to strengthen the *** other contributing components include dislocation strengthening,friction stress and grain boundary *** highε_(UTS)was attributed to dislocation motion and activation of both twinning and transformation-induced plasticity(TWIP and TRIP).Tensile tests performed at-40℃and-130℃demonstrated superior tensile strength of 1041 MPa and 1267 MPa ***,almost no twinning was observed in the fractured sample tested at-40℃and-130℃.Instead,higher fraction of strain-induced hexagonal close-packed(HCP)εphase transformation of 21.2%were observed for fractured sample tested at-40℃,compared with 6.3%in fractured room temperature sample.

关键词： Multicomponent alloys laser aided additive manufacturing additive manufacturing Microstructure Mechanical property

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Study of the intrinsic mechanisms of nickel additive for grain refinement and strength enhancement of laser aided additively manufactured Ti–6Al–4V

引用

International Journal of Extreme manufacturing 2022年第3期4卷 132-148页

作者： Shang Sui Youxiang Chew Fei Weng Chaolin Tan Zhenglin Du Guijun Bi Singapore Institute of manufacturing Technology A∗STAR73 Nanyang Drive637662Singapore Institute of Intelligent manufacturing GDASGuangzhou 510070People’s Republic of China

It is well-known that grain refiners can tailor the microstructure and enhance the mechanical properties of titanium alloys fabricated by additive manufacturing(AM). However, the intrinsic mechanisms of Ni addition on AM-built Ti–6Al–4V alloy is not well established. This limits its industrial applications. This work systematically investigated the influence of Ni additive on Ti–6Al–4V alloy fabricated by laser aided additive manufacturing(LAAM). The results showed that Ni addition yields three key effects on the microstructural evolution of LAAM-built Ti–6Al–4V alloy.(a) Ni additive remarkably refines the prior-β grains, which is due to the widened solidification range. As the Ni addition increased from 0 to 2.5 wt. %, the major-axis length and aspect ratio of the prior-β grains reduced from over 1500 μm and 7 to 97.7 μm and1.46, respectively.(b) Ni additive can discernibly induce the formation of globular α phase,which is attributed to the enhanced concentration gradient between the β and α phases. This is the driving force of globularization according to the termination mass transfer theory. The aspect ratio of the α laths decreased from 4.14 to 2.79 as the Ni addition increased from 0 to2.5 wt. %.(c) Ni as a well-known β-stabilizer and it can remarkably increase the volume fraction of β phase. Room-temperature tensile results demonstrated an increase in mechanical strength and an almost linearly decreasing elongation with increasing Ni addition. A modified mathematical model was used to quantitatively analyze the strengthening mechanism. It was evident from the results that the α lath phase and the solid solutes contribute the most to the overall yield strength of the LAAM-built Ti–6Al–4V–x Ni alloys in this work. Furthermore, the decrease in elongation with increasing Ni addition is due to the deterioration in deformability of the β phase caused by a large amount of solid-solution Ni atoms. These findings can accelerate the development of additively manufacture

关键词： Ni addition microstructure refinement laser aided additive manufacturing titanium alloys strengthening mechanism

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：