检索结果-南通市图书馆

Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

在线全文

学校读者我要写书评

暂无评论

journal of Magnesium and Alloys 2024年第1期12卷 316-331页

作者： h.T.jeong S.w.Lee w.j.Kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul 121-791Republic of Korea

The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy(LAZ1011)with a grain size of 3.2μm,primarily composed of the BCCβphase and a small amount of the hCPαphase,were examined in a temperature range of 473 K to 623 *** microstructural refinement of this alloy was achieved by employing high-ratio differential speed *** best superplasticity was achieved at 523 K and at strain rates of 10^(-4)-5×10^(-4)s^(-1),where tensile elongations of 550±600%were *** the heating and holding stage of the tensile samples prior to tensile loading,a significant increase in grain size was observed at temperatures above 573 ***,it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and *** the investigated strain rate range,the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding,while at high strain rates,lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation *** was concluded that solute drag creep is unlikely to *** the late stages of deformation at 523 K,it was observed that grain boundary sliding led to the agglomeration of theαphase,resulting in significant strain *** mechanism maps were constructed forβ-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate,stress,temperature,and grain size,using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.

关键词： Magnesium-lithium alloy Superplasticity Severe plastic deformation Grain size Grain growth

A hydrodynamic modelling of wave-activated bodies for wavelet marine regions

在线全文

学校读者我要写书评

暂无评论

CLEAN ENERGY 2024年第2期8卷 35-47页

作者： Peh, j. S. Muhieldeen, Mohammed w. Shuaib, N. h. UCSI Univ Fac Engn Technol & Built Environm Mech Engn Dept Kuala Lumpur 56000 Malaysia MTC Engineer Sdn Bhd Shah Alam Selangor Malaysia

Recently, most wave energy research has targeted sea areas with high power density under extreme wave conditions for deployment. This trend often leads to higher energy costs for wave power plants. however, many marine areas with low power density, characterized by wavelet conditions and less destructive forces than extreme wave conditions, remain underexplored. Therefore, this study aimed to propose a wave-activated body model for sea regions with wavelet conditions. The wave-activated body design process encompassed site selection, parameter determination, geometry design, comparison and performance evaluation using the ANSYS (R) AQwA model. The results indicated that the proposed device achieved the desired heave motion, with an amplitude range of 1.2 to -2.5 m, validating its potential for deployment in marine regions with wavelet conditions. Notably, while the proposed design is optimized for wavelet conditions, it was found to have potential limitations in extreme wave environments. This observation emphasizes the challenge of formulating a generalized design suitable for both conditions. Consequently, it is pivotal for wave-activated body designs to be customized based on the specific ocean conditions they target, underscoring the need for specialized designs of wave energy converters that consider the unique wave characteristics of their deployment sites. A wave-activated body is designed for energy generation in ocean regions with wavelet conditions. hydrodynamic modelling is carried out for two locations with different wave characteristics to determine the optimum conditions for deployment. Graphical Abstract

关键词： wave energy converter South China sea renewable and sustainable energy wavelet ANSYS AQwA hydrodynamic wave-activated bodies ENERGY IMPACT

hydromechanical characterization of gas transport amidst uncertainty for underground nuclear explosion detection

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

journal of Rock Mechanics and Geotechnical Engineering 2024年第6期16卷 2019-2032页

作者： wenfeng Li Chelsea w.Neil j william Carey Meng Meng Luke P.Frash Philip h.Stauffer Earth and Environmental Sciences Los Alamos National LaboratoryLos AlamosNM87544USA Department of Mineral Engineering New Mexico TechSocorroNM87801USA

Given the challenge of definitively discriminating between chemical and nuclear explosions using seismic methods alone,surface detection of signature noble gas radioisotopes is considered a positive identification of underground nuclear explosions(UNEs).however,the migration of signature radionuclide gases between the nuclear cavity and surface is not well understood because complex processes are involved,including the generation of complex fracture networks,reactivation of natural fractures and faults,and thermo-hydro-mechanical-chemical(ThMC)coupling of radionuclide gas transport in the *** this study,we provide an experimental investigation of hydro-mechanical(hM)coupling among gas flow,stress states,rock deformation,and rock damage using a unique multi-physics triaxial direct shear rock testing *** testing system also features redundant gas pressure and flow rate measurements,well suited for parameter uncertainty *** porous tuff and tight granite samples that are relevant to historic UNE tests,we measured the Biot effective stress coefficient,rock matrix gas permeability,and fracture gas permeability at a range of pore pressure and stress *** Biot effective stress coefficient varies from 0.69 to 1 for the tuff,whose porosity averages 35.3%±0.7%,while this coefficient varies from 0.51 to 0.78 for the tight granite(porosityhaps an underestimate).Matrix gas permeability is strongly correlated to effective stress for the granite,but not for the porous *** experiments reveal the following key engineering implications on transport of radionuclide gases post a UNE event:(1)The porous tuff shows apparent fracture dilation or compression upon stress changes,which does not necessarily change the gas permeability;(2)The granite fracture permeability shows strong stress sensitivity and is positively related to shear displacement;and(3)hydromechanical coupling among stress states,rock damage,and gas flow appears to be

关键词： Underground nuclear explosion uncertainty quantification Radionuclide transport Biot effective stress coefficient Fracture permeability Matrix permeability

Compressive property and energy absorption characteristic of interconnected porous Mg-Zn-Y alloys with adjusting Y addition

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

journal of Magnesium and Alloys 2024年第1期12卷 171-185页

作者： j.A.Liu S.j.Liu B.wang w.B.Sun X.j.Liu Z.w.han College of Materials Science and Engineering Key Laboratory of Automobile Materials(Ministry of Education)Jilin UniversityChangchun 130022PR China Key Laboratory of Bionic Engineering(Ministry of Education) College of Biological and Agricultural EngineeringJilin UniversityChangchun130022PR China weihai Institute for Bionics-jilin University Weihai 264205PR China

In this study,interconnected porous Mg-2Zn-xY alloys with different phase compositions were prepared by various Y additions(x=0.4,3,and 6 wt.%)to adjust the compressive properties and energy absorption *** characterization methods were then applied to identify the microstructure of the porous Mg-Zn-Y and describe the details of the second *** tests were performed at room temperature(RT),200℃,and 300℃to study the impact of the Y addition and testing temperature on the compressive properties of the porous *** experimental results showed that a high Y content promotes a microstructure refinement and increases the volume fraction of the second *** the Y content increases,different Mg-Zn-Y ternary phases appear:I-phase(Mg_(3)Zn_(6)Y),w-phase(Mg_(3)Zn_(3)Y_(2)),and LPSO phase(Mg_(12)ZnY).when the Y content ranges between 0.4%and 6%,the compressive strength increases from 6.30MPa to 9.23 MPa,and the energy absorption capacity increases from 7.33 Mj/m^(3)to 10.97 Mj/m^(3)at RT,which is mainly attributed to the phase composition and volume fraction of the second ***,the average energy absorption efficiency is independent of the Y *** addition,the compressive deformation behaviors of the porous Mg-Zn-Y are altered by the testing *** compressive strength and energy absorption capacity of the porous Mg-Zn-Y decrease due to the softening effect of the high temperature on the *** deformation behaviors at different temperatures are finally observed to reflect the failure mechanisms of the struts.

关键词： Porous magnesium Rare earth elements Microstructure Compressive behavior Energy absorption characteristic

Convexification of hybrid AC-DC Optimal Power Flow with Line-Commutated Converters

在线全文

学校读者我要写书评

暂无评论

CSEE journal of Power and Energy Systems 2024年第2期10卷 617-628页

作者： hongyuan Liang Zhigang Li j.h.Zheng Q.h.wu School of Electric Power Engineering South China University of TechnologyGuangzhou 510641China

Line-commutated converter (LCC)-based high-voltage DC (hVDC) systems have been integrated with bulk AC power grids for interregional transmission of renewable power. The nonlinear LCC model brings additional nonconvexity to optimal power flow (OPF) of hybrid AC-DC power grids. A convexification method for the LCC station model could address such nonconvexity but has rarely been discussed. we devise an equivalent reformulation for classical LCC station models that facilitates second-order cone convex relaxation for the OPF of LCC-based AC-DC power grids. we also propose sufficient conditions for exactness of convex relaxation with its proof. Equivalence of the proposed LCC station models and properties, exactness, and effectiveness of convex relaxation are verified using four numerical simulations. Simulation results demonstrate a globally optimal solution of the original OPF can be efficiently obtained from relaxed model.

关键词： AC-DC power system convex relaxation linecommutated converter optimal power flow second-order cone programming

Observability Analysis of Integrated Electricity and heating Systems with Thermal Quasi-dynamics in Pipelines

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

CSEE journal of Power and Energy Systems 2024年第3期10卷 1145-1158页

作者： Zhigang Li wenjian Zheng junbo Zhao j.h.Zheng Q.h.wu School of Electric Power Engineering South China University of TechnologyGuangzhou 510641China Fuzhou Changle District Power Supply Company of State Grid Fujian Electric Power Co. Ltd.Fuzhou 350000China Department of Electrical and Computer Engineering University of ConnecticutStorrsCT 06269USA CSEE IEEE

Observability analysis(OA)is vital to obtaining the available input measurements of state estimation(SE)in an integrated electricity and heating system(IEhS).Considering the thermal quasi-dynamics in pipelines,the measurement equations in heating systems are dependent on the estimated results,leading to an interdependency between OA and *** OA methods require measurement equations be known exactly before SE is performed,and they are not applicable to *** bridge this gap,a scenario-based OA scheme for IEhSs is devised that yields reliable analysis results for a predefined set of time-delay scenarios to cope with this *** its core procedure,the observable state identification and observability restoration are formulated in terms of integer linear *** tests are conducted to demonstrate the validity and superiority of the proposed formulation.

关键词： Integrated electricity and heating system measurement observability analysis state estimation thermal quasi-dynamics

Dissociation cross sections ofψ(3770),ψ(4040),ψ(4160),andψ(4415)mesons with nucleons

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Communications in Theoretical Physics 2024年第4期76卷 93-112页

作者： Ruo-Qing Ding Xiao-Ming Xu h j weber Department of Physics Shanghai UniversityBaoshanShanghai 200444China Department of Physics University of VirginiaCharlottesvilleVA 22904United States of America

we study the dissociation of ψ(3770), ψ(4040), ψ(4160), and ψ(4415) mesons in collision with nucleons, which takes place in high-energy proton-nucleus collisions. The quark interchange between a nucleon and a ■ meson leads to the dissociation of the ■ meson. we consider the reactions:■, and■, where R stands for ψ(3770), ψ(4040), ψ(4160), or ψ(4415). A reaction of a neutron and a ■ meson corresponds to a reaction of a proton and the ■ meson by replacing the up quark with the down quark and vice versa. Transition-amplitude formulas are derived from the S-matrix *** cross sections are calculated with the transition amplitudes for scattering in the prior form and in the post form. The cross sections relate to nodes in the radial wave functions of ψ(3770), ψ(4040), ψ(4160), and ψ(4415) mesons.

关键词： inelastic nucleon-charmonium scattering quark interchange relativistic constituent quark potential model

SMILE soft X-ray Imager flight model CCD370 pre-flight device characterisation

在线全文

学校读者我要写书评

暂无评论

Earth and Planetary Physics 2024年第1期8卷 25-38页

作者： S.Parsons D.j.hall O.hetherington T.w.Buggey T.Arnold M.w.j.hubbard A.holland Centre for Electronic Imaging the Open UniversityMilton KeynesMK76AAUK

Throughout the SMILE mission the satellite will be bombarded by radiation which gradually damages the focal plane devices and degrades their *** order to understand the changes of the CCD370s within the soft X-ray Imager,an initial characterisation of the devices has been carried out to give a baseline performance *** CCDs have been characterised,the two flight devices and the flight spa *** has been carried out at the Open University in a bespo ke cleanroom measure ment *** results show that there is a cluster of bright pixels in the flight spa re which increases in size with tempe *** at the nominal ope rating tempe rature(-120℃) it is within the procure ment ***,the devices meet the specifications when ope rating at -120℃ in 6 × 6 binned frame transfer science *** se rial charge transfer inefficiency degrades with temperature in full frame *** any charge losses are recovered when binning/frame transfer is implemented.

关键词： CCD soft X-ray imager characterisation SMILE

On an isotropic porous solid cylinder:the analytical solution and sensitivity analysis of the pressure

在线全文

学校读者我要写书评

暂无评论

Applied Mathematics and Mechanics(English Edition) 2024年第9期45卷 1499-1522页

作者： h.ASGhARI L.MILLER R.PENTA j.MERODIO Departamento de Matematica Aplicada a las TIC ETS de Ingenieria de Sistemas InformaticosUniversidad Politecnica de MadridMadrid 28031Spain School of Mathematics and Statistics University of GlasgowGlasgow G128QQU.K.

within this work,we perform a sensitivity analysis to determine the influence of the material input parameters on the pressure in an isotropic porous solid *** provide a step-by-step guide to obtain the analytical solution for a porous isotropic elastic cylinder in terms of the pressure,stresses,and elastic *** obtain the solution by performing a Laplace transform on the governing equations,which are those of Biot's poroelasticity in cylindrical polar *** enforce radial boundary conditions and obtain the solution in the Laplace transformed domain before reverting back to the time *** sensitivity analysis is then carried out,considering only the derived pressure *** analysis finds that the time t,Biot's modulus M,and Poisson's ratio ν have the highest influence on the pressure whereas the initial value of pressure P_(0) plays a very little role.

关键词： sensitivity analysis Laplace transform cylindrical polar coordinate Biot's modulus cylinder