检索结果-南通市图书馆

Acta Metallurgica Sinica(English Letters) 2022年第4期35卷 636-650页

作者： Zohreh Yazdani mohammad reza toroghinejad Hossein Edris Department of Materials Engineering Isfahan University of Technology84156-83111 IsfahanIran

The strengthening mechanisms of Al-TiAl_(3) nanocomposite, fabricated using cold roll bonding, annealing, and accumulative roll bonding(ARB) on Al sheets sandwiching with pure Ti powder were investigated in the present study. With annealing at 590 ℃ for 2 h, TiAl_(3) intermetallic compound was formed. After subsequent ARB process up to 5 cycles, final composite consists of ultrafine Al grains of less than 500 nm with TiAl_(3) particles larger than 200 nm. The strength and hardness of the final composite are 2.5 and 3.5 times the initial values, with an ultimate tensile strength of 400 MPa, which is dominated by grain-boundary strengthening due to the ultrafine Al grains, and Orowan strengthening due to the small TiAl_(3) particles. For comparison, an alternative fabrication route of cold roll bonding–ARB–annealing was also studied. This study showed that annealing before ARB is a critical factor in producing an ultrafine grain structure containing TiAl_(3) particles.

关键词： Composite Annealing Strength Microstructure Al

Effects of intermediate Ni layer on mechanical properties of Al–Cu layered composites fabricated through cold roll bonding

在线全文

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 2018年第5期25卷 573-583页

作者： Ali Shabani mohammad reza toroghinejad Alireza Bagheri Department of Materials Engineering Isfahan University of Technology

Layered composites have attracted considerable interest in the recent literature on metal composites. Their mechanical properties depend on the quality of the bonding provided by the intermediate layers. In this study, we analyzed the mechanical properties and bond strengths provided by the nickel layer with respect to its thickness and nature(either powder or coating). The results suggest that bond strength decreases with an increase in the content of nickel powder. At 0.3 vol% of nickel coating, we found the nature of nickel to be less efficient in terms of bond strength. A different picture arose when the content of nickel was increased and the bond strength increased in nickel coated samples. In addition, the results demonstrate that mechanical properties such as bend strength are strongly dependent on bond strength.

关键词： cold roll bonding Al/Ni/Cu composite mechanical testing metallography

Corrosion and wear resistance of coatings produced on AZ31 Mg alloy by plasma electrolytic oxidation in silicate-based K2TiF6 containing solution:Effect of waveform

在线全文

学校读者我要写书评

暂无评论

Journal of Magnesium and Alloys 2022年第9期10卷 2574-2587页

作者： Maryam Rahmati Keyvan Raeissi mohammad reza toroghinejad Amin Hakimizad Monica Santamaria Department of Materials Engineering Isfahan University of TechnologyIsfahan 84156-83111Iran Yekta Mobaddel Pars Co. Science and Technology CampusYazd UniversityYazd 89158-18411Iran Dipartimento di Ingegneria Università di PalermoViale Delle ScienzeEd.690128PalermoItaly

In this research,plasma electrolytic oxidation coatings were prepared on AZ31 Mg alloy in a silicate-based solution containing K_(2)TiF_(6) using bipolar and soft sparking waveforms with 10,20,and 30%cathodic duty *** coatings displayed a net-like surface morphology consisted of irregular micro-pores,micro-cracks,fused oxide particles,and a sintered *** to the incorporation of TiO_(2) colloidal particles and the cathodic pulse repair effect,most of the micro-pores were ***-term corrosion performance of the coatings was investigated using electrochemical impedance spectroscopy during immersion in 3.5 wt.%NaCl solution up to 14 *** coating grown by the soft sparking waveform with a 20%cathodic duty cycle having the lowest porosity(6.2%)and a sharp layer concentrated in F element at the substrate/coating interface shows the highest corrosion *** friction coefficient of this coating has remained stable during the sliding even under 5 N normal load,showing relatively higher wear resistance than other *** coating produced using the equivalent unipolar waveform,as the reference specimen,showed the highest friction coefficient and the lowest wear resistance despite its highest micro-hardness.

关键词： Plasma electrolytic oxidation Pulsed waveforms AZ31 Mg alloy Dipotassium titanium hexafluoride Corrosion resistance Wear resistance

Evaluation of microstructure and texture formation during annealing of cold-rolled FeCrCuMnNi multiphase high-entropy alloy

在线全文

学校读者我要写书评

暂无评论

Transactions of Nonferrous Metals Society of China 2020年第2期30卷 449-462页

作者： Ali SHABANI mohammad reza toroghinejad Department of Materials Engineering Isfahan University of Technology

Microstructure and texture variations of a cold-rolled multiphase FeCrCuMnNi high-entropy alloy were studied after different annealing *** were heat-treated at different temperatures and for different time,and then,subjected to different tests including XRD and *** results reveal that the FCC1 phase,which goes through more strain,has lower melting temperature,and recrystallizes earlier(lower temperature and shorter time).In addition,it is seen that particle stimulated nucleation is more effective on the recrystallization of this phase compared to FCC2 phase.A significant number of FCC1 nuclei form around the BCC *** of FCC2 phase initiated at 800℃mostly at the grain boundaries and the *** FCC1 phase was almost fully recrystallized at this *** annealing process led to the elimination of rolling textures,while the Brass component remained a major component in the recrystallized *** annealing temperature as well as annealing time led to the formation of Cube texture component,which is a major component of recrystallized low stacking fault energy ***,D and Rt-Co components formed during recrystallization as a result of the formation of annealing twins.

关键词： high-entropy alloys FeCrCuMnNi recrystallization microstructure texture

在线全文

学校读者我要写书评

暂无评论

镀层厚度对热浸镀锌低碳钢板可成行性的影响

现代冶金（内蒙古） 2009年第3期 56-64页

作者： mohammad reza toroghinejad[伊朗] 张怀军(译) 李德奎(校)

本文评价了热浸镀锌低碳钢板的可成行性，通过采用五种不同镀层重量的镀锌板，分析了镀层厚度对成行性的影响，并且与未采用镀层的镀锌板进行了比较。采用X-射线衍射和计算的织构参数确定镀层的定向结晶，通过采用成形极限图（FLD）对... 详细信息

本文评价了热浸镀锌低碳钢板的可成行性，通过采用五种不同镀层重量的镀锌板，分析了镀层厚度对成行性的影响，并且与未采用镀层的镀锌板进行了比较。采用X-射线衍射和计算的织构参数确定镀层的定向结晶，通过采用成形极限图（FLD）对试样进行单轴拉伸试验和对钢板成行性的评价，确定试样的机械性能。根据试验结果可以断定：通过提高镀层厚度，可以减少基面组元的织构参数，这种变化导致镀层薄板屈服强度的提高，但是降低了板材的延展性。对结果进行综合评价，涂层较厚的镀锌钢板成行性好于没有涂层镀锌钢板的成行性，同时也好于其它镀层较厚的钢板成行性。

关键词：热浸镀锌低碳钢结晶织构薄板成行性成形极限图