检索结果-南通市图书馆

Control of Austenite Characteristics and Ferrite Formation Mechanism by Multiple-cyclic annealing in Quenching and Partitioning Steel

引用

Acta Metallurgica Sinica(English Letters) 2022年第7期35卷 1143-1156页

作者： Fei Peng Yunbo Xu Xingli Gu College of Materials Science and Engineering Hunan UniversityChangsha 410082China State Key Laboratory of Rolling and Automation Northeastern UniversityShenyang 110819China Technology Center of Angang Steel Co. Ltd.Anshan 114009China

Quenching and partitioning(Q&P)treatment is a novel method to produce advanced high strength steel with excellent mechanical *** this study,combination of multiple-cyclic annealing and Q&P process was compared with traditional cold-rolled Q&P steel to investigate the microstructural characteristics and austenite *** results showed that retained austenite in traditional Q&P sample was principally located in the exterior of austenite transformation products,while those in multiple-cyclic annealing samples were mainly distributed inside the transformation *** the increase in cyclic annealing number,both of austenite fraction and austenite carbon content increased,attributing to higher initial austenite carbon content and larger number of austenite/neighbored phase interface to act as carbon partitioning *** traditional Q&P sample,the deformed ferrite was recrystallized by sub-grain coalescence,while the austenite was newly nucleated and grew up during annealing *** a comparison,the ferrite in multiple-cycle annealing samples was formed by means of three routes:tempered martensite that completely recovered with retention of interior martensite variant,epitaxial ferrite that formed on basis of tempered martensite,ferrite that newly nucleated and grew up during the final annealing *** of lath martensite and twin martensite were formed as initial martensite and then tempered during partitioning process to precipitateεcarbide with C enrichment,Mn enrichment and homogeneous Si *** with the traditional cold-rolled Q&P steel,the Q&P specimens after multiple-cyclic annealing show smaller strength and much larger elongation,ascribing to the coarser microstructure and more efficient transformation induced plasticity(TRIP)effect deriving from retained austenite with high carbon content and larger volume *** application of double annealing treatment can optimize the mechanical properties of Q&P steel to

关键词： Quenching and partitioning cyclic annealing Ferrite formation Retained austenite

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of cyclic annealing on Microstructure and Mechanical Properties of Medium Carbon Steel

引用

Journal of Iron and Steel Research International 2016年第2期23卷 145-150页

作者： Zhi-qing LÜ Hui-fang ZHANG Qing MENG Zhen-hua WANG Wan-tang FU College of Mechanical Engineering Yanshan UniversityQinhuangdao 066004HebeiChina State Key Laboratory of Metastable Material Science and Technology Yanshan UniversityQinhuangdao 066004HebeiChina

The microstructure and mechanical properties of medium carbon steel after cyclic heat treatment were in- vestigated. The effects of cyclic numbers and long time annealing on the microstructure and mechanical properties of the experimental steel were compared. A short duration （5 min） holding at 1023 K （above A1 temperature） and a short-duration （3 min） holding at 893 K are adopted in each cyclic heat treatment. The spheroidization is accelerated during cyclic heat treatment, and the spheroidizing ratio grows with cyclic numbers. After 12-cycle heat treatments, there are few incompletely spheroidized regions in the specimens, and cementite lamellae mostly change into cement- ite particles. The morphological character of cementite for 12 cycles is similar to that undergoing annealing for 10 h at 973 K. The strength of the experimental steel after 5-cycle heat treatment is the lowest in the following cyclic heat treatment, but it is still higher than that of specimens with subcritical annealing over a long period （10 h）. After 12- cycle heat treatment, the strength of the experimental steel is close to that of the normalized steel, and the plasticity is the best in all heat treated specimens.

关键词： rapid spheroidizing mechanical property cyclic annealing cementite medium carbon steel

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：