检索结果-南通市图书馆

Secure resource allocation against colluding eavesdropping in a user-centric cell-free massive multiple-input multiple-output system

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Frontiers of Information Technology & Electronic Engineering 2024年第4期25卷 500-512页

作者： Na LI Yuanyuan GAO Kui XU Xiaochen XIA Huazhi HU Yang LI Yueyue ZHANG College of Communication Engineering Army Engineering University of PLANanjing 210007China

We investigate the resource allocation problem of a cell-free massive multiple-input multiple-output system under the condition of colluding eavesdropping by multiple passive *** address the problem of limited pilot resources,a scheme is proposed to allocate the pilot with the minimum pollution to users based on access point selection and optimize the pilot transmission power to improve the accuracy of channel *** at the secure transmission problem under a colluding eavesdropping environment by multiple passive eavesdroppers,based on the local partial zero-forcing precoding scheme,a transmission power optimization scheme is formulated to maximize the system’s minimum security spectral *** results show that the proposed scheme can effectively reduce channel estimation error and improve system security.

关键词： Cell-free Colluding eavesdropping Limited pilot resources Access point selection Security rate

Simple chemical synthesis and isotropic negative thermal expansion in MHfF_(6)(M=Ca,Mn,Fe,and Co)

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Nano Research 2024年第3期17卷 2195-2203页

作者： Yongqiang Qiao Sen Zhang Peixian Zhang Juan Guo Andrea Sanson Xi Zhen Kaiyue Zhao Qilong Gao Jun Chen Key Laboratory of Materials Physics of Ministry of Education and School of Physics and MicroelectronicsZhengzhou UniversityZhengzhou 450052China Department of Physics and Astronomy University of PadovaPadova I-35131Italy Beijing Advanced Innovation Center for Materials Genome Engineering Department of Physical ChemistryUniversity of Science and Technology BeijingBeijing 100083China

The rapid progress of modern technologies has accelerated the prominence of thermal expansion mismatch between materials,and tunable thermal expansion materials will be a powerful safeguard against this ***,isotropic MHfF_(6)(M=Ca,Mn,Fe,and Co)compounds with tunable thermal expansion have been produced via a low-cost synthetic method and *** utilizing temperature dependent X-ray diffraction(XRD)and Raman spectroscopy,combined with first principles calculations,it was revealed that the transverse thermal vibrations of the F atoms are dominated by low-frequency phonons with negative Grüneisen parameters and are therefore the origin of the negative thermal expansion(NTE).Very interestingly,with the increase of the M atomic number,the metal…F atomic linkages become stiffer,reducing the number of vibrational modes with negative Grüneisen parameters,so that the strong NTE can be gradually adjusted to moderate NTE and to near zero thermal *** present study achieves the tunable thermal expansion in a new compound family and shed light on the internal mechanism from the perspective of lattice vibrational dynamics.

关键词： negative thermal expansion fluorides chemical synthesis nanosheet structure first principles calculations

Tetrathiafulvalene esters with high redox potentials and improved solubilities for non-aqueous redox flow battery applications

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Green Energy & Environment 2024年第5期9卷 899-908页

作者： Weikang Hu Jiaqi Xu Nanjie Chen Zongcai Deng Yuekun Lai Dongyang Chen College of Materials science and Engineering Fuzhou UniversityFuzhou350116China College of Chemical Engineering Fuzhou UniversityFuzhou350116China

The exploitation of high performance redox-active substances is critically important for the development of non-aqueous redoxﬂow ***,three tetrathiofulvalene(TTF)derivatives with different substitution groups,namely TTF diethyl ester(TTFDE),TTF tetramethyl ester(TTFTM),and TTF tetraethyl ester(TTFTE),are prepared and their energy storage properties are *** has been found that the redox potential and solubility of these TTF derivatives in conventional carbonate electrolytes increases with the number of ester *** battery with a catholyte of 0.2 mol L^(-1) of TTFTE delivers a speciﬁc capacity of more than 10 Ah L^(-1) at the current density of 0.5 C with two discharge voltage platforms locating at as high as 3.85 and 3.60 V ***/Liþ.Its capacity retention can be improved from 2.34 Ah L^(-1) to 3.60 Ah L^(-1) after 100 cycles by the use of an anion exchange membrane to block the crossover of TTF *** excellent cycling stability of the TIF esters is supported by their well-delocalized electrons,as revealed by the density function theory ***,the introduction of more and larger electron-withdrawing groups is a promising strategy to simultaneously increase the redox-potential and solubility of redox-active ma-terials for non-aqueous redoxﬂow batteries.

关键词： Non-aqueous redox flow batteries Tetrathiofulvarene Redox potential Solubility Substituent effect

Enhancement of–OH content on mechanical properties of antiperovskite solid electrolytes

在线全文

学校读者我要写书评

暂无评论

Nano Research 2024年第7期17卷 6139-6146页

作者： Zunqiu Xiao Huaying Wang Ningyuan Cai Yutong Li Kejia Xiang Wei Wei Tao Ye Zhongtai Zhang Shitong Wang Zilong Tang State Key Lab of New Ceramics and Fine Processing School of Materials Science and EngineeringTsinghua UniversityBeijing 100084China College of New Energy Advanced Chemical Engineering and Energy Materials Research CenterChina University of Petroleum(East China)Qingdao 266580China Department of Nuclear science and Engineering Massachusetts Institute of TechnologyCambridgeMA 02139USA

All-solid-state batteries,renowned for their enhanced safety and high energy density,have garnered broad *** solid electrolytes are highly anticipated for their balanced ***,their high Young’s modulus and inadaptability to volume change during cycling lead to poor contact and eventual battery *** this work,Young’s modulus of Li_(1+x)(OH)_(x)Cl samples is lowered to a level comparable to that of sulfide by regulating the–OH *** the–OH content increases,Young’s modulus of Li_(1+x)(OH)_(x)Cl samples decreases *** may be due to the local aggregation of–OH groups,forming cavities similar to LiOH structure,which reduces the bonding of the *** the premise of high Li-ion conductivity and electrochemical stability,the lowered Young’s modulus improves the contact between the solid electrolyte and the electrodes,forming a strong and stable interfacial layer,thereby improving interfacial and cycling *** symmetrical lithium metal cell shows excellent cycle performance of 600 h,and the assembled LiFePO_(4)|Li_(2.4)(OH)1.4Cl|Li cell shows significantly enhanced cycling endurance with 80%capacity retention after 150 *** work not only emphasizes the crucial importance of Young’s modulus in improving interface issues but also offers innovative approaches to advance the mechanical properties of solid electrolytes.

关键词： mechanical properties -OH content anti-perovskite solid electrolytes Li-ion batteries

Alkyl chain modulation of asymmetric hexacyclic fused acceptor synergistically with wide bandgap third component for high efficiency ternary organic solar cells

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 2024年第7期31卷 1713-1719页

作者： Shufang Li Huilan Guan Can Zhu Chaoyuan Sun Qingya Wei Jun Yuan Yingping Zou College of Chemistry and Chemical Engineering Central South UniversityChangsha 410083China Beijing national Laboratory for Molecular sciences CAS Key Laboratory of Organic SolidsInstitute of ChemistryChinese Academy of SciencesBeijing 100190China Institute of Carbon Neutrality and New Energy School of Electronics and InformationHangzhou Dianzi UniversityHangzhou 310018China

Herein,two asymmetric hexacyclic fused small molecule acceptors(SMAs),namely BP4F-HU and BP4F-UU,were *** elongated outside chains in the BP4F-UU molecule played a crucial role in optimizing the morphology of blend film,thereby improving charge mobility and reducing energy loss within the corresponding ***,the PM6:BP4F-UU device exhibited a higher open-circuit voltage(V_(oc))of 0.878 V compared to the PM6:BP4F-HU device with a V_(oc)of 0.863 ***,a new wide bandgap SMA named BTP-TA was designed and synthesized as the third component to the PM6:BP4F-UU host binary devices,which showed an ideal complementary absorption spectrum in PM6:BP4F-UU *** addition,BTP-TA can achieve efficient intermolecular energy transfer to BP4F-UU by fluorescence resonance energy transfer(FRET)pathway,due to the good overlap between the photoluminescence(PL)spectrum of BTP-TA and the absorption region of ***,ternary devices with 15wt%BTP-TA exhibits broader photon utilization,optimal blend morphology,and reduced charge recombination compared to the corresponding binary ***,PM6:BP4F-UU:BTP-TA ternary device achieved an optimal power conversion efficiency(PCE)of 17.83%with simultaneously increased V_(oc)of 0.905 V,short-circuit current density(J_(sc))of 26.14 mA/cm^(2),and fill factor(FF)of 75.38%.

关键词： asymmetric hexacyclic acceptor outside chain wide bandgap acceptor ternary organic solar cells

Catalytic anode surface enabling in situ polymerization of gel polymer electrolyte for stable Li metal batteries

在线全文

学校读者我要写书评

暂无评论

Nano Research 2024年第6期17卷 5216-5223页

作者： Guocheng Li Kang Liang Yuanjian Li Xiangrui Duan Lin Fu Zhao Cai Zhaofu Zhang Jiangnan Dai Yongming Sun Wuhan national Laboratory for Optoelectronics Huazhong University of Science and TechnologyWuhan 430074China The Institute of Technological sciences Wuhan UniversityWuhan 430074China Faculty of Materials science and Chemistry China University of Geoscience(Wuhan)Wuhan 430074China

Employing quasi-solid-state gel polymer electrolyte(GPE)instead of the liquid counterpart has been regarded as a promising strategy for improving the electrochemical performance of Li metal ***,the poor and uneven interfacial contact between Li metal anode and GPE could cause large interfacial resistance and electrochemical Li stripping/plating inhomogeneity,deteriorating the electrochemical ***,we proposed that the functional component of composite anode could work as the catalyst to promote the in situ polymerization reaction,and we experimentally realized the integration of polymerized-dioxolane electrolyte and Li/Li_(22)Sn_(5)/LiF composite electrode with low interfacial resistance and good stability by in situ catalyzation ***,the reaction kinetics and stability of metallic Li anode were significantly *** a demonstration,symmetric cell using such a GPE-Li/Li_(22)Sn_(5)/LiF integration achieved stable cycling beyond 250 cycles with small potential hysteresis of 25 mV at 1 mA·cm^(−2)and 1 mAh·cm^(−2),far outperforming the counterpart regular GPE on pure *** with LiNi0.5Co0.3Mn0.2O2,the full cell with the GPE-Li/Li_(22)Sn_(5)/LiF integration maintained 85.7%of the original capacity after 100 cycles at 0.5 C(1 C=200 mA·g^(−1)).Our research provides a promising strategy for reducing the resistance between GPE and Li metal anode,and realizes Li metal batteries with enhance electrochemical performance.

关键词： catalyzation polymerization interface resistance interfacial stability Li metal batteries electrochemical performance

Ultrahard X-ray multifunctional application beamline at the SSRF

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Nuclear science and Techniques 2024年第6期35卷 14-25页

作者： Ke Yang Zhao-Hui Dong Chun-Yin Zhou Zi-Long Zhao Dong-Xu Liang Sai-Chao Cao Ai-Guo Li Shanghai Advanced Research Institute Chinese Academy of SciencesShanghai 201210China

The ultrahard X-ray multifunctional application beamline(BL12SW)is a phase-II beamline project at the Shanghai Syn-chrotron Radiation *** primary X-ray techniques used at the beamline are high-energy X-ray diffraction and imaging using white and monochromatic *** main scientific objectives of ultrahard X-ray beamlines are focused on two research *** is the study of the structural properties of Earth’s interior and new materials under extreme high-temperature and high-pressure conditions,and the other is the characterization of materials and processes in near-real service *** beamline utilizes a superconducting wiggler as the light source,with two diamond windows and SiC discs to filter out low-energy light(primarily below 30 keV)and a Cu filter assembly to control the thermal load entering the subsequent optical *** beamline is equipped with dual *** first was a meridional bending Laue monochromator cooled by liquid nitrogen,achieving a full-energy coverage of 30-162 *** second was a sagittal bending Laue monochromator installed in an external building,providing a focused beam in the horizontal direction with an energy range of 60-120 *** were four experimental hutches:two large-volume press experimental hutches(LVP1 and LVP2)and two engineering material experimental hutches(ENG1 and ENG2).Each hutch was equipped with various near-real service conditions to satisfy different *** example,LVP1 and LVP2 were equipped with a 200-ton DDIA press and a 2000-ton dual-mode(DDIA and Kawai)press,***1 and ENG2 provide in situ tensile,creep,and fatigue tests as well as high-temperature *** June 2023,the BL12SW has been in trial *** is expected to officially open to users by early 2024.

关键词： Shanghai Synchrotron Radiation Facility Ultrahard X-ray High energy diffraction High energy imaging Engineering materials Earth science

Effects of orientation on the fatigue crack growth behaviors of the ZK60 magnesium alloy in air and PBS

在线全文

学校读者我要写书评

暂无评论

Journal of Magnesium and Alloys 2024年第1期12卷 281-294页

作者： Jiaqi Hu Zheng Liu Zuoliang Ning Hong Gao School of Chemical Engineering and Technology Tianjin UniversityTianjin 300072China Tianjin Key Laboratory of Chemical Process Safety and Equipment Technology Tianjin 300072China

Strong anisotropic corrosion and mechanical properties caused by specimen orientations greatly limit the applications of wrought magnesium *** investigate the influences of specimen orientation,the corrosion tests and(corrosion)fatigue crack growth tests were *** rolled and transverse surfaces of the materials show distinct corrosion rate differences in the stable corrosion stage,but the truth is the opposite for the initial stage of *** air,specimen orientations have a significant influence on the plastic deformation mechanisms near the crack tip,which results in different fatigue fracture surfaces and cracking *** with R-T specimens,N-T specimens show a slower fatigue crack growth(FCG)rate in air,which can be attributed to crack closure effects and deformation twinning near the crack *** corrosion environment will not significantly change the main plastic deformation mechanisms for the same type of ***,the FCG rate in phosphate buffer saline(PBS)is one order of magnitude higher than that in air,which is caused by the combined effects of hydrogen-induced cracking and anodic *** to the similar corrosion rates at crack tips,the specimens with different orientations display close FCG rates in PBS.

关键词： Magnesium alloy Orientation Corrosion Fatigue crack growth

Manipulating Nb-doped SrFeO_(3−δ)with excellent performance for proton-conducting solid oxide fuel cells

在线全文

学校读者我要写书评

暂无评论

Journal of Advanced Ceramics 2024年第5期13卷 579-589页

作者： Hailu Dai Hongzhe Du Samir Boulfrad Shoufu Yu Lei Bi Qinfang Zhang School of Materials science and Engineering Yancheng Institute of TechnologyYancheng 224051China College of science&Engineering Hamad Bin Khalifa UniversityDoha 34110Qatar School of Resource Environment and Safety Engineering University of South ChinaHengyang 421001China

Nb-doped SrFeO_(3−δ)(SFO)is used as a cathode in proton-conducting solid oxide fuel cells(H-SOFCs).First-principles calculations show that the SrFe0.9Nb0.1O_(3−δ)(SFNO)cathode has a lower energy barrier in the cathode reaction for H-SOFCs than the Nb-free SrFeO_(3−δ)*** experimental studies show that Nb doping substantially enhances the performance of the SrFeO_(3−δ)***,oxygen vacancies(VO)were introduced into SFNO using the microwave sintering method,further improving the performance of the SFNO *** mechanism behind the performance improvement owing to VO was revealed using first-principles calculations,with further optimization of the SFNO cathode achieved by developing a suitable wet chemical synthesis route to prepare nanosized SFNO *** method significantly reduces the grain size of SFNO compared with the conventional solid-state reaction method,although the solid-state reaction method is generally used for preparing Nb-containing *** a result of defect engineering and synthesis approaches,the SFNO cathode achieved an attractive fuel cell performance,attaining an output of 1764 mW·cm−2 at 700℃ and operating for more than 200 *** manipulation of Nb-doped SrFeO_(3−δ)can be seen as a“one stone,two birds”strategy,enhancing cathode performance while retaining good stability,thus providing an interesting approach for constructing high-performance cathodes for H-SOFCs.

关键词： SrFeO_(3−δ)-(SFO) cathode proton conductor solid oxide fuel cells(SOFCs)