检索结果-南通市图书馆

Simulation of a DI Diesel Engine Performance Fuelled on Biodiesel Using a Semi-Empirical 0D Model

Energy and Power Engineering 2013年第10期5卷 596-603页

作者： Claude Valery Ngayihi Abbe robert nzengwa Raidandi Danwe Zacharie Merlin Ayissi Marcel Obounou Department of Physics Faculty of Sciences University of Yaoundé Yaoundé Cameroon Faculty of Industrial Engineering University of Douala Douala Cameroon Laboratory of Applied Mathematics National Advanced School of Engineering University of Yaoundé Yaoundé Cameroon Faculty of Industrial Engineering University of Douala Douala Cameroon

Diesel engines have proven over the years important in terms of efficiency and fuel consumption to power generation ratio. Many research works show the potential of biodiesel as a substitute for conventional gasoil. Mainly, previous and recent researches have focused on experimental investigation of diesel engine performance fuelled by biodiesel. Researches on the mathematical description of diesel engine process running on biodiesel are scarce, and mostly about chemical and thermodynamic description of the combustion process of biodiesel rather than performance studies. This work describes a numerical investigation on the performance analysis of a diesel engine fuelled by palm oil biodiesel. The numerical investigation was made using a semi empirical 0D model based on Wiebe’s and Watson’s model which was implemented via the open access numerical calculation software Scilab. The model was validated first by comparing with experimental pressure and performance data of a one cylinder engine at rated speed and secondly by comparing with a six cylinders engine performance data at various crankshaft rotational speeds. Simulations were then made to analyze the engine performance when running on biodiesel. The calculations were made at constant combustion duration and constant coefficient of excess air. Results showed that the model matches the overall experimental data, such as the power output and peak cylinder pressure. The ignition delay was somehow underestimated by the model for the first experiment, which caused a slight gap on in cylinder pressure curve, whereas it predicted the average ignition delay fairly well for the second set of validation. The simulations of engine performance when running on biodiesel confirmed results obtained in previous experimental researches on biodiesel. The model will be further investigated for engine control when shifting to biodiesel fuel.

关键词： Semi-Empirical 0D Model Scilab Biodiesel Performance Diesel Engine

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Prediction of Wearing of Cutting Tools Using Real Time Machining Parameters and Temperature Using Rayleigh-Ham Method

引用

Modern Mechanical Engineering 2023年第2期13卷 35-54页

作者： Jean Nyatte Nyatte Fabrice Alban Epee Wilba Christophe Kikmo Samuel Batambock Claude Valéry Ngayihi Abbe robert nzengwa E3M Laboratory National Higher Polytechnic School Douala University of Douala Douala Cameroon Institut Universitaire de Technologie (IUT-BOIS) University of Yaoundé I Mbalmayo Cameroon

Wear of cutting tools is a big concern for industrial manufacturers, because of their acquisition cost as well as the impact on the production lines when they are unavailable. Law of wear is very important in determining cutting tools lifespan, but most of the existing models don’t take into account the cutting temperature. In this work, the theoretical and experimental results of a dynamic study of metal machining against cutting temperature of a treated steel of grade S235JR with a high-speed steel tool are provided. This study is based on the analysis of two complementary approaches, an experimental approach with the measurement of the temperature and on the other hand, an approach using modeling. Based on unifactorial and multifactorial tests (speed of cut, feed, and depth of cut), this study allowed the highlighting of the influence of the cutting temperature on the machining time. To achieve this objective, two specific approaches have been selected. The first was to measure the temperature of the cutting tool and the second was to determine the wear law using Rayleigh-Ham dimensional analysis method. This study permitted the determination of a law that integrates the cutting temperature in the calculations of the lifespan of the tools during machining.

关键词： Machining Cutting Temperature Modeling Wear Cutting Tool

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：