检索结果-南通市图书馆

Finite element analysis and experimental validation of polymer-metal contacts in block-on-ring configuration

Friction 2024年第3期12卷 554-568页

作者： k.Y.Eayal AWWAD k.osro fallahnezhad B.F.YOUSIF Ahmad MOSTAFA Omar ALAJARMEH A.SHALWAN Xuesen ZENG Mechanical Engineering Department Faculty of EngineeringTafila Technical UniversityTafila 66110Jordan Medical Device Research Institute College of Science and EngineeringFlinders UniversitySouth Australia 5042Australia Centre for Future Materials University of Southern QueenslandToowoomba 4350Australia Department of Manufacturing Engineering Technology Public Authority for Applied Education and TrainingKuwait 13092Kuwait

The wear profile analysis,obtained by different tribometers,is essential to characterise the wear ***,most of the available methods did not take the stress distribution over the wear profile in consideration,which causes inaccurate *** this study,the wear profile of polymer–metal contact,obtained by block-on-ring configuration under dry sliding conditions,was analysed using finite element modelling(FEM)and experimental ***’s wear equation was integrated into a developed FORTRAN-UMESHMOTION code linked with Abaqus software.A varying wear coefficient(k)values covering both running-in and steady state regions,and a range of applied loads involving both mild and severe wear regions were measured and implemented in the *** FEM was in good agreement with the *** model reproduced the stress distribution profiles under variable testing conditions,while their values were affected by the sliding direction and maximum wear depth(hmax).The largest area of the wear profile,exposed to the average contact stresses,is defined as the normal *** the critical zones were characterized by high stress concentrations reaching up to 10 times of that at the normal *** wear profile was mapped to identify the critical zone where the stress concentration is the key point in this *** surface features were examined in different regions using scanning electron microscope(SEM).Ultimately,SEM analysis showed severer damage features in the critical zone than that in the normal zone as proven by ***,the literature data presented and considered the wear features the same at any point of the wear *** this study,the normal zone was determined at a stress value of about 0.5 MPa,whereas the critical zone was at about 5.5 *** wear behaviour of these two zones showed totally different features from one another.

关键词： polymer-to-metal contact block-on-ring wear profile wear model

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Influence of graphene nanoplatelets on mechanical properties and adhesive wear performance of epoxy-based composites

引用

Friction 2021年第4期9卷 856-875页

作者： k.Y.EAYAL AWWAD B.F.YOUSIF k.osro fallahnezhad khalid SALEH Xuesen ZENG Faculty of Health Engineering and SciencesUniversity of Southern QueenslandToowoombaQLDAustralia Centre for Future Materials University of Southern QueenslandToowoombaQLDAustralia School of Mechanical and Mining Engineering University of QueenslandBrisbaneQLDAustralia

Epoxy resin is one of the most widely used thermoset polymers in high-performance composite materials for lightweight ***,epoxy has a high coefficient of friction,which limits its tribological *** this study,the effect was investigated of different weight fractions of solid lubricant graphene nanoplatelets(GNPs),ranging from 0 to 4.5 wt%,on mechanical and adhesive wear performance of *** wear tests covered mild and severe wear *** correlation of tribological and mechanical properties was studied as *** electron microscopy(SEM)was used to observe the failure mechanisms for both tribological and mechanical samples after each *** results revealed that the addition of GNPs to the epoxy improved its stiffness and hardness but reduced its fracture strength and *** wear performance exhibited high efficiency with GNP additions and showed reductions in the specific wear rate,the coefficient of friction,and the induced interface temperature by 76%,37%,and 22%,respectively.A fatigue wear mechanism was predominant as the applied load *** importantly,severe wear signs occurred when the interface temperature reached the heat distortion temperature of the *** tribological,and mechanical properties showed only a weak correlation to each *** addition of GNPs to epoxy by less than 4.5 wt%was highly efficient to improve the wear performance while maintaining the fracture strength and *** transform infrared spectroscopy(FTIR)analysis shows no chemical interaction between the epoxy matrix with GNPs,which implies its physical interaction.

关键词： graphene nanoplatelets epoxy adhesive wear solid lubricants

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：