检索结果-南通市图书馆

Science China(Technological Sciences) 2024年第8期67卷 2436-2448页

作者： ZHU YanLong LI SuNing FAN JianHua KONG WeiQiang yuan yuan TAN HePing School of Energy Science and Engineering Harbin Institute of TechnologyHarbin 150001China Department of Civil Engineering and Mechanical Engineering Technical University of DenmarkKoppels AlléBuilding 4042800 Kgs.LyngbyDenmark School of Vehicle and Energy Yanshan UniversityQinhuangdao 066004China

In this study, a novel model of photothermal conversion in a direct absorption solar collector based on the Monte Carlo and finite volume methods was built and validated and the temperatures of the novel and traditional solar collectors were compared. The sensitivity of the parameters to the radiative heat loss was investigated. Finally, the radiative heat transfer characteristics were discussed using the radiative exchange factor. The results of this study validated the advantages of the novel solar collector at both the surface and fluid temperatures. Under the conditions used in this study, the maximum temperature difference of the novel solar collector was 30 K, compared with 193 K for the traditional solar collector. Furthermore, the collector was divided into several units along the flow direction. The radiative exchange factor indicated that with an increase in the attenuation coefficient, the percentage of radiation intensity in the total solar radiation absorbed by the corresponding unit ***, it decreased with an increase in the incident angle and scattering albedo. These results provide a reference for addressing the low efficiency and thermal damage caused by traditional solar collectors at high temperatures.

关键词： direct absorption solar collector radiative heat transfer Monte Carlo

Tribological evaluation of thermoplastic polyurethane-based bearing materials under water lubrication:Effect of load,sliding speed,and temperature

在线全文

学校读者我要写书评

暂无评论

Friction 2024年第8期12卷 1801-1815页

作者： Shaoli JIANG Janet SSWONG Debashis PUHAN Tian yuan Xiuqin BAI Chengqing yuan State Key Laboratory of Maritime Technology and Safety Wuhan University of TechnologyWuhan 430063China Department of Mechanical Engineering Imperial College LondonLondon SW72AZUK Yusuf Hamied Department of Chemistry University of CambridgeLensfield RoadCambridge CB21EWUK

Polymers are widely used in bearing *** the case of water-lubricated stern tube bearings,thermoplastic polyurethane(TPU)-based composites are used due to their excellent wear resistance,corrosion resistance,and tunable mechanical *** tribological performance,however,depends on operating *** this work,TPU was blended with carbon fiber,graphene platelet,and ultra-high molecular weight polyethylene(UHMWPE).Friction tests of TPU based-composites against copper countersurface were carried out in water to mimic the actual operating conditions of the *** of the resulting contacts were in the boundary lubrication regime,in which friction was attributed to both contact mechanics of asperities as well as water *** results show that the viscoelasticity of TPU has a considerable impact on its tribological *** lubrication at 50°C promotes the softening of polymer surface material during sliding,resulting in higher fluctuation in the coefficient of friction and wear *** is attributed to the reduced thermomechanical *** addition,Schallamach waviness is observed on worn *** tribological properties of TPU are significantly improved by the inclusion of carbon fiber,graphene platelet,and *** formation of graphene transfer-layers and UHMWPE transfer film reduces friction and wear loss,while the inclusion of carbon fiber enhances wear resistance due to improved mechanical properties and load bearing capacity.

关键词： friction thermoplastic polyurethane(TPU) water-lubricated bearings graphene platelet carbon fibers ultra-high molecular weight polyethylene(UHMWPE)

Single-atom Ag-loaded carbon nitride photocatalysts for efficient degradation of acetaminophen:The role of Ag-atom and O_(2)

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Environmental Sciences 2024年第5期139卷 12-22页

作者： Yi yuan Wen-Long Wang Zhi-Wei Wang Jin Wang Qian-yuan Wu Key Laboratory of Microorganism Application and Risk Control of Shenzhen Guangdong Provincial Engineering Research Center for Urban Water Recycling and Environmental SafetyInstitute of Environment and EcologyShenzhen International Graduate SchoolTsinghua UniversityShenzhen 518055China Shenzhen Environmental Science and New Energy Technology Engineering Laboratory Tsinghua-Berkeley Shenzhen InstituteShenzhen 518055China College of Materials Science and Engineering Shenzhen UniversityShenzhen 518071China

Carbon nitride has been extensively used as a visible-light photocatalyst,but it has the disadvantages of a low specific surface area,rapid electron-hole recombination,and relatively low light *** this study,single-atom Ag was successfully anchored on ultrathin carbon nitride(UTCN)via thermal polymerization,the catalyst obtained is called *** Ag hardly changed the carbon nitride's layered and porous physical *** exhibited efficient visible-light photocatalytic performances in the degradation of various recalcitrant pollutants,eliminations of 85% were achieved by visible-light irradiation for *** with Ag improved the photocatalytic performance of UTCN by narrowing the forbidden band gap from 2.49 to 2.36 e V and suppressing electron-hole pair *** addition,Ag doping facilitated O_(2) adsorption on UTCN by decreasing the adsorption energy from -0.2 to -2.22 e V and favored the formation of O_(2)^(·-).Electron spin resonance and radical-quenching experiments showed that O_(2)^(·-)was the major reactive species in the degradation of Acetaminophen(paracetamol,APAP).

关键词： Ag single atom Carbon nitride Photocatalysis Visible light Adsorption energy Reactive species

Outlier item detection in bundle recommendation via the attention mechanism

在线全文

学校读者我要写书评

暂无评论

High-Confidence Computing 2024年第3期4卷 51-57页

作者： yuan Liang School of Information Engineering Suqian UniversitySuqian 223800China Guangxi Key Laboratory of Trusted Software Guilin University of Electronic TechnologyGuilin 541004China

Bundle recommendation offers users more holistic insights by recommending multiple compatible items at ***,the intricate correlations between items,varied user preferences,and the pronounced data sparsity in combinations present significant challenges for bundle recommendation ***,current bundle recommendation methods fail to identify mismatched items within a given set,a process termed as‘‘outlier item detection’’.These outlier items are those with the weakest correlations within a *** them can aid users in refining their item *** the correlation among items can predict the detection of such outliers,the adaptability of combinations might not be adequately responsive to shifts in individual items during the learning *** limitation can hinder the algorithm’s *** tackle these challenges,we introduce an encoder–decoder architecture tailored for outlier item *** encoder learns potential item correlations through a self-attention ***,the decoder garners efficient inference frameworks by directly assessing item *** have validated the efficacy and efficiency of our proposed algorithm using real-world datasets.

关键词： Bundle recommendation Outlier item detection Attention mechanism Decoder encoder

Competition of Composition Fluctuation Modes in Weakly Segregated Salt-doped Symmetric Diblock Copolymers

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Chinese Journal of Polymer Science 2024年第9期42卷 1375-1385,I0008页

作者： yuan-Xin Zhou Xian Kong South China Advanced Institute for Soft Matter Science and Technology School of Emergent Soft MatterSouth China University of TechnologyGuangzhou510640China Guangdong Provincial Key Laboratory of Functional and Intelligent Hybrid Materials and Devices South China University of TechnologyGuangzhou510640China

Salt-doped block copolymers have widespread applications in batteries,fuel cells,semiconductors,and various industries,where their properties crucially depend on phase separation ***,investigations into salt-doped diblock copolymers have predominantly focused on microphase separation,overlooking the segregation between ionic and polymeric *** study employs weak segregation theory to explore the interplay between phase separation dominated by the polymer-modulated mode and the salt-out-modulated mode,corresponding to microscopic and macroscopic phase separations,*** comparing diblock copolymers doped with salts to those doped with neutral solvents,we elucidate the significant role of charged species in modulating phase *** phase separation mode exhibits a transition between the polymer-modulated and salt-out-modulated modes at different *** systems doped with neutral solvents,this transition is stepwise,while in salt-ion-doped systems,it is *** a sufficiently large Flory-Huggins parameter between ions and polymers,the salt-out-modulated mode becomes dominant,promoting macrophase *** to the solvation effect of salt ions,salt-doped systems are more inclined to undergo microphase ***,we explore factors influencing the critical wavenumber of phase separation,including doping level and the Flory-Huggins parameters between two blocks and between ions and polymeric *** findings reveal that in a neutral solvent environment,these factors alter only the boundary between micro-and macro-phase separations,leaving the critical wavenumber unchanged in microphase separation ***,in a salt-doped environment,the critical wavenumber of microphase separation varies with these *** provides valuable insights into the pivotal role of electrostatics in the phase separation of salt-doped block copolymers.

关键词： Block copolymer Phase separation Field theory Salt-doped

Development of component stiffness equations for thread-fixed one-side bolt connections to an enclosed rectangular hollow section column under tension

在线全文

学校读者我要写书评

暂无评论

Frontiers of Structural and Civil Engineering 2024年第4期18卷 568-586页

作者： Fu-Wei WU yuan-Qi LI Department of Structural Engineering Tongji UniversityShanghai 200092China State Key Laboratory of Disaster Reduction in Civil Engineering Tongji UniversityShanghai 200092China

The derivation and validation of analytical equations for predicting the tensile initial stiffness of threadfixed one-side bolts(TOBs),connected to enclosed rectangular hollow section(RHS)columns,is presented in this *** unknown stiffness components are considered:the TOBs connection and the enclosed RHS ***,the trapezoidal thread of TOB,as an equivalent cantilevered beam subjected to uniformly distributed loads,is analyzed to determine the associated *** on the findings,the thread-shank serial-parallel stiffness model of TOB connection is *** analysis of the tensile stiffness of the enclosed RHS face due to two bolt forces,the four sidewalls are treated as rotation constraints,thus reducing the problem to a two-dimensional plate *** to the load superposition method,the deflection of the face plate is resolved into three components under various boundary and load *** to the plate deflection theory of Timoshenko,the analytical solutions for the three deflections are derived in terms of the variables of bolt spacing,RHS thickness,height to width ratio,***,the validity of the above stiffness equations is verified by a series of finite element(FE)models of T-stub *** proposed component stiffness equations are an effective supplement to the component-based method.

关键词： initial stiffness component based method thread-fixed one-side bolt rectangular hollow sections analytical equation

Reliability-based life-cycle cost seismic design optimization of coastal bridge piers with nonuniform corrosion using different materials

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Earthquake Engineering and Engineering Vibration 2024年第1期23卷 209-225页

作者： Wu Xiangtong yuan Wenting Guo Anxin Key Lab of Smart Prevention and Mitigation of Civil Engineering Disasters of the Ministry of Industry and Information Technology Harbin Institute of TechnologyHarbin 150090China Key Lab of Structures Dynamic Behavior and Control of the Ministry of Education Harbin Institute of TechnologyHarbin 150090China Institute of Transportation Inner Mongolia UniversityHohhot 010070China

Reinforcement corrosion is the main cause of performance deterioration of reinforced concrete(RC)*** research has been performed to investigate the life-cycle cost(LCC)of coastal bridge piers with nonuniform corrosion using different *** this study,a reliability-based design optimization(RBDO)procedure is improved for the design of coastal bridge piers using six groups of commonly used materials,i.e.,normal performance concrete(NPC)with black steel(BS)rebar,high strength steel(HSS)rebar,epoxy coated(EC)rebar,and stainless steel(SS)rebar(named NPC-BS,NPC-HSS,NPC-EC,and NPC-SS,respectively),NPC with BS with silane soakage on the pier surface(named NPC-Silane),and high-performance concrete(HPC)with BS rebar(named HPC-BS).First,the RBDO procedure is improved for the design optimization of coastal bridge piers,and a bridge is selected to illustrate the ***,reliability analysis of the pier designed with each group of materials is carried out to obtain the time-dependent reliability in terms of the ultimate and serviceability ***,the repair time of the pier is predicted based on the time-dependent reliability ***,the time-dependent LCCs for the pier are obtained for the selection of the optimal design.

关键词： reliability-based design optimization(RBDO) life-cycle cost(LCC) nonuniform corrosion coastal bridge pier repair

Trial application of the envelope method to the potential ambiguity problem

在线全文

学校读者我要写书评

暂无评论

Nuclear Science and Techniques 2024年第1期35卷 73-80页

作者： Li-yuan Hu Yu-Shou Song Fundamental Science on Nuclear Safety and Simulation Technology Laboratory Harbin Engineering UniversityHarbin 150001China College of Nuclear Science and Technology Harbin Engineering UniversityHarbin 150001China Key Laboratory of Nuclear Safety and Advanced Nuclear Energy Technology Ministry of Industry and Information TechnologyHarbin 150001China

The optical potential ambiguity is a long-standing problem in the analysis of elastic scattering *** a specific collid-ing system,ambiguous potential families can lead to different behaviors in the nearside and farside scattering *** contrast,the envelope method can decompose the experimental data into two components with negative and positive deflection angles,***,a question arises as to whether the comparison between the calculated nearside(or farside)component and the derived positive-deflection-angle(or negative-deflection-angle)component can help analyze the potential ambiguity *** this study,we conducted a trial application of the envelope method to the potential ambiguity *** envelope method was improved by including uncertainties in the experimental *** colliding systems of 16O+28Si at 215.2 MeV and 12C+12C at 1016 MeV were considered in the *** each colliding system,the angular distribution experimental data were described nearly equally well by two potential sets,one of which is“surface transpar-ent”and the other is *** calculated angular distributions were decomposed into nearside and farside scattering *** the improved envelope method,the experimental data were decomposed into the positive-deflection-angle and negative-deflection-angle components,which were then compared with the calculated nearside and farside *** capability of the envelope method to analyze the potential ambiguities was also discussed.

关键词： Elastic scattering Optical potential ambiguities Envelope method Nearside/farside decomposition

Deep electrical structures of Qinzhou-Fangcheng Junction Zone in Guangxi and seismogenic environment of the 1936 Lingshan M6^(3/4)earthquake

在线全文

学校读者我要写书评

暂无评论

Science China Earth Sciences 2024年第2期67卷 584-603页

作者： Bin ZHOU Chunheng YAN Yan ZHAN Xiangyu SUN Sha LI Xiang WEN Yajun MO Yongdong yuan yuan yuan Meili HUANG Earthquake Agency of Guangxi Zhuang Autonomous Region Nanning530022China State Key Laboratory of Earthquake Dynamics Institute of GeologyChina Earthquake AdministrationBeijing100029China Guangxi Geophysical Survey Institute Liuzhou545005China

The tectonic position of the southwest section of the Qinzhou Bay-Hangzhou Bay Tectonic Junction Zone(QHTJZ)can be determined by examining the Qinzhou-Fangcheng Junction Zone(QFJZ)in *** zone is significant because it was the location of the largest earthquake ever recorded in the inland region of South China,specifically the 1936 Lingshan M6^(3/4)earthquake in ***,this region serves as an optimal location for researching the origins of intraplate earthquakes in South *** study presents a display of a broadband magnetotelluric(MT)prospecting profile that traverses the Guangxi QFJZ and the Lingshan earthquake zone,extending from the northwest(NW)to the southeast(SE).A resistivity structure model was generated using three-dimensional(3D)inversion technology along the *** main faults in QFJZ were analyzed in terms of their deep extension forms and tectonic *** analysis was performed by integrating the results obtained from geology,gravity,wave velocity ratio,Global Position System(GPS),and geothermal *** results showed that(1)the Dongzhong-Xiaodong fault(DXf),the eastern Fangcheng-Lingshan fault(FLf2),and the eastern Hepu-Beiliu fault(HBf2)were all trans-crustal deep faults,and crust-mantle ductile shear zones developed in the deep *** electrical boundary zones,DXf and HBf2,were *** inclined towards the northwest,while HBf2 inclined towards the *** FangchengLingshan fault(FLf)exhibits a tectonic style resembling a“flower”shape in the upper *** the deeper section,it is characterized by an electrical boundary zone that gradually slopes towards the southeast direction.(2)The Hunan-Guangxi Passive Continental Margin(HGPCM)on the NW side of DXf had a stratified resistivity structure and relatively stable Bouguer gravity anomalies,which conformed to the quasi-craton tectonic attribute of the local failure at the southeastern margin of the Yangtze Block(YB).The southeastern side of this bloc

关键词： South China Block Qinzhou-Fangcheng Junction Zone Magnetotelluric 1936 Lingshan M6^(3/4)earthquake Deep seismogenic environment

Oxygen reduction electrocatalysis:From conventional to single-atomic platinum-based catalysts for proton exchange membrane fuel cells

在线全文

学校读者我要写书评

暂无评论

Frontiers in Energy 2024年第2期18卷 206-222页

作者： Cheng yuan Shiming ZHANG Jiujun ZHANG Institute for Sustainable Energy/College of Sciences Shanghai UniversityShanghai 200444China

Platinum(Pt)-based materials are still the most efficient and practical catalysts to drive the sluggish kinetics of cathodic oxygen reduction reaction(ORR)in proton exchange membrane fuel cells(PEMFCs).However,their catalysis and stability performance still need to be further improved in terms of corrosion of both carbon support and Pt catalyst particles as well as Pt loading *** on the developed synthetic strategies of alloying/nanostructuring Pt particles and modifying/innovating supports in developing conventional Pt-based catalysts,Pt single-atom catalysts(Pt SACs)as the recently burgeoning hot materials with a potential to achieve the maximum utilization of Pt are comprehensively reviewed in this *** design thoughts and synthesis of various isolated,alloyed,and nanoparticlecontained Pt SACs are *** single-atomic Pt coordinating with non-metals and alloying with metals as well as the metal-support interactions of Pt single-atoms with carbon/non-carbon supports are emphasized in terms of the ORR activity and stability of the *** advance further research and development of Pt SACs for viable implementation in PEMFCs,various technical challenges and several potential research directions are outlined.

关键词： oxygen reduction electrocatalysis Pt singleatom catalysts conventional Pt-based catalysts design thoughts and synthesis metal-support interactions