检索结果-南通市图书馆

Prediction of liquid circulation flow rate in RH degasser:improvement of decarburization at low atmospheric pressure

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第7期31卷 1661-1667页

作者： Gu-jun Chen Sheng-ping He College of Materials Science and Engineering Yangtze Normal UniversityChongqing 400044China College of Materials Science and Engineering Chongqing UniversityChongqing 400044China

The two-fluid model coupled with population balance model was used for simulating the gas-liquid flow in the Ruhrstahl-Heraeus(RH)*** predicted circulation flow rate was compared with that measured from a water model experiment to validate the mathematical ***,influence of snorkel immersion depth on liquid circulation flow rate was numerically investigated under an atmospheric pressure of 101 and 84 kPa,*** result indicates that the circulation flow rate of the RH degasser in the high-altitude area was severely reduced because of the decrease in atmospheric ***,increasing the snorkel immersion depth from 0.5 to 0.7 m can compensate for the decrease in atmospheric *** test result indicates that decarburization rate is significantly enhanced by increasing the snorkel immersion *** optimization,the percentage of heats with a final carbon content less than 0.002 wt.%is significantly increased from 22.0%to 96.4%.

关键词： RH degasser Two-fluid model Population balance model-Circulation flow rate Decarburization Snorkel immersion depth

Volume of fluid simulation of single argon bubble dynamics in liquid steel under RH vacuum conditions

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2024年第4期31卷 828-837页

Single argon bubble dynamics in liquid steel under Ruhrstahl-Heraeus(RH)vacuum conditions were simulated using the volume of fluid method,and the ideal gas law was used to consider bubble growth due to heat transfer and pressure *** simulation with a constant bubble density was also performed to validate the numerical method,and the predicted terminal bubble shape and velocity were found to agree with those presented in the Grace diagram and calculated by drag correlation,*** simulation results under RH conditions indicate that the terminal bubble shape and velocity cannot be *** primary bubble growth occurs within a rising distance of 0.3 m owing to heating by the high-temperature liquid steel;subsequently,the bubble continues to grow under equilibrium with the hydrostatic *** the initial diameter is 8-32 mm,the bubble diameter and rising velocity near the liquid surface are 80-200 mm and 0.5-0.8 m/s,*** bubble rises rectilinearly with an axisymmetric shape,and the shape evolution history includes an initial sphere,(dimpled)ellipsoid,and spherical cap with satellite bubbles.

关键词： Bubble dynamics Liquid steel Volume of fluid Bubble growth Bubble shape Rising velocity

Effects of the Rainfall-Triggered Lisse Effect on the Stability of Loess Slopes

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Earth Science 2024年第4期35卷 1254-1262页

作者： Zhizhou Yang Donghui Cheng jun xia School of Water and Environment Chang’an UniversityXi’an710054China Key Laboratory of Subsurface Hydrology and Ecological Effects in Arid Region of the Ministry of Education Chang’an UniversityXi’an710054China Key Laboratory of Eco-Hydrology and Water Security in Arid and Semi-Arid Regions of the Ministry of Water Resources Chang’an UniversityXi’an710054China Key Laboratory of Water Cycle&Related Land Surface Processes Institute of Geographic Sciences and Natural Resources ResearchChinese Academy of SciencesBeijing100101China State Key Laboratory of Water Resources&Hydropower Engineering Sciences Wuhan UniversityWuhan430000China

This paper coupled a water-air two-phase hydrodynamic(WATPH)model with the Iverson’s method to analyze the influence of the Lisse effect on the fast groundwater pressure(P_(w))response and the slope ***,the sensitivities of the driving force and loess soil parameters were *** showed that the WATPH model simulated the height and rise of the depth to the water table reasonably *** depth to water table before rainfall(H0)had a significant impact on the Lisse effect and the slope *** the H_(0) was less than approximately 1 m,the rainfall triggered a significant Lisse effect and decreased the slope factor of safety(F_(s)).When the rainfall intensity(R_(i))was higher than the saturated hydraulic conductivity(K_(s)),the Lisse effect and the F_(s) slightly changed with the increase of the R_(i),and the slope tended to be unstable with continuous *** increasing K_(s),the Lisse effect noticeably increased,and the minimum F_(s) quickly *** analysis of the normalized sensitivity coefficient revealed that H_(0) had a dramatic impact on the Lisse effect and loess slope *** different R_(i) and K_(s) values had prominent influences on the Lisse effect and slight impacts on F_(s).

关键词： Lisse effect landslides safety factor rainfall

DEM investigation of strength and critical state behaviours of granular materials under true triaxial loadings

在线全文

学校读者我要写书评

暂无评论

Particuology 2024年第2期85卷 198-212页

作者： Minyi Zhu Guobin Gong jun xia Stephen Wilkinson Department of Civil Engineering Xi'an Jiaotong-Liverpool UniversityChina Department of Civil Engineering and Industrial Design University of LiverpoolLiverpoolUK Faculty of Engineering and Information Sciences University of Wollongong in DubaiUnited Arab Emirates

This paper investigates the strength and critical state(CS)behaviours of granular materials via DEM simulations of true triaxial drained tests under three different loading modes including constant b(in-termediate stress ratio)tests with constantσ'1(major principal stress),constant p(mean pressure)and constantσ'3(minor principal stress)*** this end,a series of samples are generated with the same particle size distribution,and with the confining stresses ranging from 100 kPa to 900 *** CS is achieved for all *** the macroscopic behaviours and the microscopic behaviours are examined and compared considering different loading modes,confining stresses and intermediate stress ratios(b).The critical state lines(CSLs)are found to be unique and independent of the loading modes,but dependent on the b *** CSLs with b=0 and b=1 form the two boundaries of CSLs respectively beyond which CSLs under all other b tests cannot go *** different strength criteria are examined and compared in terms of both peak and CS *** Mohr-Coulomb strength criterion is found to be only suitable for axisymmetric loading *** Lade-Duncan criterion is only suitable for describing peak strengths,which is dependent on the loading modes and confining *** Satake criterion and Matsuoka-Nakai criterion are the more appropriate strength criteria for describing CS failures,indicating that the CS values of both the Satake parameter and the Matsuoka-Nakai parameter describe an inherent property that characterizes the CS failure for a given type of *** CS mechanical coordination number is fitted by a curved line for a given b value,which is unique regardless of the loading *** peak and CS values of both major and minor principal fabric tensors decrease with increasing b values,while they increase with increasing b values for the intermediate principal fabric tensor.

关键词： Discrete element method Intermediate stress ratio Dilation Critical state Failure criterion

Numerical simulations for radon migration and exhalation behavior during measuring radon exhalation rate with closed-loop method

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Nuclear Science and Techniques 2024年第1期35卷 81-95页

作者： Ming xia Yong-jun Ye Shu-Yuan Liu School of Resources Environment and Safety Engineering University of South ChinaHengyang 421001China Key Discipline Laboratory for National Defense for Biotechnology in Uranium Mining and Hydrometallurgy University of South ChinaHengyang 421001China

Accurate measurements of the radon exhalation rate help identify and evaluate radon risk regions in the *** these measurement methods,the closed-loop method is frequently ***,traditional experiments are insufficient or cannot analyze the radon migration and exhalation patterns at the gas–solid interface in the accumulation *** CFD-based technique was applied to predict the radon concentration distribution in a limited space,allowing radon accumulation and exhalation inside the chamber intuitively and *** this study,three radon exhalation rates were defined,and two structural ventilation tubes were designed for the *** consistency of the simulated results with the variation in the radon exhalation rate in a previous experiment or analytical solution was *** effects of the vent tube structure and flow rate on the radon uniformity in the chamber;permeability,insertion depth,and flow rate on the radon exhalation rate and the effective diffusion coefficient on back-diffusion were *** on the results,increasing the inser-tion depth from 1 to 5 cm decreased the effective decay constant by 19.55%,whereas the curve-fitted radon exhalation rate decreased(lower than the initial value)as the deviation from the initial value increased by approximately 7%.Increasing the effective diffusion coefficient from 2.77×10^(-7) to 7.77×10^(-6) m^(2) s^(-1) made the deviation expand from 2.14 to 15.96%.The conclusion is that an increased insertion depth helps reduce leakage in the chamber,subject to notable back-diffusion,and that the closed-loop method is reasonably used for porous media with a low effective diffusion coefficient in view of the back-diffusion *** CFD-based simulation is expected to provide guidance for the optimization of the radon exhalation rate measurement method and,thus,the accurate measurement of the radon exhalation rate.

关键词： Radon exhalation Numerical simulation Accumulation chamber

An adaptive energy regulation in a memristive map linearized from a circuit with two memristive channels

在线全文

学校读者我要写书评

暂无评论

Communications in Theoretical Physics 2024年第3期76卷 42-50页

作者： Feifei Yang ping Zhou jun Ma School of Science Chongqing University of Posts and TelecommunicationsChongqing 430065China College of Electrical and Information Engineering Lanzhou University of TechnologyLanzhou 730050China Department of Physics Lanzhou University of TechnologyLanzhou 730050China

Nonlinear circuits can show multistability when a magnetic flux-dependent memristor(MFDM) or a charge-sensitive memristor(CSM) is incorporated into a one branch circuit,which helps estimate magnetic or electric field *** this paper,two different kinds of memristors are incorporated into two branch circuits composed of a capacitor and a nonlinear resistor,thus a memristive circuit with double memristive channels is *** circuit equations are presented,and the dynamics in this oscillator with two memristive terms are ***,the memristive oscillator is converted into a memristive map by applying linear transformation on the sampled time series for the memristive *** Hamilton energy function for the memristive oscillator is obtained by using the Helmholtz theorem,and it can be mapped from the field energy of the memristive *** energy function for the dual memristive map is suggested by imposing suitable weights on the discrete energy *** dynamical behaviors of the new memristive map are investigated,and an adaptive law is proposed to regulate the firing mode in the memristive *** work will provide a theoretical basis and experimental guidance for oscillator-to-map transformation and discrete map energy calculation.

关键词： Hamilton energy dual memristive map adaptive energy regulation

Chain Extender-induced Hydrogen Bonding Organization Determines the Morphology and Properties of Thermoplastic Polycarbonate Polyurethane

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Polymer Science 2024年第1期42卷 87-96,I0009页

作者： Yi-Lang Qin ping Zhu Chen-Xi Ouyang xia Dong Fuwai Hospital Chinese Academyof Medical Sciences&Peking Union Medical College/National Center for Cardiovascular DiseasesBejing 100037China CASKey Laboratoryof Engineering Plastics CAS Research/Education Centerfor Excellence in Molecular SciencesInstitute ofChemistryChinese Academy of SciencesBeijing 100190China University of Chinese Academy of Sciences Beijing 100049China

Thermoplastic polycarbonate polyurethanes(PCUs) are multiblock copolymers that have been applied for medical devices for long time. Aliphatic diols are common chain extenders(CE) involved in the composition of the hard segments of PCU. However, limited knowledge was discovered about how the chemical structure of CE affects the hydrogen bonding organization within PCUs and their mechanical *** investigate this problem, a group of PCUs were synthesized respectively by extending the polymer chain with 1,4-butanediol(BDO),aminoethanol(MEA), ethanediol(EO) as three kinds of chain extenders. Tiny differences in the CE chemical structure results in remarkable variations in phase separation, condensed morphologies, thermal and mechanical properties, which are characterized by Fourier transform infrared spectrometer, atomic force microscopy, small-angle X-ray scattering, differential scanning calorimetry, and tensile tests. The microstructural evolution during unilateral deformation and the different mechanism induced by the different CEs was probed and unveil by in situ wide-and small-angle X-ray diffraction. Symmetry of CE can improve the organization of the hydrogen bonding. The coherence strength of the urethane/urea group also plays a key role by comparing the two PCUs with ethanediol and aminoethanol.

关键词： Thermoplastic polycarbonate polyurethane Chain extender Hydrogen bonding Mechanical properties

Analytic Formulae for Estimating Motor Proportion of Load Model Under Small Disturbance

在线全文

学校读者我要写书评

暂无评论

CSEE Journal of Power and Energy Systems 2024年第4期10卷 1599-1607页

作者： ping Ju Shiqiu xia Yuqing Jin Lu Cao School of Electrical and Power Engineering Hohai UniversityNanjing 211100China the East China Branch of the State Grid Corporation of China Shanghai 200120China

In the composite load model(CLM),which is commonly used in China,an equivalent motor and equivalent static load are used to represent all electrical equipment and networks connected to a load *** research has determined typical values of electrical and mechanical parameters for load models of different load types,which improves the basis for load ***,the motor proportion parameter is not the same for different load buses or at different times;therefore,obtaining the actual motor proportion is key to establishing an accurate load *** the existing load modeling method,motor proportion is commonly identified along with other parameters under rare large disturbances;therefore,the value of the motor proportion is fixed by the time when a large disturbance *** this paper,formulae are derived to estimate motor proportion under small disturbances,and these formulae allow direct calculation of motor proportion without using any optimization *** proposed estimation formulae do not rely on any parameters of load model or power system but instead rely only on measurement of the voltage and active power at steady-state points before and after a small *** of universality of small disturbances in power systems,estimating time-varying motor proportion under small disturbances will be helpful for solving the time-varying problem of load ***,the proposed motor proportion estimation formulae are validated by simulations,physical experiments,and field experiments.

关键词： Composite load model load modeling motor proportion parameter estimation

Microbiome and intestinal pathophysiology in post-acute sequelae of COVID-19

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Genes & Diseases 2024年第3期11卷 220-231页

作者： Jilei Zhang Yongguo Zhang Yinglin xia jun Sun Division of Gastroenterology and Hepatology Department of MedicineUniversity of Ilinois ChicagoIL60612USA Uic Cancer Center Department of Microbiology and ImmunologyUniversity of Ilinois ChicagoChicagoIL60612USA Jesse Brown VA Medical Center ChicagoIL60612USA

Long CoVID,also known for post-acute sequelae of CovID-19,describes the people who have the signs and symptoms that continue or develop after the acute coviD-19 *** CovID patients suffer from an inflammation or host responses towards the virus approx-imately 4 weeks after initial infection with the SARS CoV-2 virus and continue for an unchar-acterized *** infected with CovID-19 before could experience long-CcovID conditions,including the patients who were infected with SARS CoV-2 virus confirmed by tests and those who never knew they had an infection *** with long CoviD may experience health problems from different types and combinations of symptoms over time,such as fa-tigue,dyspnea,cognitive impairments,and gastrointestinal(Gl)symptoms(e.g.,nausea,vom-iting,diarrhea,decreased or loss of appetite,abdominal pain,and dysgeusia).The critical role of the microbiome in these Gl symptoms and long CovID were reported in clinical patients and experimental ***,we provide an overall view of the critical role of the Gl tract and microbiome in the development of long COVID,including the clinical Gl symptoms in patients,dysbiosis,viral-microbiome interactions,barrier function,and inflammatory bowel disease patients with long *** highlight the potential mechanisms and possible treatment based on Gl health and ***,we discuss challenges and future direction in the long CoVID clinic and research.

关键词： Gastrointestinal symptoms Gl tract Gut microbiome Inflammatorybowel diseases Intestinal barrier Long CoVID Metabolites Tight junctions