检索结果-南通市图书馆

Bimetallic NiCoP catalysts anchored on phosphorus-doped lignin-based carbon for robust oxygen evolution performance

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Rare Metals 2024年第7期43卷 3084-3095页

作者： ling-Ying-zi Xiong Bo-Wen Liu Lei Du Yue-Kuan Zhou Xu-liang lin Huan Wang Guangdong Engineering Technology Research Center for Sensing Materials&Devices Guangzhou Key Laboratory of Sensing Materials&DevicesSchool of Chemistry and Chemical EngineeringGuangzhou UniversityGuangzhou 510006China School of Chemical Engineering and Light Industry Guangdong University of TechnologyGuangzhou 510006China Guangdong Provincial Laboratory of Chemistry and Fine Chemical Engineering Jieyang Center Jieyang 515200China Sustainable Energy and Environment Thrust Function HubThe Hong Kong University of Science and Technology(Guangzhou)Guangzhou 511400China Division of Emerging Interdisciplinary Areas Department of Mechanical and Aerospace EngineeringThe Hong Kong University of Science and TechnologyHong Kong 999077China State Key Lab of Pulp and Paper Engineering South China University of TechnologyGuangzhou 510640China

Oxygen evolution reaction(OER)catalysts are the key core materials that determine the performance of fuel cells,metal-air batteries,electrolytic water decomposition,and other *** this work,a green lignin-based non-precious metal OER catalyst was prepared by a simple ***,c arboxylated lignin was used to complex Ni and Co in situ,and then they were placed with sodium hypophosphite in the same tube furnace for upstream and downstream high-temperature calcination to construct a lignin carbon-based Ni-Co bimetallic OER catalyst(NiCoP@C).The synthesized catalyst is a porous bimetallic phosphide with a three-dimensional network structure and high-density electrochemical active ***@C exhibited favorable catalytic activity for the oxygen evolution reaction(OER)with overpotential of 280 mV at 10 mA·cm~(-2)and a Tafel slope of 77 mV·dec~(-1).Additionally,it exhibited remarkable durability during *** functional theory(DFT)calculations revealed that by leveraging the distinctive structure of transition metal phosphide nanoparticles incorporated into a reticulated substrate,the NiCoP@C catalyst offered an increased number of active sites for OER catalysis,significantly enhancing its stability during practical *** present study broadens the utilization pathways of biomass to"turn waste into treasure,"aligning the development concept of green sustainable development.

关键词： Oxygen evolution reaction Lignin Carbon-based catalyst Nickel-cobalt bimetal Metal phosphide

Analysis and experimental study on resistance-increasing behavior of composite high efficiency autonomous inflow control device

在线全文

学校读者我要写书评

暂无评论

Petroleum Science 2024年第2期21卷 1290-1304页

作者： liang-liang Dong Yu-lin Zhang School of Mechatronic Engineering Southwest Petroleum UniversityChengdu610500SichuanChina State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation Southwest Petroleum UniversityChengdu610500SichuanChina Oil and Gas Equipment Technology Sharing and Service Platform of Sichuan ProvinceChengdu610500SichuanChina

Bottom water coning is the main reason to reduce the recovery of horizontal bottom water reservoir. By water coning, we mean the oil-water interface changes from a horizontal state to a mound-shaped cone and breaks through to the wellbore. Autonomous inflow control device(AICD) is an important instrument maintain normal production after bottom water coning, however, the resistance increasing ability of the swirl type AICD is insufficient at present, which seriously affects the water control effect. Aiming this problem, this paper designs a multi-stage resistance-increasing and composite type AICD. The separation mechanism of oil-water two phases in this structure, the resistance form of oil-water single phase and the resistance-increasing principle of water phase are analyzed. Establishing the dual-phase multi-stage separation and resistance-increasing model, and verified by measuring the throttling pressure drop and oil-water volume fraction of the AICD, it is found that the composite type AICD has the effect of ICD and AICD at the same time, which can balance the production rate of each well section at the initial stage of production, delay the occurrence of bottom water coning. In the middle and later stages of production, water-blocking can be effectively increased to achieve water control and stable *** structural sensitivity analysis, the influence law of various structural parameters on the water control performance of composite AICD was obtained. The simulation calculation results show that,compared with the existing swirl type AICD, composite AICD has higher sensitivity to moisture content,the water phase throttling pressure drop is increased by 4.5 times on average. The composite AICD is suitable for the entire stage of horizontal well production.

关键词： Water control Flow separation Flow resistance-increasing AICD device Simulation and experiment

Risk of cardiovascular death in patients with hepatocellular carcinoma based on the Fine-Gray model

在线全文

学校读者我要写书评

暂无评论

World Journal of Gastrointestinal Oncology 2024年第3期16卷 844-856页

作者： Yu-liang Zhang zi-Rong Liu Zhi Liu Yi Bai Hao Chi Da-Peng Chen Ya-Min Zhang zi-lin Cui First Central Clinical College Tianjin Medical UniversityTianjin 300070China Department of Hepatobiliary Surgery Tianjin First Central HospitalSchool of MedicineNankai UniversityTianjin 300192China

BACKGROUND Hepatocellular carcinoma(HCC)is one of the most common types of cancers worldwide,ranking fifth among men and seventh among women,resulting in more than 7 million deaths *** the development of medical tech-nology,the 5-year survival rate of HCC patients can be increased to 70%.How-ever,HCC patients are often at increased risk of cardiovascular disease(CVD)death due to exposure to potentially cardiotoxic treatments compared with non-HCC ***,CVD and cancer have become major disease burdens ***,further research is needed to lessen the risk of CVD death in HCC patient *** This study was conducted on the basis of the Surveillance,Epidemiology,and End Results database and included HCC patients with a diagnosis period from 2010 to *** independent risk factors were identified using the Fine-Gray model.A nomograph was constructed to predict the CVM in HCC *** nomograph performance was measured using Harrell’s concordance index(C-index),calibration curve,receiver operating characteristic(ROC)curve,and area under the ROC curve(AUC)***,the net benefit was estimated via decision curve analysis(DCA).RESULTS The study included 21545 HCC patients,of whom 619 died of ***(5 cm:2.090(1.543-2.830),P<0.001],surgery(no)[0.376(0.297-0.476),P<0.001],and chemotherapy(none/unknown)[0.578(0.472-0.709),P<0.001]were independent risk factors for CVD death in HCC *** discrimination and calibration of the nomograph were *** C-index values for the training and validation sets were 0.736 and 0.665,*** AUC values of the ROC curves at 2,4,and 6 years were 0.702,0.725,0.740 in the training set and 0.697,0.710,0.744 in the validation set,*** calibration curves showed that the

关键词： Hepatocellular carcinoma Cardiovascular disease deaths Fine-Gray model Risk factor Nomograph Predict

Rational design and energy catalytic application of high-loading single-atom catalysts

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Rare Metals 2024年第10期43卷 4844-4866页

作者： zi-Wei Deng Yue Liu Jie lin Wen-Xing Chen Energy and Catalysis Center School of Materials Science and EngineeringBeijing Institute of Technology Ningbo Institute of Materials Technology and Engineering Chinese Academy of Science

It is well known that single-atom catalysts(SACs)have become a hot topic in the field of catalysis due to their advantages such as 100% metal atom utilization efficiency,high catalytic activity and selectivity compared with conventional catalysts and nanocatalysts. However, the isolated metal atoms on SACs have thermodynamic instability and tend to agglomerate, which limit their catalytic ***, it is of great significance to synthesize stable and high-loading single-atom catalysts(HLSACs). In this paper,we review the research progress of HLSACs from two aspects:design and application. Firstly, we comprehensively introduce the synthesis strategies of HLSACs, namely, top-down and bottom-up methods. Secondly, we overview the application status of HLSACs in three fields: electrocatalysis, thermal catalysis and photocatalysis. Finally, we summarize the development prospects and challenges of HLSACs.

关键词： Design Electrocatalysis High-loading single-atom catalysts Photocatalysis Thermal catalysis

Mechanical performance of 22SiMn2TiB steel welded with lowtransformation- temperature filler wire and stainless steel filler wire

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第4期31卷 967-981页

作者： zi-dong lin Kai-jie Song Zhen Sun zi-qian Zhu Xue-feng Zhao Constantinos Goulas Wei Ya Xing-hua Yu School of Materials Science and Engineering Beijing Institute of TechnologyBeijing 100081China Beijing Institute of Technology Chongqing Innovation Center Chongqing 401120China Department of Design Production and Management Faculty of Engineering Technology.University of TwenteEnschede 7500 AETheNetherlands Rotterdam Additive Manufacture Fieldlab(RAMLAB) Rotterdam 3089 JWTheNetherlands

TX-80 low-transformation-temperature(LTT)welding wire was used to replace the traditional ER 307Si welding wire to realize the connection of 22SiMn2TiB armor steel in manual overlay *** previously existing issues,such as welding cracks,large welding deformation,and severe welding residual stress,were solved to ensure good strength and ductility *** particular,with the same welding conditions,TX-80 LTT wire eliminates welding *** reduces the welding deformation no matter the base pretreatment of pre-setting angle or no pre-setting *** comparison,it was found that the microstructure at the TX-80 weld is mainly composed of martensite and a small amount of retained *** contrast,the microstructure of the ER 307Si weld consists of a large amount of austenite and a small amount of skeleton-like *** variation trend of residual stress and microhardness from the weld to the base were investigated and compared with the mechanical properties of base *** TX-80 and the ER 307Si tensile samples elongation is 6.76%and 6.01%,while the ultimate tensile strengths are 877 and 667 MPa,*** average impact toughness at room temperature of the ER 307Si weld is 143.9 J/cm^(2),much higher than that of the TX-80 weld,which is only 36.7 J/cm^(2).The relationship between impact and tensile properties with microstructure species and distribution was *** addition,the fracture surface of the tensile and the impact samples was observed and *** dimples,fewer pores,larger radiation zone,and shear lips of TX-80 samples indicate better tensile ductility and worse impact toughness than those of ER 307Si weld.

关键词： Low-transformation-temperature material 22SiMn2TiB steel Welding deformation Residual stress Martensitic transformation Mechanical property

Lithium-induced graphene layer containing Li_(3)P alloy phase to achieve ultra-stable electrode interface for lithium metal anode

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Rare Metals 2024年第2期43卷 562-574页

作者： Jia-Xin Chen Guo-Qiang Zhang Xian-Ying Qin Kui lin zi-Jin Yang Ge-Meng liang Yue Xia Guo-Bin Zhang Hai-Kun Wu Qiu-Chan Cai Hai lin Bao-Hua Li Shenzhen Key Laboratory on Power Battery Safety Research and Shenzhen Geim Graphene Center Tsinghua Shenzhen International Graduate SchoolShenzhen518055China Shenzhen Graphene Innovation Center Co. Ltd.Shenzhen518107China School of Chemical Engineering and Advanced Materials The University of AdelaideAdelaideSA5005Australia Department of Chemistry City University of Hong KongHong Kong990077China

Uncontrolled growth of lithium dendrite will lead to low Coulombic efficiency and poor cycle stability,which hinders the commercialization of lithium metal ***,a novel modified lithium anode with reduced graphene oxide conductive network containing trace lithiophilic phosphorus(P-rGO/Cu)is prepared by electrospraying technique combined with heat treatment *** rGO layer has a concave and undulating conductive structure,which can significantly improve the effective electrical contact between lithium metal and the current collector,speed up the kinetics of interfacial electron transport and reaction,and improve the resistance of the negative electrode to the internal stress caused by volume change of the lithium,which is advantageous for the stability of the SEI *** extremely small and uniformly distributed red phosphorus element avoids the volume change caused by lithiation to the maximum *** two-phase compound Li_(3)P obtained by alloying P with Li can directionally induce the homogeneous nucleation and dense deposition of lithium metal,address the issue of lithium dendrites and extend the cycle life of the *** obtained P-rGO/Cu exhibits excellent electrochemical performance with an average Coulombic efficiency(CE)of 98%at a current density of 1 mA·cm^(−2) for 400 cycles,and the capacity retention rate of the full cell matched with lithium iron phosphate(LFP)is 83%after 400 cycles at 1C.

关键词： Lithium anode Dendrite-free Lithiophilicity Induced nucleation deposition

Dynamics modeling and optimal control for multi-information diffusion in Social Internet of Things

在线全文

学校读者我要写书评

暂无评论

Digital Communications and Networks 2024年第3期10卷 655-665页

作者： Yaguang lin Xiaoming Wang liang Wang Pengfei Wan School of Computer Science Shaanxi Normal UniversityXi'an710119China

As an ingenious convergence between the Internet of Things and social networks,the Social Internet of Things(SIoT)can provide effective and intelligent information services and has become one of the main platforms for people to spread and share ***,SIoT is characterized by high openness and autonomy,multiple kinds of information can spread rapidly,freely and cooperatively in SIoT,which makes it challenging to accurately reveal the characteristics of the information diffusion process and effectively control its *** this end,with the aim of exploring multi-information cooperative diffusion processes in SIoT,we first develop a dynamics model for multi-information cooperative diffusion based on the system dynamics theory in this ***,the characteristics and laws of the dynamical evolution process of multi-information cooperative diffusion are theoretically investigated,and the diffusion trend is *** this basis,to further control the multi-information cooperative diffusion process efficiently,we propose two control strategies for information diffusion with control objectives,develop an optimal control system for the multi-information cooperative diffusion process,and propose the corresponding optimal control *** optimal solution distribution of the control strategy satisfying the control system constraints and the control budget constraints is solved using the optimal control ***,extensive simulation experiments based on real dataset from Twitter validate the correctness and effectiveness of the proposed model,strategy and method.

关键词： Social Internet of Things Information diffusion Dynamics modeling Trend prediction Optimal control

Percutaneous transhepatic stenting for acute superior mesenteric vein stenosis after pancreaticoduodenectomy with portal vein reconstruction:A case report

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

World Journal of Gastrointestinal Surgery 2024年第4期16卷 1195-1202页

作者： Chen lin zi-Yan Wang liang-Bo Dong Zhi-Wei Wang Ze-Hui Li Wei-Bin Wang Department of General Surgery Peking Union Medical College HospitalChinese Academy of Medical Sciences and Peking Union Medical CollegeBeijing 100730China Department of General Surgery Peking Union Medical College HospitalBeijing 100730China Interventional Section Department of RadiologyPeking Union Medical College HospitalChinese Academy of Medical Science and Peking Union Medical CollegeBeijing 100730China

BACKGROUND Percutaneous transhepatic stent placement has become a common strategy for the postoperative treatment of portal vein(PV)/superior mesenteric veins(SMV)stenosis/*** has been widely used after liver transplantation surgery;however,reports on stent placement for acute PV/SMV stenosis after pancreatic surgery within postoperative 3 d are *** SUMMARY Herein,we reported a case of intestinal edema and SMV stenosis 2 d after pancreatic *** patient was successfully treated using stent *** the stenosis resolved after stent placement,complications,including bleeding,pancreatic fistula,bile leakage,and infection,made the treatment highly *** use of anticoagulants was adjusted multiple times to prevent venous thromboembolism and the risk of *** careful treatment,the patient stabilized,and stent placement effectively managed postoperative PV/SMV *** Stent placement is effective and feasible for treating acute PV/SMV stenosis after pancreatic surgery even within postoperative 3 d.

关键词： Pancreaticoduodenectomy Portal vein reconstruction Portal vein stenosis Portal vein stent Case report

Micro segment analysis of supercritical methane thermal-hydraulic performance and pseudo-boiling in a PCHE straight channel

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Petroleum Science 2024年第2期21卷 1275-1289页

作者： Qian Li zi-Jie lin Liu Yang Yue Wang Yue Li Wei-Hua Cai Laboratory of Thermo-Fluid Science and Nuclear Engineering Northeast Electric Power UniversityJilin132000JilinChina School of Energy and Power Engineering Northeast Electric Power UniversityJilin132000JilinChina

The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 *** simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow *** results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were *** calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So hea

关键词： Printed circuit heat exchanger Vaporization Supercritical methane Pseudo-boiling Micro segment analysis