检索结果-南通市图书馆

Tuning mechanical and electrical performances of B_(4)C-TiB_(2)ceramics in a two-step spark plasma sintering process

引用

Journal of Advanced Ceramics 2024年第4期13卷 518-528页

作者： jun Zhao Xingshuo Zhang Zongning Ma Dong Wang Xing jin Songlin Ran Advanced Ceramics Research Center School of Materials Science and EngineeringAnhui University of TechnologyMaanshan 243002China Anhui Engineering Research Center for High Efficiency Intelligent Photovoltaic Module Chaohu UniversityHefei 238024China

B_(4)C–TiB_(2)is an advanced electrically conductive ceramic with excellent mechanical and electrical discharge machinable *** is challenging and rewarding to achieve highly conductive and hard B_(4)C–TiB_(2)composites at a minimum content of conductive TiB2 that has inferior hardness but double specific gravity of the B_(4)C matrix.A novel strategy was used to construct conductive networks in B_(4)C‒15 vol%TiB2 composite ceramics with B_(4)C,TiC,and amorphous B as raw materials by a two-step spark plasma sintering *** influences of particle size matching between B_(4)C and TiC on the conducting of the strategy and the microstructure were discussed based on the selective matrix grain growth *** mechanical and electrical properties were also systematically *** B_(4)C–15 vol%TiB2 composite ceramic prepared from 10.29µm B_(4)C and 0.05µm TiC powders exhibited a perfect three-dimensional interconnected conductive network with a maximum electrical conductivity of 4.25×10^(4)S/m,together with excellent mechanical properties including flexural strength,Vickers hardness,and fracture toughness of 691±58 MPa,30.30±0.61 GPa,and 5.75±0.32 MPa·m^(1/2),respectively,while the composite obtained from 3.12µm B_(4)C and 0.8µm TiC powders had the best mechanical properties including flexural strength,Vickers hardness,and fracture toughness of 827±35 MPa,32.01±0.51 GPa,and 6.45±0.22 MPa·m^(1/2),together with a decent electrical conductivity of 0.65×10^(4)S/m.

关键词： B_(4)C-TiB_(2) mechanical properties electrical conductivity conductive network

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Laser-Constructing 3D Copper Current Collector with Crystalline Orientation Selectivity for Stable Lithium Metal Batteries

引用

ENERGY & ENVIRONMENTAL MATERIALS 2024年第6期7卷 129-139页

作者： Li, Hui Wang, Gang Hu, jin Li, jun Huang, Jiaxu Xu, Shaolin Southern Univ Sci & Technol Dept Mech & Energy Engn Shenzhen 518000 Peoples R China

The practical application of lithium (Li) metal anodes in high-capacity batteries is impeded by the formation of hazardous Li dendrites. To address this challenge, this research presents a novel methodology that combines laser ablation and heat treatment to precisely induce controlled grain growth within laser-structured grooves on copper (Cu) current collectors. Specifically, this approach enhances the prevalence of Cu (100) facets within the grooves, effectively lowering the overpotential for Li nucleation and promoting preferential Li deposition. Unlike approaches that modify the entire surface of collectors, our work focuses on selectively enhancing lithiophilicity within the grooves to mitigate the formation of Li dendrites and exhibit exceptional performance metrics. The half-cell with these collectors maintains a remarkable Coulombic efficiency of 97.42% over 350 cycles at 1 mA cm(-2). The symmetric cell can cycle stably for 1600 h at 0.5 mA cm(-2). Furthermore, when integrated with LiFePO4 cathodes, the full-cell configuration demonstrates outstanding capacity retention of 92.39% after 400 cycles at a 1C discharge rate. This study introduces a novel technique for fabricating selective lithiophilic three-dimensional (3D) Cu current collectors, thereby enhancing the performance of Li metal batteries. The insights gained from this approach hold promise for enhancing the performance of all laser-processed 3D Cu current collectors by enabling precise lithiophilic modifications within complex structures.

关键词： copper current collector heat treatment laser processing lithium metal battery selective crystalline orientation ABNORMAL GRAIN-GROWTH LI METAL DEPOSITION TEXTURE ENERGY

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Dynamic lithium-compensation mechanism for densification of garnet-type Li_(7)La_(3)Zr_(2)O_(12)electrolyte by Li_(2)O atmosphere buffer pair

引用

Nano Research 2024年第7期17卷 6184-6191页

作者： Chujun Zheng Ya Chen Haoxin Dong Yan Lu jun jin Zhaoyin Wen CAS Key Laboratory of Materials for Energy Conversion Shanghai Institute of CeramicsChinese Academy of ScienceShanghai 200050China State Key Lab High Performance Ceram and Superfine Shanghai Institute of CeramicsChinese Academy of SciencesShanghai 200050China Center of Materials Science and Optoelectronics Engineering University of Chinese Academy of SciencesBeijing 100049China

Solid-state lithium metal batteries are one of the most promising options for next-generation batteries pursuing high-energy density and ***,the inevitable volatilization of lithium compounds during sintering leads to low relative density and low ionic conductivity of solid-state ***,the dynamic lithium-compensation mechanism is proposed to facilitate the densification of Ta-substituted garnet-type electrolyte(Li_(6.5)La_(3)Zr_(1.5)Ta_(0.5)O_(12)(LLZT))through the reversible manipulating of Li_(2)O ***_(2)ZrO_(3)is used as mother powder additive,which reacts with Li_(2)O in sintering atmosphere and forms Li_(6)Zr_(2)O_(7).Li_(2)ZrO_(3)/Li_(6)Zr_(2)O_(7)buffer pair manipulates the sintering Li_(2)O atmosphere,which is vital for LLZT,within the Li_(2)O partial pressure range corresponding to Li_(2)ZrO_(3)and Li_(6)Zr_(2)O_(7).Furthermore,the reversibility mechanism of buffer pair for Li_(2)O absorption and release is *** obtained LLZT exhibits a relative density of over 96%and an ionic conductivity exceeding 7×10^(−4)S·cm^(−1)with no abnormal grain *** symmetric cell demonstrates an excellent lithium dendrite suppressing ability(stable cycling at a current density of 0.3 mA·cm^(−2)for over 1000 h).Such dynamic lithium-compensation strategy has been successfully applied in atmosphere manipulation of LLZT sintering process,which reduces the dependence of LLZT on the Li_(2)O atmosphere,making it conducive to large-scale preparation of electrolyte ceramics.

关键词： solid-state batteries garnet-type electrolyte high-density electrolyte dynamic lithium-compensation buffer pair

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Insights into postural orthostatic tachycardia syndrome after COVID-19 in pediatric patients

引用

World Journal of Pediatrics 2024年第3期20卷 201-207页

作者： Ya-Xi Cui jun-Bao Du Hong-Fang jin Department of Pediatrics Peking University First HospitalNo.1 Xi-an Men StreetWest DistrictBeijing 100034China State Key Laboratory of Vascular Homeostasis and Remodeling Peking UniversityBeijing 100191China

The pandemic caused by the novel severe acute respiratory syndrome coronavirus 2(SARS-CoV-2)profoundly threatened human health globally and greatly impacted the world economy[1].While most patients recovered,some suff... 详细信息

关键词： acute patients tachycardia

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

A single center investigation of bare-metal or drug-eluting stent restenosis from 1633 consecutive Chinese Han ethnic patients

引用

Chinese Medical Journal 2006年第7期119卷 533-538页

作者： XU Bo LI jian-jun YANG Yue-jin MA Wei-hua CHEN Ji-lin QIAO Shu-bin QIN Xue-wen YAO Min LIU Hai-bo WU Yong-jian YUAN jin-qing CHEN Jue YOU Shi-jie DAI jun XIA Ran GAO Run-lin Department of Cardiology Fuwai Hospital Chinese Academy ofMedical Sciences Peking Union Medical College Beijing 100037China

Background Stents are widely used in China but the clinical impression is somehow that restenosis is less common because of the lower prevalence of coronary artery disease （CAD） and associated risk factors in Chinese populations. However, no large-sample published studies are available on angiographic stent restenosis including those of bare-metal stent （BMS） or drug-eluting stent （DES） in Chinese Han ethnic population. Mothods A total of 1633 consecutive patients with CAD who had undergone coronary stenting, quantitative coronary angiography （QCA） were retrospectively studied. At the time of stent implantation and at 7 months post-stenting 675 patients had a follow-up angiography. Statistical analysis was made with the chi-square test for categorical variables, unpaired t test for continuous variables, univariate or multivariate regression for baseline and angiographic characteristics and the Kaplan-Meier method for rate of target lesion revascularization （TLR）. Results Stent restenosis was defined as ≥50% diameter stenosis in the dilated segment. A total of 675 patients with 1074 lesions were subjected to angiographic follow-up for 7 months on average, Of these lesions, 448 were implanted with BMS whereas 626 lesions with DES. At 7 months, bare-metal in-stent restenosis occured in 148 lesions （33.0%）, and bare metal in-segment restenosis in 155 lesions （34.6%） in contrast to drug-eluting in-stent restenosis in 48 lesions （7.7%） and drug-eluting in-segment restenosis in 73 lesions （11.7%）（P〈0.001 compared with BMS respectively）. Late loss in both in-stent and in segment was higher in BMS than in DES groups [（1.00±0.69） vs （0.28±0.52）; （0.78±0.71） vs （0.21±0.52）, P〈0.001 respectively]. Angulated lesion, lesion length, pre-procedural minimal luminal diameter （MLD）, and BMS were independent predictors for TLR, （P〈0.01 respectively）, whereas current smoker, ostial lesion, and stent overlapping, post-procedure in-stent MLD, lesion length, and stent types were indep

关键词： stent coronary artery disease angiography restenosis

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Research on the solid particle erosion wear of pipe steel for hydraulic fracturing based on experiments and numerical simulations

引用

Petroleum Science 2024年第4期21卷 2779-2792页

作者： Si-Qi Yang jian-Chun Fan Ming-Tao Liu De-Ning Li jun-Liang Li Li-Hong Han jian-jun Wang Shang-Yu Yang Si-Wei Dai Lai-Bin Zhang State Key Laboratory of Oil and Gas Equipment CNPC Tubular Goods Research Institute Key Laboratory of Oil and Gas Safety and Emergency Technology China University of Petroleum Oil Production Technology Research Institute of Liaohe Oilfield Company Tianjin Gas Storage Branch PetroChina Dagang Oilfield Company Petroleum Production Engineering Research Institute Daqing Oilfield Company

Erosion wear is a common failure mode in the oil and gas industry. In the hydraulic fracturing, the fracturing pipes are not only in high-pressure working environment, but also suffer from the impact of the high-speed solid particles in the fracturing fluid. Beneath such complex conditions, the vulnerable components of the pipe system are prone to perforation or even burst accidents, which has become one of the most serious risks at the fracturing site. Unfortunately, it is not yet fully understood the erosion mechanism of pipe steel for hydraulic fracturing. Therefore, this article provides a detailed analysis of the erosion behavior of fracturing pipes under complex working conditions based on experiments and numerical simulations. Firstly, we conducted erosion experiments on AISI 4135 steel for fracturing pipes to investigate the erosion characteristics of the material. The effects of impact angle, flow velocity and applied stress on erosion wear were comprehensively considered. Then a particle impact dynamic model of erosion wear was developed based on the experimental parameters, and the evolution process of particle erosion under different impact angles, impact velocities and applied stress was analyzed. By combining the erosion characteristics, the micro-structure of the eroded area, and the micro-mechanics of erosion damage, the erosion mechanism of pipe steel under fracturing conditions was studied in detail for the first time. Under high-pressure operating conditions, it was demonstrated through experiments and numerical simulations that the size of the micro-defects in the eroded area increased as the applied stress increased, resulting in more severe erosion wear of fracturing pipes.

关键词： Erosion wear Applied stress Particle impact dynamics Erosion mechanism

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Enhanced plasticity of spontaneous coagulation cast oxide ceramic green bodies

引用

Journal of Advanced Ceramics 2024年第5期13卷 568-578页

作者： Juanjuan Wang jin Zhao junyan Mao Wenlong Liu Haohao Ji jian Zhang Shiwei Wang State Key Laboratory of High Performance Ceramics and Superfine Microstructure Shanghai Institute of CeramicsChinese Academy of SciencesShanghai 200050China Center of Materials Science and Optoelectronics Engineering University of Chinese Academy of SciencesBeijing 100049China

In the preparation of large-sized ceramics,the use of a green body with relatively high plasticity is crucial to minimize the risk of cracking during *** achieve this goal,glycerol and polyethylene glycol(PEG)were utilized as plasticizers in the shaping of green bodies of oxide ceramics through spontaneous coagulation casting(SCC).This study investigated the effects of plasticizers and particle sizes ranging from the submicron to nanoscale on the slurry viscosity,drying shrinkage of wet gels,and mechanical properties of green *** plasticity of the green bodies was assessed by measuring the impact toughness and flexural stress‒strain *** incorporating an appropriate plasticizer,the peak width of the flexural stress‒strain curve for dried green bodies from particles of different sizes was nearly twice that without plasticizers,and the impact toughness was enhanced by approximately 71%,34%,and 41%when the particle size decreased from the submicron scale to the nanoscale(0.45μm,0.18μm,and 50 nm,respectively).The drilling test revealed that there was nearly no cracking around the holes in the green bodies with *** plasticity mechanism of the green bodies was examined based on ultraviolet–visible(UV–Vis)spectroscopy and scanning electron microscopy(SEM).It was discovered that plasticizers might mitigate the brittleness of green bodies by adjusting the interactions between molecules and modifying the gel network properly.

关键词： green body plasticity plasticizer particle size impact toughness stress-strain curve

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

A polymyxin B loaded hypoxia-responsive liposome with improved biosafety for efficient eradication of bacterial biofilms

引用

Nano Research 2024年第9期17卷 8325-8336页

作者： Fang Liu Lingyun Zou Yongcheng Chen Zuolong Liu Yue Huang Qiao jin jian Ji MOE Key Laboratory of Macromolecule Synthesis and Functionalization of Ministry of Education Department of Polymer Science and EngineeringZhejiang UniversityHangzhou 310027China State Key Laboratory of Transvascular Implantation Devices The Second Affiliated Hospital Zhejiang University School of MedicineHangzhou 310009China

Biofilm-associated bacterial infection brings serious threats to global public health owing to serious antibiotic *** is urgently needed to develop innovative strategies to combat biofilm-associated bacterial *** stand out as the last line of defense against Gram-negative ***,serious nephrotoxicity of polymyxins severely limits their clinical ***,a hypoxia-responsive liposome is designed as the nanocarrier of polymyxin B(PMB)to combat biofilms developed by Gram-negative bacteria.A metronidazole modified lipid(hypoxia-responsive lipid(HRLipid))is synthesized to fabricate hypoxia-responsive liposomes(HRLip).PMB loaded hypoxia-responsive liposomes(HRL-PMB)is then prepared to mitigate the nephrotoxicity of PMB while preserving its excellent bactericidal ***-PMB shows very low hemolysis and cytotoxicity due to liposomal encapsulation of *** can be readily released from HRL-PMB in response to hypoxic biofilm microenvironment,exerting its bactericidal activity to realize biofilm *** excellent in vivo antibiofilm ability of HRL-PMB is confirmed by a Pseudomonas aeruginosa infected zebrafish model and a *** pneumonia infection ***,HRL-PMB can greatly reduce the nephrotoxicity of PMB after intravenous *** hypoxia-sensitive liposomes held great promise to improve the biosafety of highly toxic antibiotics while preserving their intrinsic bactericidal ability,which may provide an innovative strategy for combating biofilm-associated infections.

关键词： bacterial biofilm hypoxia liposome polymyxin B nephrotoxicity

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

BaCe_(0.8)Fe_(0.1)Ni_(0.1)O_(3−δ)-impregnated Ni-GDC by phase-inversion as an anode of solid oxide fuel cells with on-cell dry methane reforming

引用

Journal of Advanced Ceramics 2024年第6期13卷 834-841页

作者： Yanya Liu jun Luo Cheng Li Bo Liu Dong Yan jian Li Lichao Jia School of Materials Science and Engineering State Key Laboratory of Materials Processing and Die&Mould TechnologyHuazhong University of Science and TechnologyWuhan 430074China

BaCe_(0.8)Fe_(0.1)Ni_(0.1)O_(3−δ)(BCFN)in a perovskite structure is impregnated consecutively by BCFN solution and BCFN suspension into a phase-inversion prepared NiO–Gd_(0.1)Ce_(0.9)O_(2−δ)(GDC)scaffold as an anode for solid oxide fuel cells(SOFCs)with on-cell dry reforming of methane(DRM).The whole pore surface of the scaffold is covered by small BCFN particles formed by BCFN solution impregnation;the large pores near the scaffold surface are filled by BCFN aerogels with a high specific surface area produced by BCFN suspension impregnation,which act as a catalytic layer for on-cell *** reduction,the anode consists of a Ni–GDC scaffold and BCFN particles with exsolved FeNi3 *** BCFN-impregnated Ni–GDC anode has higher electrical conductivity,electrochemical activity,and resistance to carbon deposition,with which the cell shows maximum power densities between 1.44 and 0.92 W·cm^(−2) when using H_(2) and between 1.09 and 0.50 W·cm^(−2) when using CO_(2)–CH_(4) at temperatures ranging from 750 to 600℃.A stable performance at 400 mA·cm^(−2) and 700℃is achieved using 45%CO_(2)–45%CH_(4)–10%N_(2) for more than 400 h without carbon deposition,benefiting from the impregnated BCFN aerogel with a high specific surface area and water adsorbability.

关键词： aerogel solid oxide fuel cells(SOFCs) phase-inversion dry reforming of methane(DRM) carbon resistance

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Do brood parasitic Common Cuckoos develop brood patches during the breeding season?

引用

Avian Research 2024年第3期15卷 363-368页

作者： jun-Seo Go Hae-Ni Kim Sue-Jeong jin Myeong-Chan Cha Heesoo Lee jin-Won Lee Korea Institute of Ornithology&Department of Biology Kyung Hee University02447SeoulRepublic of Korea Bird Research SaeZiP 12504YangpyeongRepublic of Korea

Many birds develop brood patches on their ventral apterium under hormonal regulation to effectively transmit body heat to eggs during *** developed patch has several characteristics,including de-feathering,vascularization,and ***,little is known about whether avian brood parasites that do not incubate their eggs exhibit brood patch development during the breeding *** this study,we measured the size of the ventral apterium in 114 Common Cuckoos(Cuculus canorus)captured in the field throughout the breeding season and examined the appearance of the ventral apterium to confirm the development of brood *** also examined whether morphological traits and various factors correlated with the size of the ventral apterium(sternal apterium and abdominal apterium)and how it changed during the breeding *** found no clear signs of brood patch development in Common Cuckoos captured throughout the breeding season,indicating that they likely did not develop brood patches on the ventral apterium during this *** also found that ventral apterium size was positively correlated with wing length and body *** addition,Common Cuckoos with newly growing feathers on the boundary of the ventral apterium with pteryla were frequently observed as seasons progressed to the *** conclusion,Common Cuckoos exhibit neither brood patch development nor the vestigial characteristics of ancestral brood patches,except for the growth of feathers on boundary the ventral *** studies examining brood patches across different groups of avian brood parasites are valuable for enhancing our understanding of the developmental and physiological adaptations of avian brood parasites.

关键词： Brood parasitism Brood patch Common Cuckoo Pterylosis Re-feathering Ventral apterium

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：