检索结果-南通市图书馆

From concept to commercialization:A review of tubular solid oxide fuel cell technology

Journal of Energy Chemistry 2024年第10期97卷 79-109页

作者： Ruyan Chen Yuan Gao Jiutao Gao Huiyu Zhang Martin Motola Muhammad Bilal Hanif Cheng-Xin Li State Key Laboratory for Mechanical Behavior of Materials School of Materials Science and Engineering Xi'an Jiaotong University Department of Inorganic Chemistry Faculty of Natural Sciences Comenius University Bratislava

The reduced sealing difficulty of tubular solid oxide fuel cells(SOFCs) makes the stacking of tubular cell groups relatively easy,and the thermal stress constraints during stack operation are smaller,which helps the stack to operate stably for a long *** special design of tubular SOFC structures can completely solve the problem of high-temperature sealing,especially in the design of multiple single-cell series integrated into one tube,where each cell tube is equivalent to a small electric stack,with unique characteristics of high voltage and low current output,which can significantly reduce the ohmic polarization loss of tubular *** paper provides an overview of typical tubular SOFC structural designs both domestically and *** on the geometric structure of tubular SOFCs,they can be divided into bamboo tubes,bamboo flat tubes,single-section tubes,and single-section flat tube ***,this article provides an overview of commonly used materials and preparation methods for tubular SOFCs,including commonly used materials and preparation methods for support and functional layers,as well as a comparison of commonly used preparation methods for microtubule SOFCs,It introduced the three most important parts of building a fuel cell stack:manifold,current collector,and ceramic adhesive,and also provided a detailed introduction to the power generation systems of different tubular SOFCs,Finally,the development prospects of tubular SOFCs were discussed.

关键词： Geometric structure Preparation methods Stack Support material tubular solid oxide fuel cell

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Evaluation and Model of Performance of A tubular solid oxide fuel cell

引用

Chemical Research in Chinese Universities 2005年第5期21卷 577-582页

作者： JIA Jun-xi SHEN Sheng-qiang Department of Power Engineering Dalian University of Technology Dalian 116024 P. R. China

A simulation model was developed to analyze the steady state and transient operation of a tubular solid oxide fuel cell. The model covers both the electrochemical and the heat transfer models. The electrochemical model deals with the Nernst potential, ohmic polarization, activation polarization, and concentration polarization, while the heat transfer model concerns the heat transfer by conduction, convection and radiation. The numerical results show that the ohmic loss is the dominant one among the three polarizations in a cathode-supported solid oxide fuel cell and in the middle part of a solid oxide fuel cell the temperature is higher than those at both the ends. When the inlet temperature and the flow rates of the fuel and the oxidant are kept constantly, the temperature of the solid structure of the cell will increase due to the increase of power output of the cell from the initial state to the new one.

关键词： tubular solid oxide fuel cell Polarization Electrochemical reaction Heat and mass transfer

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Samaria-doped Ceria Modified Ni/YSZ Anode for Direct Methane fuel in tubular solid oxide fuel cells by Impregnation Method

引用

Chinese Journal of Chemical Physics 2009年第4期22卷 429-434,448页

作者：张龙山高建峰田瑞芬夏长荣中国科学技术大学材料科学与工程系合肥230026

A porous NiO/yttria-stabilized zirconia was prepared by gel casting technique. anode substrate for tubular solid oxide fuel cells Nano-scale samaria-doped ceria （SDC） particles were formed onto the anode substrate to modify the anode microstructure by the impregnation of solution of Sm（NO3）3 and Ce（NO3）3. Electrochemical impedance spectroscopy, current-voltage and current-powder curves of the cells were measured using an electrochemical workstation. Scanning electron microcopy was used to observe the microstructure. The results indicate that the stability of the performance of the cell operated on humidified methane can be significantly improved by incorporating the nano-structured SDC particles, compared with the unmodified cell. This verifies that the coated SDC electrodes are very effective in suppressing catalytic carbon formation by blocking methane from approaching the Ni, which is catalytically active towards methane pyrolysis. In addition, it was found that a small amount of deposited carbon is beneficial to the performance of the anode. The cell showed a peak power density of 225 mW/cm^2 when it was fed with H2 fuel at 700 ℃, but the power density increased to 400 mW/cm^2 when the fuel was switched from hydrogen to methane at the same flow rate. Methane conversion achieved about 90%, measured by gas chromatogram with a 10.0 mL/min flow rate of fuel at 700 ℃. Although the carbon deposition was not suppressed absolutely, some deposited carbon was beneficial for performance improvement.

关键词： tubular solid oxide fuel cell Gel casting Impregnation Methane

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Electrochemical Properties of tubular SOFC Based on a Porous Ceramic Support Fabricated by Phase-Inversion Method

引用

Journal of Materials Science & Technology 2016年第7期32卷 681-686页

作者： Zongying Han Yuhao Wang Zhibin Yang Minfang Han Union Research Center of fuel cell School of Chemical and Environmental Engineering China University of Mining and Technology State Key Laboratory of Power Systems Department of Thermal Engineering Tsinghua University

In this work, a tubular ceramic-supported solid oxide fuel cell （SOFC） was successfully fabricated by a low cost and simple process involving phase-inversion, brush coating and co-sintering. Properties in- cluding sintering behavior, microstructure of the tubular support as well as the electrochemical properties of single cell were investigated. The results show that a porous tubular support with finger-like pores and macrovoids was obtained after phase-inversion process. The tubular support is proved to be gaspermeable after sintering at 1400 ℃ with shrinkage of about 34%. The maximum power density of single tubular SOFC is 100 mW/cm2 and 122 mW/cm2 at 850 ℃ when fed with wet methane and hydrogen, respectively. The current collection, thickness of electrolyte and gas permeability of tubular support should account for the large total resistance. The present tubular design could be expected to deliver a higher voltage for longer support with several segmented-in-series cell stacks.

关键词： Phase-inversion method Ceramic support tubular solid oxide fuel cell Segmented-in-series

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：