检索结果-南通市图书馆

Unsteady-State Grinding Technology (II) Experimental Studies of Grinding Forces and Force Ratio

厦门大学学报（自然科学版） 2002年第S1期41卷 53-54页

作者： LI Zhi-chao, LIN Bin, XU Yan-shen, HU Jun (The State Education Ministry Key Laboratory of High Temperature Structure Ceramics and Machining Technology of Engineering Ceramics, Tianjin University, Tianjin 300072, China)

As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force F n, tangential grinding force F t and a component force acting along the direction of longitudinal feed which is usually neglected because of insignificance. The normal grinding force F n has influence upon surface deformation and roughness of workpiece, while the tangential grinding force F t mainly affect power consumption and service life of grinding wheel. In order to study deep into the process of the unsteady state grinding, we set up a measurement system to monitor the change of grinding force during the course of grinding and try to find some difference in the change of grinding force between the steady state grinding and unsteady state grinding. In the test, the normal and tangential grinding forces, F n and F t were measured by using a set of equipments including sensor, amplifier, oscilloscope and computer monitor. From the results, we can conclude that: 1) In the unsteady state grinding process, the values of the grinding forces are much lower than those of the steady state grinding process and the grinding force ratio showed a nonlinear fluctuation. 2) The tendency of the grinding forces in the process of the unsteady state grinding proved the existence of the cutting and micro-cutting actions. 3) Because the grinding force signals of the unsteady state grinding are much weaker than those of the steady state grinding, to obtain accurate value of the grinding forces, wave filtering is needed to be done. The whole process to filter the perturbation wave can be separated into three steps in order, changing the grinding force signals from analog signals into digital signals, FFT (fast Fourier transform) treatment to the digital signals, and IFFT(inversion fast Fourier transform) treatment to the digital signals after spectrum limitation.

关键词： unsteady state grinding theory grinding force grinding force ratio ceramics common abrasive wheel

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Unsteady-State Grinding Technology (I) Theoretical Generalization and Research on Grinding Mechanism

引用

厦门大学学报（自然科学版） 2002年第S1期41卷 46-47页

作者： LIN Bin, LI Zhi-chao, XU Yan-shen, HU Jun (The State Education Ministry Key Laboratory of High Temperature Structure Ceramics and Machining Technology of Engineering Ceramics, Tianjin University, Tianjin 300072, China)

In conventional grinding theory, it is obvious that there must be a very high hardness difference between grains of the grinding wheel and workpieces. The best grinding wheels are those giving the lowest "natural limiting surface roughness" while cutting at appreciable plunge velocities. With the development of new materials and new machining processes, conventional theories of grinding techniques are no longer suitable to explain many phenomena in the course of grinding procedures. In dealing with precision or ultra-precision grinding processes of advanced ceramics, many results of experiments and practical production have shown that grinding with super hard materials wheels is not the only method to machine advanced ceramics. This paper is intended to propose a new grinding theory named as unsteady-state grinding technique evolved from some phenomena that can not be explained by conventional grinding theory. Unsteady-state grinding technique means the technique which can make the surface roughness of the materials, especially hard and brittle, be up to the standard of ultra-precision machining by utilizing common wheels characteristic of inferior self-sharpening and wear-resistance. In the process of machining, the common wheel need to be redressed about 3～5 times and the time between two redressings is about 3～5 minutes. As a validation of the new grinding technology, experimental work was performed to prove the existence of the unsteady state in the process of ultra-precision grinding with common abrasive wheel-pink fused alumina wheel. From the results of the observation of the wheel topography, the whole grinding process in unsteady state was separated into three stages namely cutting by grains peaks, micro-cutting by micro edges of the broken grains and rubbing without material removal, which is different from conventional grinding theory. For the difference of hardness between grinding wheel and workpiece material is not so apparent, some people have doubts

关键词： unsteady state grinding theory grinding mechanism common abrasive wheel ceramic

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

语言

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

语言

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：