检索结果-南通市图书馆

Static recrystallization behaviors and mechanisms of 7Mo super-austenitic stainless steel with undissolved sigma precipitates during double-stage hot deformation

引用

Journal of Iron and Steel Research(International) 2024年第2期31卷 475-487页

作者： Shi-guang Xu Jin-shan He run-ze zhang Fu-cheng zhang Xi-tao Wang Collaborative Innovation Center of Steel Technology University of Science and Technology BeijingBeijing100083China State Key Laboratory of Metastable Materials Science and Technology Yanshan UniversityQinhuangdao066004HebeiChina Shandong Provincial Key Laboratory for High Strength Lightweight Metallic Materials Advanced Materials InstituteQilu University of Technology(Shandong Academy of Science)Jinan250353ShandongChina

Static recrystallization(SRX)behaviors and corresponding recrystallization mechanisms of 7Mo super-austenitic stainless steel were studied under different deformation conditions.The order of influence of deformation parameters on static recrystallization behaviors,from high to low,is followed by temperature,first-stage strain and strain rate.Meanwhile,the effect of holding time on static recrystallization behaviors is significantly controlled by temperature.In addition,with the increase in temperature from 1000 to 1200°C,the static recrystallization mechanism evolves from discontinuous static recrystallization and continuous static recrystallization(cSRX)to metadynamic recrystallization and cSRX,and finally to cSRX.The cSRX exists at all temperatures.This is because high stacking fault energy(56 mJ m−2)promotes the movement of dislocations,making the deformation mechanism of this steel is dominated by planar slip of dislocation.Large undissolved sigma precipitates promote static recrystallization through particle-stimulated nucleation.However,small strain-induced precipitates at grain boundaries hinder the nucleation of conventional SRX and the growth of recrystallized grains,while the hindering effect decreases with the increase in temperature.

关键词： 7Mo super-austenitic stainless steel Double-stage hot deformation Conventional static recrystallization Metadynamic recrystallization Strain-induced precipitation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Syntheses and properties of associative acrylamide copolymers containing short hydrophobic chains used in a friction reducer for slick-water fracturing

引用

Petroleum Science 2024年第3期21卷 1889-1901页

作者： Ya-Xing Dai Xian-Li zhang Si-Yuan Liu Feng-run-ze zhang Yi-Xi zhang Yu-Tong Sang Jing-Xi Zheng Zhao-Sheng Liu Peng zhang College of Chemistry and Chemical Engineering Chongqing University of Science and Technology College of Ecology and Environment Chongqing Resources and Environmental Protection of University China Property Project Department of Dezhou Mining Property Service Center Shengli Oilfield Company of Sinopec

Two allyldimethylalkyl quaternary ammonium salt（AQAS） monomers, N,N-dimethylallylphenylpropylammonium bromide（AQAS1） and N,N-dimethylallylnonylammonium bromide（AQAS2）, were synthesized and used to prepare modified polyacrylamide materials. Two new drag reducers were synthesized from acrylamide（AM）, sodium acrylate（Na AA） and a cationic modified monomer（AQAS1 or AQAS2） via aqueous solution polymerization, and the copolymers were named P（AM/Na AA/AQAS1） and P（AM/Na AA/AQAS2）, respectively. The structures of the drag reduction agents were confirmed by IR and1H NMR spectroscopies. The molecular weight（Mw） of P（AM/Na AA/AQAS1） was 1.79 × 10～6g/mol. When the copolymer concentration was 1000 mg/L and the flow rate was 45 L/min, in fresh water the highest drag reduction rate was 75.8%, in 10,000 mg/L Na Cl solution the drag reduction rate decreased to 72.9%. The molecular weight of P（AM/Na AA/AQAS2） was 3.17 × 10～6g/mol. When the copolymer concentration was500 mg/L and the flow rate was 45 L/min, the drag reduction rate reached 75.2%, and in 10,000 mg/L Na Cl solution the drag reduction rate was 73.3%, decreased by approximately 1.9%. The drag reduction rate for partially hydrolyzed polyacrylamide（HPAM） was also investigated, and the results showed that the drag reduction rates for 500 and 1000 mg/L HPAM solutions were merely 43.2% and 49.0% in brine, respectively. Compared with HPAM, both of the above copolymers presented better drag reduction capacities.

关键词： Shale gas Slick water Drag reducer Modified monomer Copolymerization

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

DNA methylation markers in the diagnosis and prognosis of common leukemias

引用

Signal Transduction and Targeted Therapy 2020年第1期5卷 2468-2477页

作者： Hua Jiang Zhiying Ou Yingyi He Meixing Yu Shaoqing Wu Gen Li Jie Zhu Ru zhang Jiayi Wang Lianghong Zheng Xiaohong zhang Wenge Hao Liya He Xiaoqiong Gu Qingli Quan Edward zhang Huiyan Luo Wei Wei Zhihuan Li Guangxi Zang Charlotte zhang Tina Poon Daniel zhang Ian Ziyar run-ze zhang Oulan Li Linhai Cheng Taylor Shimizu Xinping Cui Jian-kang Zhu Xin Sun Kang zhang Guangzhou Women and Children’s Medical Center Guangzhou Medical UniversityGuangzhou 510623China Guangzhou Regenerative Medicine and Health Guangdong Laboratory Guangzhou 510005China State Key Laboratory of Oncology Sun Yat-sen University Cancer CenterGuangzhou 510060China Department of Statistics and Institute for Integrative Genome Biology University of California RiversideRiversideCA 92521USA Shanghai Center for Plant Stress Biology Shanghai Institute for Biological SciencesChinese Academy of SciencesShanghai 210602China Faculty of Medicine Macao University of Science and TechnologyTaipaMacaoChina

The ability to identify a specific type of leukemia using minimally invasive biopsies holds great promise to improve the diagnosis,treatment selection,and prognosis prediction of patients.Using genome-wide methylation profiling and machine learning methods,we investigated the utility of CpG methylation status to differentiate blood from patients with acute lymphocytic leukemia(ALL)or acute myelogenous leukemia(AML)from normal blood.We established a CpG methylation panel that can distinguish ALL and AML blood from normal blood as well as ALL blood from AML blood with high sensitivity and specificity.We then developed a methylation-based survival classifier with 23 CpGs for ALL and 20 CpGs for AML that could successfully divide patients into high-risk and low-risk groups,with significant differences in clinical outcome in each leukemia type.Together,these findings demonstrate that methylation profiles can be highly sensitive and specific in the accurate diagnosis of ALL and AML,with implications for the prediction of prognosis and treatment selection.

关键词： diagnosis prognosis acute

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Verteporfin fluorescence in antineoplastic-treated pancreatic cancer cells found concentrated in mitochondria

引用

World Journal of Gastrointestinal Oncology 2024年第3期16卷 968-978页

作者： Ying-Qiao zhang Qing-Hao Liu Lu Liu Peng-Yu Guo run-ze Wang Zhi-Chang Ba Department of Radiology Harbin Medical University Cancer HospitalHarbin 150010Heilongjiang ProvinceChina Department of Digestive Internal Medicine Harbin Medical University Cancer HospitalHarbin 150010Heilongjiang ProvinceChina

BACKGROUND Traditional treatments for pancreatic cancer(PC)are inadequate.Photodynamic therapy(PDT)is non-invasive,and proven safe to kill cancer cells,including PC.However,the mitochondrial concentration of the photosensitizer,such as verteporfin,is key.AIM To investigate the distribution of fluorescence of verteporfin in PC cells treated with antitumor drugs,post-PDT.METHODS Workable survival rates of PC cells(AsPC-1,BxPC-3)were determined with chemotherapy[doxorubicin(DOX)and gemcitabine(GEM)]and non-chemotherapy[sirolimus(SRL)and cetuximab(CTX)]drugs in vitro,with or without verteporfin,as measured via MTT,flow cytometry,and laser confocal microscopy.Reduced cell proliferation was associated with GEM that was more enduring compared with DOX.Confocal laser microscopy allowed observation of GEM-and verteporfin-treated PC cells co-stained with 4’,6-diamidino-2-phenylindole and MitoTracker Green to differentiate living and dead cells and subcellular localization of verteporfin,respectively.RESULTS Cell survival significantly dropped upon exposure to either chemotherapy drug,but not to SRL or CTX.Both cell lines responded similarly to GEM.The intensity of fluorescence was associated with the concentration of verteporfin.Additional experiments using GEM showed that survival rates of the PC cells treated with 10μmol/L verteporfin(but not less)were significantly lower relative to nil verte-porfin.Living and dead stained cells treated with GEM were distinguishable.After GEM treatment,verteporfin was observed primarily in the mitochondria.CONCLUSION Verteporfin was observed in living cells.In GEM-treated human PC cells,verteporfin was particularly prevalent in the mitochondria.This study supports further study of PDT for the treatment of PC after neoadjuvant chemotherapy.

关键词： Photodynamic therapy Pancreatic cancer Verteporfin Mitochondria Chemotherapy Gemcitabine

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Solar evaporation for simultaneous oil-water separation and electricity generation with Janus wood-based absorbers

引用

Frontiers of Environmental Science & Engineering 2024年第2期18卷 13-23页

作者： Yue Yang ze Fu Qi zhang Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse School of Environmental and Biological EngineeringNanjing University of Science&TechnologyNanjing 210094China Key Laboratory of Industrial Ecology and Environmental Engineering(Ministry of Education) School of Environmental Science and TechnologyDalian University of TechnologyDalian 116024China National Laboratory of Solid State Microstructures Collaborative Innovation Center of Advanced MicrostructuresCollege of Engineering and Applied SciencesKey Laboratory of Intelligent Optical Sensing and Manipulation(Ministry of Education)Jiangsu Key Laboratory of Artificial Functional MaterialsNanjing UniversityNanjing 210093China

Oily wastewater from ocean oil spills endangers marine ecosystems and human health. Therefore, developing an effective and sustainable solution for separating oil-water mixtures is urgent. Interfacial solar photothermal evaporation is a promising approach for the complete separation of two-phase mixtures using only solar energy. Herein, we report a carbonized wood-based absorber with Janus structure of comprising a hydrophobic top-layer and an oleophobic bottom-layer for simultaneous solar-driven oil-water separation and electricity generation. Under sunlight irradiation, the rapid evaporation of seawater will induce a separation of oil-water mixtures, and cause a high salt concentration region underlying the interface, while the bottom “bulk water” maintains in a low salt concentration, thus forming a salinity gradient. Electricity can be generated by salinity gradient power. Therefore, oil-water separation efficiency of > 99% and derived extra electricity power of ~0.1 W/m2 is achieved under solar radiation, demonstrating the feasibility of oil-water separation and electricity production synchronously directly using solar energy. This work provides a green and cost-effective path for the separation of oil-water mixtures.

关键词： Oily wastewater Carbonized wood Salinity gradient Electricity generation Solar irradiation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Integrated Active Suspension and Anti-Lock Braking Control for Four-Wheel-Independent-Drive Electric Vehicles

引用

Chinese Journal of Mechanical Engineering 2024年第1期37卷 87-98页

作者： ze Zhao Lei zhang Xiaoling Ding Zhiqiang zhang Shaohua Li Liang Gu National Engineering Research Center for Electric Vehicles Beijing Institute of TechnologyBeijing 100081China State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures Shijiazhuang Tiedao UniversityShijiazhuang 050043China

This paper presents an integrated control scheme for enhancing the ride comfort and handling performance of a four-wheel-independent-drive electric vehicle through the coordination of active suspension system(ASS)and anti-lock braking system(ABS).First,a longitudinal-vertical coupled vehicle dynamics model is established by integrating a road input model.Then the coupling mechanisms between longitudinal and vertical vehicle dynamics are analyzed.An ASS-ABS integrated control system is proposed,utilizing an H∞controller for ASS to optimize load transfer effect and a neural network sliding mode control for ABS implementation.Finally,the effectiveness of the proposed control scheme is evaluated through comprehensive tests conducted on a hardware-in-loop(HIL)test platform.The HIL test results demonstrate that the proposed control scheme can significantly improve the braking performance and ride comfort compared to conventional ABS control methods.

关键词： Four-wheel-independent-drive electric vehicles Active suspension system(ASS) Anti-lock braking system(ABS) Vertical-longitudinal vehicle dynamics

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Micro defects formation and dynamic response analysis of steel plate of quasi-cracking area subjected to explosive load

引用

Defence Technology（防务技术） 2024年第1期31卷 580-593页

作者： Zheng-qing Zhou ze-chen Du Xiao Wang Hui-ling Jiang Qiang Zhou Yu-long zhang Yu-zhe Liu Pei-ze zhang Research Institute of Macro-Safety Science University of Science and TechnologyBeijing100083China School of Civil and Resource Engineering University of Science and Technology BeijingBeijing100083China School of Mechanical Engineering Nantong UniversityNantong226019China China North Industry Advanced Technology Generalization Institute Beijing100089China China Academy of Ordnance Science China

As the protective component,steel plate had attracted extensive attention because of frequently threats of explosive loads.In this paper,the evolution of microstructure and the mechanism of damage in the quasi-cracking area of steel plate subjected to explosive load were discussed and the relationships between micro defects and dynamic mechanical response were revealed.After the explosion experiment,five observation points were selected equidistant from the quasi-cracking area of the section of the steel plate along the thickness direction,and the characteristics of micro defects at the observation points were analyzed by optical microscope(OM),scanning electron microscope(SEM) and electron backscattered diffraction(EBSD).The observation result shows that many slip bands(SBs) appeared,and the grain orientation changed obviously in the steel plate,the two were the main damage types of micro defects.In addition,cracks,peeling pits,grooves and other lager micro defects were appeared in the lower area of the plate.The stress parameters of the observation points were obtained through an effective numerical model.The mechanism of damage generation and crack propagation in the quasicracking area were clarified by comparing the specific impulse of each observation point with the corresponding micro defects.The result shows that the generation and expansion of micro defects are related to the stress area(i.***.the upper compression area,the neutral plane area,and the lower tension area).The micro defects gather and expand at the grain boundary,and will become macroscopic damage under the continuous action of tensile stress.Besides,the micro defects at the midpoint of the section of the steel plate in the direction away from the explosion center(i.***.the horizontal direction) were also studied.It was found that the specific impulse at these positions were much smaller than that in the thickness direction,the micro defects were only SBs and a few micro cracks,and the those decreased with the increase of the distance from the e

关键词： Explosive load Quasi-cracking area Micro defects Steel plate Dynamic response Numerical simulation

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Injection molding of highly filled microcrystalline cellulose/polycaprolactone composites with the aid of reversible Diels-Alder reaction

引用

Journal of Materials Science & Technology 2024年第3期170卷 246-254页

作者： ze Pu Wang WenHong Ruan MinZhi Rong MingQiu zhang Key Laboratory for Polymeric Composite and Functional Materials of MOE GD HPPC LabIGCMESchool of ChemistrySun Yat-Sen UniversityGuangzhou 510275China

To tackle the challenge of producing highly filled polymer composites using the traditional injection molding technique,which is characterized by the fairly high melt viscosity that makes mold filling difficult,the authors propose a solution based on dynamic covalent chemistry.As demonstrated by the proof-of-concept experiments,the 4-arm starshaped polycaprolactone(PCL)oligomers and microcrystalline cel-lulose(MCC)are crosslinked by the reversible Diels-Alder(DA)bonds.The flowability of the compounds greatly decreases due to the dissociation of the intercomponent DA bonds at the retro-reaction tempera-ture,and the networked architecture is reconstructed during cooling as a result of the forward DA reaction.Consequently,the high-loading MCC fillers are well distributed in the matrix and covalently bonded to the nearby PCL,forming a striking contrast to the control in which linear PCL acts as the matrix.The DA bonds crosslinked biodegradable PCL composites exhibit decent mechanical strength(20.7 MPa)even at the MCC fraction of 65 wt%,which is superior to those(5-12.2 MPa)of the highly filled PCL composites(with filler contents of 50-63.8 wt%)reported so far.The proposed approach has sufficient expansibility for the fabrication of the highly filled polymer composites constructed by other types of matrix and fillers.

关键词： Polymer composites Microcrystalline cellulose Polycaprolactone Injection molding Dynamic reversible chemistry

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Masculinizer gene controls sexual differentiation in Hyphantria cunea

引用

Insect Science 2024年第2期31卷 405-416页

作者： Xiaowei Li Huihui Liu Honglun Bi Yaohui Wang Jun Xu Sufang zhang Zhen zhang ze zhang Yongping Huang Laboratory of Evolutionary and Functional Genomics School of Life SciencesChongqing UniversityChongqingChina CAS Key Laboratory of Insect Developmental and Evolutionary Biology CAS Centerfor Excellence in Molecular Plant SciencesInstitute of Plant Physiology and EcologyShanghaiChina Key Laboratory of Forest Protection Research Institute of Forest EcologyEnvironment and ProtectionChinese Academy of ForestryState Forestry AdministrationBeijingChina

The Masculinizer gene,Masc,encodes a lepidopteran-specific novel CCCHtype zinc finger protein,which controls sex determination and dosage compensation in Bombyx mori.Considering the potential application of it in pest control,it is necessary to investigate the function of Masc gene in Hyphantria cunea,a globally invasive forest pest.In the present study,we identified and functionally characterized the Masc gene,HcMasc,in H.cunea.Sequence analysis revealed that HcMASC contained the conserved CCCH-type zinc finger domain,nuclear localization signal,and male determining domain,in which the last was confirmed to be required for its masculinization in BmN cell line.However,expression data showed that unlike male-biased expression in B.mori,Hc-Masc gene expresses in main all developmental stages or tissues in both sexes.Clustered regularly interspaced palindromic repeats(CRISPR)/CRISPR-associated protein 9-based disruption of the common exons 1 and 3 of the HcMasc gene resulted in imbalanced sex ratio and abnormal external genitalia of both sexes.Our results suggest that the HcMasc gene is required for both male and female sexual differentiation and dosage compensation in H.cunea and provide a foundation for developing better strategies to control this pest.

关键词： CRISPR/Cas9 dosage compensation Hyphantria cunea Masc sexual differentiation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Fine Sand and Clay Sediment Acoustic Properties of the Novel Sediment Sample from the Arabian Sea:Experimental Investigations and Biot−Stoll Model Validation

引用

China Ocean Engineering 2024年第1期38卷 169-180页

作者： Shahabuddin SHAIKH HUANG Yi-wang zhang ze-chuan Habib Hussain ZUBERI National Key Laboratory of Underwater Acoustic Technology and College of Underwater Acoustic Engineering Harbin Engineering UniversityHarbin 150001China

The present study explores the physical and acoustic characteristics of fine sand and clay in novel seabed marine sediments from of Pakistan coastline of the Arabian Sea.The measured physical parameters included mean grain size,mass density,bulk density,salinity,porosity,permeability,pore size and mineralogical composition.Acoustic properties,including sound speed and attenuation,in the high frequency range of 90-170 kHz were analyzed.A controlled laboratory setup with the acoustic transmission method and Fourier transform techniques was utilized to examine the sound propagation and absorption of novel seabed sediments.The standard deviation of mean sound speed in fresh water was 0.75 m/s,and attenuation was observed in the range of 0.43 to 0.61 dB/m.The mean sound velocity in sand and clay varied from 1706 to 1709 m/s and 1602 to 1608 m/s,respectively.Corresponding average attenuation was observed at 80 to 93 dB/m in sandy sediments and from 31.8 to 38.6 dB/m in clayey sediments.Sound velocity variation within sandy sediment is low,consistent with expected results,and smaller than the predicted uncertainty.However,clay sediment exhibited a positive linear correlation and low sound speed variation.Attenuation increased linearly with frequency for both sediments.Finally,the laboratory results were validated by using the Biot−Stoll model.The dispersion of sound speed in sandy and clayey sediments was consistent with the predictions of the Biot−Stoll model.Measured attenuation aligned more with Biot−Stoll model predictions due to improved permeability,tortuosity and pore size parameter fitting.

关键词： physical and acoustic characteristics marine sediments sound speed attenuation Biot−Stoll model

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：