检索结果-南通市图书馆

Applicability of unique scarf joint configuration in friction stir welding of AA6061-T6:Analysis of torque,force,microstructure and mechanical properties

引用

Defence Technology（防务技术） 2022年第4期18卷 567-582页

作者： Durjyodhan Sethi uttam acharya Shashank Shekhar Barnik Saha Roy Department of Mechanical Engineering National Institute of Technology AgartalaBarjalaJiraniaWest TripuraPin-799046India Department of Materials Science and Engineering Indian Institute of Technology KanpurKanpur208016India

The present research introduces a unique concept of scarf joint technique in friction stir welding(FSW) of aluminum alloy AA 6061-T6 plates and an investigation on weld quality.A new joint configuration with two distinct scarf angles(75°and 60°) was considered in this study.The various aspects of welding were compared with contemporary simple square butt(SSB) joint configuration.Welding was carried out at a constant tool rotation speed(TRS),tool traverse speed(TTS) and tool tilt angle of 1100 rpm,2 mm/s and2°,respectively.The results are analyzed in terms of force and torque distribution,microstructure,macrostructure,and mechanical property perspective for different joint configurations.The study reveals the minimum amount of force and torque at 60°scarf angle joint configuration compared to that of square butt joint configuration.Macro study shows that all the joints were defect-free,and a prominent onion ring was present in the lower portion of the weld nugget(WN).Fine equiaxed grains with a minimum average grain size diameter of 6.82 μm were obtained in the WN of scarf joint configuration(SJC).The maximum ultimate tensile strength(UTS) and maximum average NZ hardness of 267 MPa and83.82 HV0.1were obtained in SJC3 at a scarf angle of 60°.It has been observed from the investigation that the joint efficiency increases from 72.5%(SSB) to 86%(SJC3) at a 60° scarf angle.This unique characteristic may lay an impetus on probable joint strength enhancement technique without increasing the production cost.

关键词： Friction stir welding Joint configuration Al alloys Force and torque Microstructure Mechanical property

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

引用

Defence Technology（防务技术） 2020年第2期16卷 381-391页

作者： uttam acharya Barnik Saha Roy Subhash Chandra Saha Department of Mechanical Engineering National Institute of Technology AgartalaBarjalaJiraniaWest Tripura799046India

This study investigates the effect of tool rotational speed(TRS)on particle distribution in nugget zone(NZ)through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiCp-T6 composite.6 mm thick plates are welded at a constant tool tilt angle of 2°and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm,1500 rpm and 2000 rpm with a taper pin profiled tool.Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ.The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool.The particles occupy maximum area in the matrix compared to that of the base material(BM)due to the redistribution of broken particles as an effect of TRS.The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS(2000 rpm).The microhardness analysis depicts variation in average hardness from top to bottom of the NZ,minimum for 1500 rpm and maximum for 2000 rpm.The impact strength at 1000 rpm and 1500 rpm remains close to that of BM(21.6 J)while 2000 rpm shows the accountable reduction.The maximum joint efficiency has been achieved at 1500 rpm(84%)and minimum at 1000 rpm(68%)under tensile loading.Fractographic analysis shows mixed mode of failure for BM,1000 rpm and 1500 rpm,whereas 2000 rpm shows the brittle mode of failure.

关键词： Friction stir welding Aluminium matrix composite Tool rotational speed Particle distribution Mechanical property

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：