检索结果-南通市图书馆

Reinforcing effects of polypropylene on energy absorption and fracturing of cement-based tailings backfill under impact loading

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 2024年第4期31卷 650-664页

作者： Jiajian Li Shuai Cao erol Yilmaz School of Civil and Resources Engineering University of Science and Technology BeijingBeijing 100083China State Key Laboratory of High-Efficient Mining and Safety of Metal Mines of Ministry of Education University of Science and Technology BeijingBeijing 100083China Department of Civil Engineering Geotechnical DivisionRecep Tayyip Erdogan UniversityFenerRize TR53100Turkey

Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground ***,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast *** paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)*** Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of *** outcomes confirmed fiber aggregation at the bottom of *** H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°*** the total energy,all samples presented similar energy absorption,reflectance,and ***,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit *** increase in H/D resulted in a decreased crack volume fraction of *** the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence *** cracks were present only in the FRCTB with an H/D ratio of *** with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged *** fibers can limit the emergence and expansion of cracks by influencing their *** observations revealed considerable differences in the bonding strengths between fibers and the *** that adhered particularly well to the substrate were attracted together with the hydration products adhering to *** results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.

关键词： cement-based tailings fiber-reinforced backfills fracture energy absorption impact loading

A new Late Miocene Hystrix(Hystricidae,Rodentia)from Turkey

在线全文

学校读者我要写书评

暂无评论

Integrative Zoology 2024年第3期19卷 548-563页

作者： Kazım HALAÇLAR Ayla SEVIM erol Tolga KÖROG˘lu Paul RUMMY Tao DENG Serdar MAYDA Natural History Application and Research Centre Ege UniversityTurkey Key Laboratory of Vertebrate Evolution and Human Origins Institute of Vertebrate Paleontology and PaleoanthropologyChinese Academy of SciencesBeijingPeople’s Republic of China Department of Anthropology Faculty of Languages and HistoryGeographyAnkara UniversityTurkey Department of Biology Faculty of SciencesEge UniversityTurkey

TheÇorakyerler fossil locality in Anatolia reveals unique faunal *** study introduces Hystrix kayae ***.,a new Late Miocene porcupine initially classified as Hystrix *** et al.,*** finding expands our knowledge of Late Miocene Anatolian porcupines,bringing the total number of known species to *** *** larger than Hystrix aryanensis and exhibits greater upper cheek tooth crown *** cheek tooth morphology differs from Hystrix depereti,and it possesses distinctive U-shaped choanae unlike Hystrix ***Çorakyerler locality may predate sites with *** and *** but aligns temporally with Hystrix parvae *** study enhances our understanding of Late Miocene porcupine diversity in Anatolia,emphasizing the importance ofÇorakyerler in unraveling the evolutionary history of these fascinating mammals.

关键词： Çorakyerler Hystrix Late Miocene paleobiogeography Turkey

Microstructural evolution and strengthening mechanism of aligned steel fiber cement-based tail backfills exposed to electromagnetic induction

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 2024年第11期31卷 2390-2403页

作者： Xihao Li Shuai Cao erol Yilmaz School of Civil and Resources Engineering University of Science and Technology BeijingBeijing 100083China State Key Laboratory of High-Efficient Mining and Safety of Metal Mines of Ministry of Education University of Science and Technology BeijingBeijing 100083China Department of Civil Engineering Geotechnical DivisionRecep Tayyip Erdogan UniversityFener Rize TR53100Turkey

Cemented tailings backfill(CTB)not only boosts mining safety and cuts surface environmental pollution but also recovers ores previously retained as pillars,thereby improving resource *** use of alternative reinforcing products,such as steel fiber(SF),has continuously strengthened CTB into *** approach prevents strength decreases over time and reinforces its long-term durability,especially when mining ore in adjacent underground *** this study,various microstructure and strength tests were performed on SFCTB,considering steel fiber ratio and electromagnetic induction strength *** findings show that combining steel fibers and their distribution dominantly influences the improvement of the fill’s ***’s strength rises by fiber insertion and has an evident correlation with fiber insertion and magnetic induction *** magnetic induction strength is 3×10^(-4) T,peak uniaxial compressive stress reaches 5.73 MPa for a fiber ratio of 2.0vol%.The cracks’expansion mainly started from the specimen’s upper part,which steadily expanded downward by increasing the load until damage *** doping of steel fiber and its directional distribution delayed crack *** the doping of steel fiber was 2.0vol%,SFCTBs showed excellent ductility *** energy required for fills to reach destruction increases when steel-fiber insertion and magnetic induction strength *** study provides notional references for steel fibers as underground filling additives to enhance the fill’s durability in the course of mining operations.

关键词： electromagnetic induction steel fiber cemented tailings backfill strength microstructure

Continuous flow pyrolysis of virgin and waste polyolefins:a comparative study,process optimization and product characterization

在线全文

学校读者我要写书评

暂无评论

Frontiers of Chemical Science and Engineering 2024年第6期18卷 133-149页

作者： Ecrin Ekici Güray Yildiz Magdalena Joka Yildiz Monika Kalinowska erolŞeker Jiawei Wang Karlsruhe Institute of Technology Institute of Catalysis Research and TechnologyEggenstein-Leopoldshafen 76344Germany Izmir Institute of Technology Faculty of EngineeringDepartment of Energy Systems EngineeringIzmir 35430Türkiye Department of Materials Engineering and Production Faculty of Mechanical EngineeringBialystok University of TechnologyBialystok 15-351Poland Department of Agricultural and Food Engineering and Environmental Development Institute of Civil Engineering and EnergeticsFaculty of Civil Engineering and Environmental SciencesBialystok University of Technology15-351 BialystokPoland Department of Chemistry Biology and BiotechnologyInstitute of Civil Engineering and EnergeticsFaculty of Civil Engineering and Environmental SciencesBialystok University of TechnologyBialystok 15-351Poland Izmir Institute of Technology Faculty of EngineeringDepartment of Chemical EngineeringIzmir 35430Türkiye Energy and Bioproducts Research Institute(EBRI) Aston UniversityBirmingham B47ETUnited Kingdom

Under optimal process conditions,pyrolysis of polyolefins can yield ca.90 wt%of liquid product,i.e.,combination of light oil fraction and heavier *** this work,the experimental findings reported in a selected group of publications concerning the non-catalytic pyrolysis of polyolefins were collected,reviewed,and compared with the ones obtained in a continuously operated bench-scale pyrolysis *** process parameters were used for the pyrolysis of waste and virgin counterparts of high-density polyethylene,low-density polyethylene,polypropylene and a defined mixture of those(i.e.,25:25:50 wt%,respectively).To mitigate temperature drops and enhance heat transfer,an increased feed intake is employed to create a hot melt plastic *** 1.5 g·min^(-1) feed intake,1.1 L·min^(-1) nitrogen flow rate,and a moderate pyrolysis temperature of 450℃,the formation of light hydrocarbons was favored,while wax formation was limited for polypropylene-rich *** of virgin plastics yielded more liquid(maximum 73.3 wt%)than that of waste plastics(maximum 66 wt%).Blending polyethylenes with polypropylene favored the production of liquids and increased the formation of gasoline-range *** products were mainly composed of C3 hydrocarbons,and no hydrogen production was detected due to moderate pyrolysis temperature.

关键词： waste plastics polyolefins chemical recycling pyrolysis alternative fuels waste-to-energy

基于离散元-有限差分耦合的轨枕垫对有砟道床横向阻力的影响机制

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

中南大学学报（自然科学版） 2024年第2期55卷 457-472页

作者：谭攀肖源杰姜钰王萌王小明张冲冲 TUTUMluER erol 中南大学土木工程学院湖南长沙410075 重载铁路工程结构教育部重点实验室(中南大学) 湖南长沙410075 伊利诺伊大学香槟分校香槟61801美国

轨枕垫(USP)因其良好的减震性能已广泛应用于铁路轨道结构,现有研究大多集中于USP对轨道结构刚度和振动响应的影响,但对有砟道床横向阻力影响的研究很少。为深入分析USP对道床横向阻力的影响并揭示其作用机理,建立轨枕-USP-有砟道床-路... 详细信息

轨枕垫(USP)因其良好的减震性能已广泛应用于铁路轨道结构,现有研究大多集中于USP对轨道结构刚度和振动响应的影响,但对有砟道床横向阻力影响的研究很少。为深入分析USP对道床横向阻力的影响并揭示其作用机理,建立轨枕-USP-有砟道床-路基三维系统的精细化离散元-有限差分(DEM-FDM)耦合数值模型,采用典型重载铁路有砟道床横向阻力现场实测结果对模型进行标定和验证,进而模拟分析不同工况组合下USP对轨枕不同位置处(枕底、枕侧和枕端)的横向阻力、道砟颗粒运动和粒间接触力等宏微观指标的影响机制。研究结果表明:在相同的轨枕横向位移下,相较于无USP的轨枕,带USP的轨枕其枕底道砟颗粒运动范围更大,横向阻力也更大,且横向阻力增加部分主要来源于枕底USP的不平整性;USP刚度越大,道床横向阻力也越大;采用USP可增加枕底的横向剪应力和最大法向接触力,且两者数值均随USP刚度的增大而增大。

关键词：铁路轨道有砟道床道砟轨枕垫横向阻力离散元-有限差分耦合

NEW POLY(METHACRYLATE)S CONTAINING OXIME ESTERS MOIETIES BASED ON CYCLOHEXANON AND CYCLOPENTANON

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Polymer Science 2008年第4期26卷 443-454页

作者： Ibrahim erol Afyon Kocatepe Universty Faculty of Science and Arts Department of ChemistryAfyonkarahisarTurkey

The synthesis of two new methacrylates such as 2-[(cyclohexylideneamino)oxy]-2-oxoethyl methylacrylate (CHOEMA)and 2-[(cyclopentylideneamino)oxy]-2-oxoethyl methylacrylate(CPOEMA)are *** monomers produced from the reaction of corresponding cyclohexanone O-(2-chloroacetyl)oxime and cyclopentanone O-(2- chloroacetyl)oxime with sodium methacrylate was polymerized in 1,4-dioxane solution at 65℃using AIBN as an initiator. The monomers and their polymers were characterized by IR,~1H- and ^(13)C-NMR spec...

关键词： Methacrylate Oxime esters Activation energy Thermal decompositionv Biological activitiy

SYNTHESIS AND CHARACTERIZATION OF A METHACRYLATE POLYMER WITH SIDE CHAIN KETONE AND ITS DERIVATIVES

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Polymer Science 2011年第1期29卷 101-110页

作者： Ibrahim erol Cemal Cifci Department of Chemistry Faculty of Arts and ScienceUniversity of Afyon KocatepeAfyonkarahisarTurkey

A new type of methacrylate monomer, 2-（4-benzoylphenoxy）-2-oxoethyl methylacrylate （BOEMA） was synthesized. The radical homopolymerization of BOEMA was performed at 65℃ in a 1,4-dioxane solution with benzoyl peroxide as an initiator. The oxime and thiosemicarbazone derivatives of poly[2-（4-benzoylphenoxy）-2-oxoethyl methylacrylate] poly（BOEMA） were prepared with hydroxylamine hydrochloride, and thiosemicarbazone hydrochloride, respectively. The monomer and its homopolymer were characterized with Fourier transform infrared and NMR techniques. The thermal stabilities of poly（BOEMA） and its derivatives were investigated with thermogravimetric analysis and differential scanning calorimetry. The ultraviolet stability of the polymers was compared. The antibacterial and antifungal effects of the monomer and the polymer and its derivatives were also investigated on various bacteria and fungi. The activation energies of the thermal degradation of the polymers were calculated with the Ozawa and Kissinger methods.

关键词： Acetyl group Ethylene dimethacrylate Oxime Thermal stability Biological activity Activation energies

Progress and prospects of mining with backfill in metal mines in China

在线全文

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 2023年第8期30卷 1455-1473页

作者： Gaili Xue erol Yilmaz Yongding Wang College of Mining Technology Taiyuan University of TechnologyTaiyuan030024China Research Center of Green Mining Engineering Technology in Shanxi Province Taiyuan030024China Department of Civil Engineering Geotechnical DivisionRecep Tayyip Erdogan UniversityFenerRizeTR53100Turkey Longshou Mine Jinchuan Group Co.Ltd.Jinchuan737100China

Mining is the foundation of modern industrial *** the context of the“carbon peaking and carbon neutrality”era,countries have put forward the development strategy of“adhering to the harmonious coexistence of humans and nature.”The ongoing progress and improvement of filling mining technology have provided significant advantages,such as“green mining,safe,efficient,and low-carbon emission,”which is crucial to the comprehensive utilization of mining solid waste,environmental protection,and safety of *** review paper describes the development history of metal mine filling mining in China and the characteristics of each *** excitation mechanism and current research status of producing cementitious materials from blast furnace slag and other industrial wastes are then presented,and the concept of developing cementitious materials for backfill based on the whole solid waste is *** advances in the mechanical characteristics of cemented backfill are elaborated on four typical levels:static mechanics,dynamic mechanics,mechanical influencing factors,and multi-scale *** working/rheological characteristics of the filling slurry are presented,given the importance of the filling materials conveying ***,the future perspectives of mining with backfill are discussed based on the features of modern filling concepts to provide the necessary theoretical research value for filling mining.

关键词： mining with backfill cementitious materials mechanical characteristics slurry properties future perspectives

Effects of magnet shapes on total harmonic distortion and cogging torque in a permanent magnet synchronous generator for wind turbines

在线全文

学校读者我要写书评

暂无评论

Clean Energy 2023年第5期7卷 1058-1068页

作者： erol Kurt Adem Dalcalı Gazi University Department of Electrical and Electronics EngineeringTechnology FacultyAnkaraTurkey Bandırma Onyedi Eylul University Department of Electrical and Electronics EngineeringFaculty of Engineering and Natural SciencesBandırmaBalıkesirTurkey National Research University TIIAME100000TashkentUzbekistan

This paper explores and theoretically reports the effects of different magnet structures on the cogging torque and the total harmonic distortion of the output waveforms from a permanent magnet *** generator is a radial flux machine and four different structures are considered for the magnet arrangement in the rotor component and modelled in the Ansys/Maxwell electromagnetic simulation *** three-phase machine exhibits different behaviours towards various magnet structures,***,inclined slotted rectangular,skewed double rectangular and inclined slotted skewed double rectangular,*** has been proven by finite element analysis and Fourier analysis that both the cogging and total harmonic distortion values vary significantly for all *** cogging torque values change in the range of 89.95 to 436.75 mNm and the lowest cogging torque is measured for the inclined slotted skewed double rectangular magnet geometry,while the conventional rectangular magnet geometry yields the worst value with 436.75 ***,the total harmonic distortion values varies between 1.63 and 3.55 for different magnetic *** the worst total harmonic distortion value is obtained from the inclined slotted rectangular magnet,the best total harmonic distortion is acquired from the skewed double rectangular *** these results will provide scientists and engineers with important information in order to obtain more efficient machines.

关键词： renewable energy wind power finite element method synchronous generator wind turbines