检索结果-南通市图书馆

Effect of slag composition on kinetic behavior of deep deoxidation of 5 wt.% Si high-silicon austenitic stainless steel

引用

Journal of Iron and Steel Research International 2024年第8期31卷 1873-1885页

作者： Guan-xiong Dou han-jie Guo jing Guo Xue-cheng Peng Qing-yun Chen School of Metallurgical and Ecological Engineering University of Science and Technology Beijing(USTB)Beijing 100083China Beijing Key Laboratory of Special Melting and Preparation of High-End Metal Materials Beijing 100083China

Based on a thermodynamic study of 5 wt.%Si high-silicon austenitic stainless steel(SS-5Si)smelting using CaF_(2)-CaO-Al_(2)0_(3)-Mg-Si0_(2) slag to obtain a low oxygen content of less than 10×10^(-4) wt.%,a kinetic mass transfer model for deep deoxidation was established through laboratory studies,and the effects of slag components and temperature on deoxidation during the slag-steel reaction process of sS-5Si were systematically *** experimental data verified the accuracy of the model *** results showed that the final oxygen content in the steel at 1873 K was mainly controlled by the oxygen content derived from the activity of SiO_(2) regulated by the[Si]-[O]equilibrium reaction in the slag system;in particular,when the slag basicity R(R=w(CaO)/w(SiO2),where w(CaO)and w(SiO_(2))are the contents of CaO and SiO_(2) in the slag,respectively)is 3,the Al2O3 content in the slag needs to be less than 2.7%.The mass transfer rate equation for the kinetics of the deoxidation reaction revealed that the mass transfer of oxygen in the liquid metal is the rate-controlling step under different slag conditions at 1873 K,and the oxygen transfer coefficient ko.m increases with increasing the slag basicity from 4.0×10^(-6)m s^(-1)(R=1)to 4.3×10^(-5) m s^(-1)(R=3).ko.m values at R=2 and R=3 are almost the same,indicating that high slag basicity has little *** integral of the mass transfer rate equation for the deoxidation reaction of SS-5Si under different slag conditions is *** total oxygen content of the molten steel decreases with increasing basicity from an initial content of 22×10^(-4) to 3.2×10^(-4) wt.%(R=3),consistent with the change in ko.m with slag *** R=2,the slag-steel reaction takes 15 min to reach equilibrium(w[O]=5.5×10^(-4) wt.%),whereas at R=3,the slag-steel reaction takes 30 min to reach equilibrium(w[0]=3.2×10^(-4) wt.%).Considering the depth of deoxidation and reaction time of SS-5Si smelting,it is recommended the slag b

关键词： Slag-steel reaction Kinetics Rate-controlling step Deep deoxidation Transfer coefficient

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Interface optimization of graphene paper-Cu composite prepared by electrodeposition

引用

Journal of Iron and Steel Research International 2024年第1期31卷 64-73页

作者： jing Guo Hai-jing Wang Shuang-juan Liu Peng Zhang jing-yu Tang Wei-yang Zhang han-jie Guo Peng-cheng Wang Cai Meng School of Metallurgical and Ecological Engineering University of Science and Technology BeijingBeijing100083China Institute of High Energy Physics Chinese Academy of SciencesBeijing100049China Advanced Technology and Materials Co. Ltd.Beijing100083China School of Nuclear Science and Technology University of Science and Technology of ChinaHefei230027AnhuiChina

A room-temperature electrodeposition method with an organic electrolyte was developed to fabricate a HNO3-pretreated graphene paper Cu(GP'-Cu)*** improve the interfacial bonding of GP'-Cu composite,magnetron sputtering technology was used to create a"sandwich"structural gradient GP'-Cu *** selection of the intermediate transition layer metal was based on two-dimensional *** electron microscopy,X-ray photoelectron spectroscopy,and other analytical methods confirmed that the addition of an intermediate transition metal(Cr,Ni)layer reduced the gap distance and enhanced the interfacial bonding of the GP'and Cu deposited *** GP'-Ni-Cu composite exhibited the largest increase in tensile strength and *** addition,it had the highest thermal diffusivity and elongation at break among the GP'-Cu,GP'-Cr-Cu and GP'-Ni-Cu composites.

关键词： Graphene paper Two-dimensional disregistry Magnetron sputtering Metal composite

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Theoretical insights into efficient oxygen evolution reaction using non-noble metal single-atom catalysts on W2CO2 MXene

引用

Rare Metals 2024年第10期43卷 5082-5094页

作者： jing-Yu Zhou Zhi-cheng han Shu Zhao Tao Yang Da-Zhou Yan Hai-Jun Yu Institute of Advanced Battery Materials and Devices College of Materials Science and EngineeringBeijing University of Technology Key Laboratory of Advanced Functional Materials Ministry of EducationBeijing University of Technology China ENFI Engineering Corporation National Engineering Research Center of Silicon-Based Materials Manufacturing Technology

The pursuit of highly active oxygen evolution reaction （OER） catalysts,especially those free of noble metals,is a focal point in fuel cell *** extensive density functional theory calculations,this study designed and evaluated the activity and stability of singleatom catalysts （SACs） composed of 3d,4d and 5d transition metals supported on tungsten-based MXene for OER *** highlighted the exceptional OER performance of Ni@W2CO2,Rh@W2CO2and Pt@W2CO2,displaying remarkably low overpotentials The catalytic activity of TM@W2CO2SACs exhibited a robust correlation with surface properties,particularly the d-band center index and surface work *** Ni@W2CO2,Rh@W2CO2and Pt@W2CO2emerged as promising candidates for OER and oxygen reduction reaction （ORR） bifunctional catalysis,while Pt@W2CO2and Rh@ W2CO2showed high potential for OER and hydrogen evolution reaction （HER） bifunctional catalysis The effectiveness of tungsten-based MXene as a substrate for non-noble-metal SACs marks a breakthrough in OER catalyst design,driving advancements towards sustainable energy solutions and addressing critical challenges in energy conversion and storage.

关键词： Density functional theory MXene Non-noble metal Oxygen evolution reaction Single-atom catalysts

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Relationship Between Microbial Community and Soil Properties During Natural Succession of Abandoned Agricultural Land

引用

Pedosphere 2010年第3期20卷 352-360页

作者： JIA Guo-Mei ZhanG Pei-Dong WANG Gang CAO jing han jing-cheng HUANG Ying-Ping College of Chemistry and Life Science China Three Gorges Unversity Yichang 443002 (China) Key Laboratory of Arid and Grassland Ecology School of Life Science Lanzhou University Lanzhou 730000 (China) Qingdao Institute of Bioenergy and Bioprocess Technology Chinese Academy of Sciences Qingdao 266071 (China)

The changes of microbial biomass carbon (MBC) and nitrogen (MBN) and microbial community in the topsoil of the abandoned agricultural land on the semi-arid Loess Plateau in China during the natural succession were evaluated to understand the relationship between microbial community and soil properties. MBC and MBN were measured using fumigation extraction, and microbial community was analyzed by the method of fatty acid methyl ester (FAME). The contents of organic C, total N, MBC, MBN, total FAME, fungal FAME, bacterial FAME and Gram-negative bacterial FAME at the natural succession sites were higher than those of the agricultural land, but lower than those of the natural vegetation sites. The MBC, MBN and total FAME were closely correlated with organic C and total N. Furthermore, organic C and total N were found to be positively correlated with fungal FAME, bacterial FAME, fungal/bacterial and Gram-negative bacterial FAME. Natural succession would be useful for improving soil microbial properties and might be an important alternative for sustaining soil quality on the semi-arid Loess Plateau in China.

关键词： fatty acid methyl ester microbial biomass soil carbon soil nitrogen

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Mechanical and damping performances of TPMS lattice metamaterials fabricated by laser powder bed fusion

引用

China Foundry 2024年第4期21卷 327-333页

作者： Yan-peng Wei Huai-qian Li jing-jing han Ying-chun Ma Hao-ran Zhou jing-chang cheng Jian Shi Zhi-quan Miao Bo Yu Feng Lin National Key Laboratory of Advanced Casting Technologies Shenyang Research Institute of Foundry Co.Ltd.CAMShenyang 110022China Department of Mechanical Engineering Tsinghua UniversityBeijing 100084China Key Laboratory of Space Physics Beijing 100076China

Lattice metamaterials based on three-period minimum surface(TPMS)are an effective means to achieve lightweight and high-strength materials which are widely used in various fields such as aerospace and ***,its vibration and noise reduction,and damping properties have not been fully ***,in this study,the TPMS structures with parameterization were designed by the method of surface migration,and the TPMS structures with high forming quality was manufactured by laser powder bed fusion(LPBF).The mechanical properties and energy absorption characteristics of the beam and TPMS structures were studied and compared by quasi-static *** modal shapes of the beam lattice structures and TPMS structures were obtained by the free modal analysis,and the damping properties of two structures were obtained by modal *** the two structures after heat treatment with the same porosity of 70%,the yield strength of the beam lattice structure reaches 40.76 MPa,elastic modulus is 20.38 GPa,the energy absorption value is 32.23 MJ·m^(-3),the damping ratio is 0.52%.The yield strength,elastic modulus,energy absorption value,and damping ratio of the TPMS structure are 50.74 MPa,25.37 GPa,47.34 MJ·m^(-3),and 0.99%,*** results show that TPMS structures exhibit more excellent mechanical properties and energy absorption,better damping performance,and obvious advantages in structural load and vibration and noise reduction compared with the beam lattice structures under the same porosity.

关键词： lattice metamaterials TPMS energy absorption damping laser powder bed fusion

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Thermodynamic and experimental study of high-temperature roasting of blast furnace gas ash for recovery of metallic zinc and iron

引用

Journal of Iron and Steel Research International 2024年第1期31卷 108-120页

作者： Zi-han Wang jing Guo han-jie Guo Bin Li School of Metallurgical Engineering University of Science and Technology BeijingBeijing100083China School of Metallurgical Engineering Xi’an University of Architecture and TechnologyXi’an710055ShaanxiChina

A high-temperature reduction roasting method was used to achieve metallic iron and zinc recovery from blast furnace gas ash(BFA).The reduction processes for Zn-containing and Fe-containing oxides were analyzed in detail by using ther-modynamic equilibrium calculation and the principle of minimum free *** results showed that the main reaction in the system is the reduction of ZnFe_(2)_(4)and iron *** the full temperature range,iron oxides were more easily reduced than zinc *** of the amount of CO contained in the system,the reduction of ZnO to Zn was difficult to proceed below the boiling point(906℃)of *** the reduction temperature is below 906℃,the reduction process of zinc ferrate was ZnFe_(2)_(4)→ZnO;when the reduction temperature is above 906℃,its reduction process becomed ZnFe_(2)_(4)→ZnO→Zn(g).The metallization and dezincification rates of the BFA gradually increased with increasing reaction *** the C/O ratio increased,the metallization and dezincification rates first increased and then *** effect of reduction time on BFA reduction was similar to that of reaction temperature.

关键词： Blast furnace gas ash Thermodynamics Zinc removal Iron reduction High-temperature reduction roasting Integrated utilization

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Prediction and Output Estimation of Pattern Moving in Non-Newtonian Mechanical Systems Based on Probability Density Evolution

引用

Computer Modeling in Engineering & Sciences 2024年第4期139卷 515-536页

作者： cheng han Zhengguang Xu School of Automation and Electrical Engineering University of Science and Technology BeijingBeijing100083China Key Laboratory of Knowledge Automation for Industrial Processes University of Science and Technology BeijingBeijing100083China

A prediction framework based on the evolution of pattern motion probability density is proposed for the output prediction and estimation problem of non-Newtonian mechanical systems,assuming that the system satisfies the generalized Lipschitz *** a complex nonlinear system primarily governed by statistical laws rather than Newtonian mechanics,the output of non-Newtonian mechanics systems is difficult to describe through deterministic variables such as state variables,which poses difficulties in predicting and estimating the system’s *** this article,the temporal variation of the system is described by constructing pattern category variables,which are non-deterministic *** pattern category variables have statistical attributes but not operational attributes,operational attributes are assigned to them by posterior probability density,and a method for analyzing their motion laws using probability density evolution is ***,a data-driven form of pattern motion probabilistic density evolution prediction method is designed by combining pseudo partial derivative(PPD),achieving prediction of the probability density satisfying the system’s output *** on this,the final prediction estimation of the system’s output value is realized by minimum variance unbiased ***,a corresponding PPD estimation algorithm is designed using an extended state observer(ESO)to estimate the parameters to be estimated in the proposed prediction *** effectiveness of the parameter estimation algorithm and prediction method is demonstrated through theoretical analysis,and the accuracy of the algorithm is verified by two numerical simulation examples.

关键词： Non-newtonian mechanical systems prediction and estimation pattern moving probability density evolution pseudo partial derivative

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

A Simple Proof of ACC for Minimal Log Discrepancies for Surfaces

引用

Acta Mathematica Sinica,English Series 2024年第2期40卷 425-434页

作者： jing Jun han Yu Jie LUO Shanghai Center for Mathematical Sciences Fudan UniversityJiangwan CampusShanghai 200438P.R.China Department of Mathematics Johns Hopkins UniversityBaltimoreMD 21218USA

Following Shokurov's idea,we give a simple proof of the ACC conjecture for minimal log discrepancies for surfaces.

关键词： Ascending chain condition minimal log discrepancies minimal model program surface

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Elevational distribution of forests and its spatiotemporal dynamics in subtropical China from 2000 to 2019

引用

Science China Earth Sciences 2024年第8期67卷 2563-2582页

作者： Zhencan ZHENG Liuwen ZHUANG Guofang MIAO han LIU Zhiqiang cheng Wenyu LI Rong ShanG Peng GONG jing Ming CHEN Institute of Geography Fujian Normal University Key Laboratory of Humid Subtropical Eco-Geographical Process (Ministry of Education) Fujian Normal University School of Geographical Sciences Fujian Normal University National Land Consolidation Center Ministry of Natural Resources Key Laboratory of Land Consolidation and Rehabilitation Ministry of Natural Resources Key Laboratory of Digital Mapping and Land Information Application Ministry of Natural Resources Department of Geography & Planning University of Toronto Department of Geography The University of Hong Kong

The subtropical region of China possesses abundant forest resources and features a mountainous *** the implementation of policies such as natural forest protection,the Grain for Green Project,and other initiatives since the beginning of the 21st century,coupled with climate change,the forest resources in this region have undergone significant changes compared to historical *** addition,forest resources distributing mainly in mountainous areas also implies that these changes may vary significantly with *** explore the spatiotemporal dynamics of forest distribution in subtropical China since 2000,especially the trend of changes with elevation,we analyzed the data from two land cover products focusing on forest cover and forest *** used a hierarchical approach,in which coarse-classification forest cover data with relatively small uncertainties impose constraints on forest type data with larger uncertainties,to achieve a reasonable balance between obtaining more details and reducing data *** first divided the forest cover data into‘unchanged'and‘changed'*** the constraints by the forest cover results,we further analyzed the‘unchanged'and‘changed'forest *** results indicated that,since the implementation of ecological engineering and management policies,54%of the area in the subtropical region had maintained unchanged forest cover attributes over the past 20 years,which implied the good state of ecological *** results also showed that dynamic conversions existed in the long term between forests and lands for essential production needs like *** elevational variations of forest cover suggested that the dominant changes came from the conversion between forests and croplands in low-elevation regions below 700 m,the conversion between forests and shrublands in mid-elevation regions of 700–1500 m,and the conversion between forests and grasslands in high-elevation regions above 2000 *** the regio

关键词： Subtropical China Land cover Forest cover Forest type Elevational distribution

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Experimental and numerical study on dynamic mechanical behaviors of shale under true triaxial compression at high strain rate

引用

International Journal of Mining Science and Technology 2024年第2期34卷 149-165页

作者： Xiaoping Zhou Linyuan han jing Bi Yundong Shou School of Civil Engineering Wuhan UniversityWuhan 430072China College of Civil Engineering Guizhou UniversityGuiyang 550025China

High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing *** effectively extract shale gas,it is important to understand the dynamic mechanical properties of *** experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this *** dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are *** results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate *** characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial ***,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of *** dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D *** numerical results are in good agreement with the experimental data.

关键词： Dynamic behaviors True triaxial compression High strain rates Dynamic failure mechanism PFC3D-FLAC3D coupled method

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：