检索结果-南通市图书馆

Microstructure and Mechanical Behavior of Mg-Based Bimetal Plates with High Formability Sleeve by Co-extrusion

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Acta Metallurgica Sinica(English Letters) 2024年第3期37卷 499-512页

作者： Yue-Hui Dang Sheng-Lin Liu Xiao-Lei Ai Xiao-Wei Feng Bo Feng Zhuo Tian Ying-Fei Lin Huan-Tao Chen kai-hong zheng School of Materials Science and Engineering Chang’an UniversityShaanxi 710064China Guangdong Key Laboratory of Metal Toughening Technology and Application Institute of New MaterialsGuangdong Academy of SciencesGuangzhou 510650China

In this study,microstructure and mechanical behavior of two types of Mg-based bimetal plates with a high formability sleeve were systematically studied,with a great emphasis on the effect of the interface characteristic and the sleeve fraction on the plasticity of composite *** rule of mixtures(ROM)for elongation was also *** results show that when there is no or thin diffusion layer with thickness of about 3μm,Mg-based bimetal plates have a good plasticity with elongation of about 19-24%,and the ROM predicted elongations are very close to the experimental *** contrast,with a diffusion layer about 95-155μm thick,Mg-based bimetal plates exhibit a poor plasticity with elongation of about 11-17%,and the experimental elongations largely deviate from the ROM *** plasticity of Mg-based bimetal plates increases with increasing sleeve *** study provides new insights on the plastic deformation of Mg-based bimetal composites with a high formability sleeve.

关键词： Mg-based composites Co-extrusion Microstructure Mechanical behavior Plastic deformation

Al−Si−Fe−Mn合金熔体保温过程中富铁相的三维形态特征和生长行为

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Transactions of Nonferrous Metals Society of China 2024年第6期34卷 1745-1758页

作者：宋东福赵愈亮贾义旺李新涛周楠郑开宏张卫文广东省科学院新材料研究所广东省金属强韧化技术与应用重点实验室广州510650 华南理工大学金属材料近净成形国家工程技术研究中心广州510641 东莞理工大学机械工程学院东莞523808 贵州大学材料与冶金学院贵阳550025 江西寰球新材料科技有限公司上饶334499

采用扫描电子显微镜、透射电子显微镜、热力学计算和同步辐射X射线成像技术研究Al−7.0Si−1.0Fe−1.2Mn合金熔体保温过程中富铁相的形态演变和生长行为。结果表明,随着保温温度的降低,富铁相的形态由粗大的星形和多边形状转变成细小的汉... 详细信息

采用扫描电子显微镜、透射电子显微镜、热力学计算和同步辐射X射线成像技术研究Al−7.0Si−1.0Fe−1.2Mn合金熔体保温过程中富铁相的形态演变和生长行为。结果表明,随着保温温度的降低,富铁相的形态由粗大的星形和多边形状转变成细小的汉字状以及汉字和多边形的耦合结构。富铁相的三维形貌显示,星形富铁相由多个多分支的初生相和衍生的不规则次生相组成;耦合结构由多面体和枝晶组成;单一汉字相则由枝晶组成。随着保温温度的降低,富铁相的数量、体积分数以及最大富铁相的体积和连通性显著降低。原位同步辐射X射线结果显示,在凝固过程中形成了两类初生富铁相,其中尺寸较小的初生富铁相保留在熔体中,并成为耦合共晶结构富铁相的形核质点。

关键词：保温温度 Al−Si合金富铁相 3D形态演变同步辐射X射线

Corrosion and impact-abrasion-corrosion behaviors of quenching- tempering martensitic Fe-Cr alloy steels

在线全文

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2022年第11期29卷 1853-1863页

作者： Zhi-bin zheng Jun Long Yi Guo Hui Li kai-hong zheng Yan-xin Qiao Institute of New Materials Guangdong Academy of SciencesGuangdong Provincial Key Laboratory of Metal Toughening Technology and ApplicationGuangzhou 510650GuangdongChina Guangdong Provincial Iron Matrix Composite Engineering Research Center Guangzhou 510650GuangdongChina Jiangmen Guangjin Casting and Forging Co. Ltd.Jiangmen 529000GuangdongChina School of Materials Science and Engineering Jiangsu University of Science and TechnologyZhenjiang 212003JiangsuChina

The corrosion and impact-abrasion-corrosion behaviors of quenching-tempering Fe-Cr martensitic steels for ball mill liner were investigated in the corrosive slurry of a copper mine compared with high manganese *** is found that the corrosion resistance and the protectiveness of the passive film of Fe-Cr martensitic steels became worse when the carbon content *** quenching-tempering Fe-Cr martensitic steel showed better impact-abrasion-corrosion resistance in the corrosive slurry compared with the high manganese steel,especially the alloy steel with the carbon content of 0.3 wt.%.The synergistic effect between mechanics and corrosion has also been analyzed to further reveal the impact-abrasion-corrosion mechanism of the *** damage from pure mechanics accounted for the largest percentage(over 65%)for all steels,demonstrating that mechanical damage played the most important role in the impact-abrasion-corrosion behaviors of the *** impact and cracking resistance of the steel should also be paid special attention during the development of new materials for ball mill liner.

关键词： Mining Abrasive wear Corrosive wear Impact wear Martensitic steel

Effects of Ni content and tempering temperatures on microstructure and properties of medium-carbon cast steel

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2023年第8期30卷 1524-1536页

作者： Xiao-bo Cui Tian-long Liu Zhi-bin zheng Zhi-qiang Guo kai-hong zheng Pei-xian Han School of Materials Science and Engineering Shenyang University of TechnologyShenyang 110870LiaoningChina Institute of New Materials Guangdong Academy of SciencesNational Engineering Research Center of Powder Metallurgy of Titanium and Rare MetalsGuangdong Provincial Key Laboratory of Metal Toughening Technology and ApplicationGuangzhou 510651GuangdongChina Guangdong Provincial Iron Matrix Composite Engineering Research Center Guangzhou 510651GuangdongChina Jiangxi Lianfeng Investment Casting Co. Ltd.Yichun 336300JiangxiChina

The microstructure evolution and properties of medium-carbon cast steel alloyed with different Ni contents after tempering at various temperatures have been *** addition of 0.47-1.59 wt.%Ni content results in the formation of 16%-36% retained austenite(RA).The blocky and irregular-polygonal RA mainly forms along the prior austenite grain boundaries,and the tempering temperature does not affect the RA *** hardness of medium-carbon cast steel is affected by the precipitation of carbides and the hardness of *** RA content is the main cause of intergranular impact rupture and low impact *** long-strip carbides formed after tempering at 320℃ would further reduce the impact energy of medium-carbon cast *** tempering at 220 and 380℃,the increase in impact energy is attributed to the formation of rod-like and spherical carbides and the low-carbon *** the medium-carbon cast steel with high impact energy,its impact-abrasive wear resistance is more ***-cutting and delamination are the primary wear mechanisms.

关键词： Medium-carbon cast steel Ni content Tempering temperature Hardness Impact energy Impact-abrasive wear resistance

Revealing effect of aluminum alloying on work hardening and impact behaviors of low-density Fe-18Mn-1.3C-2Cr-(4,11)Al casting steel

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

China Foundry 2022年第4期19卷 359-368页

作者： Zhi-bin zheng Hao-kun Yang A.P.Shatrava Wai-wah Lai Jun Long kai-hong zheng Institute of New Materials Guangdong Academy of SciencesGuangdong Provincial Key Laboratory of Metal Toughening Technology and ApplicationGuangzhou 510650China Smart Manufacturing Division Hong Kong Productivity CouncilHong Kong 999077China Physicotechnological Institute of Metals and Alloys National Academy of SciencesKiev 03142Ukraine National Engineering Research Center of Powder Metallurgy of Titanium&Rare Metals Guangdong Provincial Iron Matrix Composite Engineering Research CenterGuangzhou 510650China

The present study designed two kinds of Fe-18Mn-1.3C-2Cr-(4,11)Al(wt.%)low-density *** and impact tests were carried out to evaluate the work hardening and impact toughness properties via aluminum(Al)alloying ***,microstructure evolution and fracture morphology were investigated by X-ray diffraction(XRD),a scanning electron microscope(SEM)equipped with electron backscatter diffraction(EBSD),a transmission electron microscope(TEM),and a stereo-optical microscope(OM).It is found that the Al addition obviously promotes the dislocation planar slipping,resulting in cleavage and brittle impact fracture in 11wt.%Al ***,the microband-induced plasticity(MBIP)mechanism is found in 4wt.%Al containing steel,introducing considerable work hardening capacity and impact toughness of 156.8±17.4 *** present study provides a direct illustration of the relationship between work hardening and impact toughness behaviors of these two low-density steels for potential application as impact-resistant components.

关键词： casting steel aluminum work hardening impact toughness tensile fractography impact fractography

Strengthening Mechanism and Microstructure of Deformable Ti Particles Reinforced AZ91 Composite

在线全文

学校读者我要写书评

暂无评论

Acta Metallurgica Sinica(English Letters) 2022年第12期35卷 1935-1945页

作者： Biao Tang Jian-Bo Li Jun-Liu Ye Huan Luo Yi-Tao Wang Bo Guan Yang-Fan Lu Xian-Hua Chen kai-hong zheng Fu-Sheng Pan School of Materials Science and Engineering Chongqing UniversityChongqing 400044China International Joint Laboratory for Light Alloys(MOE) School of Materials Science and EngineeringChongqing UniversityChongqing 400044China Institute of New Materials Guangdong Academy of SciencesGuangzhou 510650China

In this study,the deformable titanium(Ti)particles reinforced AZ91 composite was successfully prepared by powder metallurgy and subsequent *** mechanical properties and microstructural evolution of pure AZ91 and 5 Ti/AZ91 composite were *** yield strength,ultimate tensile strength,and elongation of 5 Ti/AZ91 composite are measured to be 212 MPa,323 MPa,and 10.1%,*** analysis revealed that Ti particles are elongated along the extrusion direction,forming a discontinuous strip Ti particles,fine precipitated Mg_(17)Al_(12) phase inhibits dynamic recrystallization(DRX)behavior through Zener pinning effect and hinders the growth of matrix grains,resulting in refiner grains of 5 Ti/AZ91 *** deformed Ti particles and magnesium(Mg)matrix to generate additional heterogeneous deformation-induced(HDI)*** deformation-induced strengthening mainly contributed to the increment of yield strength for 5 Ti/AZ91 composite.

关键词： Magnesium matrix composites Tiparticles Recrystallization Mechanical properties Heterogeneous deformation

Efficacy and Safety of Sanjie Analgesic Capsule in Patients with Endometriosis-Associated Pain:A Multicenter,3:1 Randomized,Double-Blind,Placebo-Controlled Trial

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Integrative Medicine 2024年第9期30卷 780-787页

作者： LENG Jin-hua DUAN Hua GUAN zheng ZHOU Ying-fang QU hong XU kai-hong ZHANG Shao-fen ZHANG Qin WANG Xin LIN kai-qing LANG Jing-he Department of Obstetrics and Gynecology Peking Union Medical College HospitalBeijing100730China Department of Gynecology Beijing Obstetrics and Gynecology HospitalCapital Medical UniversityBeijing100006China Department of Gynecology Chinese PLA General HospitalBeijing100039China Department of Gynecology Peking University First HospitalBeijing100034China Department of Gynecology Beijing Chao-yang HospitalBeijing100020China Department of Gynecology Womens Hospital School of Medicine Zhejiang UniversityHangzhouZhejiang Province310006China Department of Gynecology Obstetrics and Gynecology Hospital of Fudan UniversityShanghai200090China Department of Gynecology Hangzhou Hospital of Traditional Chinese MedicineHangzhou310007China Department of Gynecology Affiliated Hospital of Liaoning University of Traditional Chinese MedicineShenyang110032China

Objective:To assess the efficacy and safety of Sanjie Analgesic Capsule(SAC)in Chinese patients with endometriosis-associated ***:This was a multicenter,randomized,double-blind,placebo-controlled trial conducted at 15 centers between November 2013 and July 2017 in *** 323 patients with endometriosis were randomized at a 3:1 ratio to the SAC group(241 cases)and placebo group(82 cases)by stratified block *** in the SAC or placebo groups were given SAC or placebo 1.6 g 3 times per day,orally,respectively since the first day of menstruation for 3 consecutive menstrual *** primary endpoint was clinical response to dysmenorrhea evaluated using a 10-point Visual Analogue Scale at 3 and 6 *** secondary endpoint was the pain score evaluated by VAS(chronic pelvic pain,defecation pain,and dyspareunia)at 3 and 6 months,and the pain recurrence rate at 6 *** events(AEs)were recorded during the ***:A total of 241 women were included in the SAC group,and 82 were in the placebo *** these women,217(90.0%)and 71(86.6%)completed the intervention,*** 3 months,overall response rate(ORR)was significantly higher in women administered SAC(80.1%)compared with those who received a placebo(30.5%,P<0.01).Six months after treatment,the ORR for dysmenorrhea was 62.7%in the SAC group and 31.7%in the placebo group(P<0.01).Chronic pelvic pain and defecation pain were significantly improved by SAC compared with placebo(both P<0.05).The incidence rates of total AEs events in the SAC and placebo groups were 6.6%and 9.8%,respectively,and no significant difference was shown between the two groups(P=0.339).Conclusion:SAC is well-tolerated and may improve dysmenorrhea in women with endometriosis-associated pain.

关键词： endometriosis pain Sanjie Analgesic Capsule randomized controlled trial Chinese medicine

Exploring Trade-offs in Thermal Interface Materials:The Impact of Polymer-Filler Interfaces on Thermal Conductivity and Thixotropy

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Chinese Journal of Polymer Science 2024年第7期42卷 916-925,I0006页

作者： Bin Zhang zheng-Li Dou Yong-zheng Zhang Qiang Fu kai Wu College of Polymer Science and Engineering State Key Laboratory of Polymer Materials EngineeringSichuan UniversityChengdu610065China

Effective thermal transport across solid-solid interfaces which is essential in thermal interface materials(TIMs),necessitates both optimal thixotropy and high thermal *** role of filler surface modification,a fundamental aspect of TIM fabrication,in the influence of these properties is not fully *** study employs the use of a silane coupling agent(SCA)to modify alumina,integrating experimental approaches with molecular dynamics simulations,to elucidate the interface effects on thixotropy and thermal conductivity in polydimethylsiloxane(PDMS)-based *** findings reveal that the variations of SCAs modify both interface binding energy and transition layer *** interface binding energy restricts macromolecular segmental relaxation near the interface,hindering desirable thixotropy and bond line *** the contrary,the thickness of the transition layer at the interface positively influences thermal conductivity,facilitating the transport of phonons between the polymer and ***,selecting an optimal SCA allows a balance between traditionally conflicting goals of high thermal conductivity and minimal bond line thickness,achieving an impressively low interface thermal resistance of just 2.45-4.29 K·mm^(2)·W^(-1)at275.8 kPa.

关键词： Thermal interface material Surface modification Thermal conductivity Thixotropy Interface thermal resistance

Numerical manifold method for steady-state nonlinear heat conduction using Kirchhoff transformation

在线全文

学校读者我要写书评

暂无评论

Science China(Technological Sciences) 2024年第4期67卷 992-1006页

作者： ZHANG LiMei KONG Heng zheng hong Key Laboratory of Urban Security and Disaster Engineering Ministry of EducationBeijing University of TechnologyBeijing 100124China Beijing Municipal Construction Co. Ltd.Beijing 100048China

The numerical manifold method(NMM)introduces the mathematical and physical cover to solve both continuum and discontinuum problems in a unified *** this study,the NMM for solving steady-state nonlinear heat conduction problems is presented,and heat conduction problems consider both convection and radiation boundary ***,the nonlinear governing equation of thermal conductivity,which is dependent on temperature,is transformed into the Laplace equation by introducing the Kirchhoff *** transformation reserves linearity of both the Dirichlet and the Neumann boundary conditions,but the Robin and radiation boundary conditions remain ***,the NMM is employed to solve the Laplace equation using a simple iteration procedure because the nonlinearity focuses on parts of the problem domain ***,the temperature field is retrieved through the inverse Kirchhoff *** examples are analyzed,demonstrating the advantages of the Kirchhoff transformation over the direct solution of nonlinear equations using the NewtonRaphson *** study provides a new method for calculating nonlinear heat conduction.

关键词： numerical manifold method nonlinear heat conduction temperature-dependent thermal conductivity Kirchhoff transformation convection and radiation boundary conditions