检索结果-南通市图书馆

Precipitation Behavior and Mechanical Properties of a 16Cr-25Ni Superaustenitic Stainless Steel Weld Metal During Post-weld Heat Treatment

引用

Acta Metallurgica Sinica(English Letters) 2022年第4期35卷 577-590页

作者： Wenbin Tian Dong Wu Yiyi Li shanping lu Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China CAS Key Laboratory of Nuclear Materials and Safety Assessment Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China

A 16Cr-25Ni superaustenitic stainless steel weld metal for austenitic stainless steel/ferrite heat-resistance steel dissimilar metal weld was designed and prepared through tungsten inert-gas welding.The precipitate evolution and its correlation with mechanical properties were investigated during post-weld heat treatment(PWHT)at 690℃ for up to 12 h.The primary precipitates in the as-welded weld metal were identified as Mo-rich M6C carbides in the interdendritic region and semicontinuous fine-sized M23C6 carbides along grain boundary.After PWHT,three types of precipitates coexisted in the interdendritic region:primary M6C carbides,newly precipitated Mo-rich M2X carbonitrides and some of the secondary M23C6 carbides.Additionally,mass secondary M23C6 carbides formed and coarsened along grain boundary.No undesirable intermetallic phases formed during the whole period.The M2X and interdendritic M23C6 improved the strength of the weld metal after PWHT,but the elongation and impact toughness degraded,which were mainly owing to the intergranular M23C6 carbides that changed the fracture mode from ductile transgranular mode to mixed mode of transgranular and intergranular fracture.Meanwhile,the coarsening of M2X carbonitrides may lead to the elongation loss during 8 h to 12 h.Evolution of impact toughness was also related to the M2X carbonitrides,which made the crack easier to propagate compared with austenitic matrix and contributed to the decline of impact toughness.However,due to the sluggish precipitation of M2X carbonitrides with longer holding time,the decreasing trend became slow from 4 to 12 h.The results showed that PWHT should be controlled within 8 h to obtain better combination of strength and ductility.

关键词： Superaustenitic stainless steel Weld metal Post-weld heat treatment Precipitate evolution Mechanical properties

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Microstructural evolution and stress relaxation cracking mechanism for Super304H austenitic stainless steel weld metal

引用

Journal of Materials Science & Technology 2022年第5期100卷 82-90页

作者： Xiaopeng Xiao Dianzhong Li Yiyi Li shanping lu Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China Key Laboratory of Nuclear Materials and Safety Assessment Insititute of Metal ResearchChinese Academy of SciencesShenyang 110016China

The pre-compressed CT technique was used to quantitatively investigate the formation of stress relaxation cracks under different tensile residual stresses and aging time in Super304H austenitic stainless steel weld metal.The statistical results revealed that intergranular cracks could occur within 2000 h under 650℃ when the residual stress was applied with greater than 18 KN pre-compression force.Detailed grain interior and boundary analyses showed that the growth of intragranular Cu-rich particles could induce a strong grain interior,and the intergranular Nb(C,N)carbides were one of the causes to crack under short-term aging time.For long-term aging time conditions,the intergranular M_(23)C_(6)carbides were more susceptible to crack than intergranular Nb(C,N)carbides.Finally,the mechanism responsible for stress relaxation cracking formation was carefully illustrated for the weld metals after short-term aging and long-term aging,respectively.

关键词： Stress relaxation cracking Super304H steel Weld metal Aging treatment Residual stress Precipitates

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Active MoS_(2)-based electrode for green ammonia synthesis

引用

Chinese Journal of Chemical Engineering 2024年第1期65卷 268-275页

作者： Xin Liu Lei Yang Tao Wei shanping Liu Beibei Xiao School of Energy and Power Engineering Jiangsu University of Science and TechnologyZhenjiang 212003China Institute Charles Gerhardt Montpellier UMR-5253Universite de MontpellierCNRSENSCMPlace E.Bataillon34095 Montpellier Cedex 05France

Nitrogen electro-reduction under mild conditions is one promising alternative approach of the energyconsuming Haber-Bosch process for the artificial ammonia synthesis.One critical aspect to unlocking this technology is to discover the catalysts with high selectivity and efficiency.In this work,the N_(2)-to-NH_(3)conversion on the functional MoS_(2)is fully investigated by density functional theory calculations since the layered MoS_(2)provides the ideal platform for the elaborating copies of the nitrogenase found in nature,wherein the functionalization is achieved via basal-adsorption,basal-substitution or edge-substitution of transition metal elements.Our results reveal that the edge-functionalization is a feasible strategy for the activity promotion;however,the basal-adsorption and basal-substitution separately suffer from the electrochemical instability and the NRR inefficiency.Specifically,MoS_(2)functionalized via edge W-substitution exhibits an exceptional activity.The energetically favored reaction pathway is through the distal pathway and a limiting potential is less than 0.20 V.Overall,this work escalates the rational design of the high-effective catalysts for nitrogen fixation and provides the explanation why the predicated catalyst have a good performance,paving the guidance for the experiments.

关键词： Nitrogen reduction reaction Density functional theory calculations Molybdenum disulfide Electrochemistry Catalyst Thermodynamics

来源：

维普期刊数据库

同方期刊数据库博看期刊评论

在线全文

学校读者我要写书评

暂无评论

Effects of Stabilization Heat Treatment on Microstructure and Mechanical Properties of Si‑Bearing 15Cr–9Ni–Nb Austenitic Stainless Steel Weld Metal

引用

Acta Metallurgica Sinica(English Letters) 2023年第4期36卷 637-649页

作者： Yakui Chen Dong Wu Dianzhong Li Yiyi Li shanping lu Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China CAS Key Laboratory of Nuclear Materials and Safety Assessment Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China

Two 15Cr–9Ni–Nb austenitic stainless steel weld metals with 2.5%Si and 3.5%Si(namely 2.5Si and 3.5Si samples,respectively)were designed and prepared through tungsten inert gas(TIG)welding and then hold at 800℃ or 900℃ for 3 h for stabilization.The microstructure and mechanical properties were investigated both for the as-welded and after-stabilization heat treatment(SHT)weld metals.There are 3.0–4.0%martensite and 2.5–3.5%δferrite in the 2.5Si as-welded weld metal and 6.0–7.0%δferrite in the 3.5Si as-welded weld metal.After SHT,a large amount of martensite formed in the 2.5Si weld metal,andδ→γtransition occurred during the SHT process both for the 2.5Si and 3.5Si weld metals.There were a large amount of coarse NbC and few nanoscale NbC in the as-welded weld metal.During the SHT,a large amount of nanoscale NbC formed in the matrix,while a large number of G phases formed at the austenite grain boundaries and theδ/γinterfaces.The decrease in solid solution C andδferrite content led to the decline of the yield strength of the weld metal after SHT.The martensite formed in 2.5Si weld metal after SHT had less effect on strength because of its low carbon content.The G phases formed during the SHT reduced the impact energy of the weld metal because it promoted the intergranular fracture,while theδ→γtransition reduced the amount of theδ/γinterfaces and avoided the intergranular fracture,which was beneficial for the impact toughness of the weld metals.

关键词： Austenitic stainless steel Weld metal Stabilization heat treatment Martensite NbC δ→γtransition

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Metal-Free Synthesis of 2-Aminobenzothiazoles via I2-Catalyzed Tandem Cyclization Reaction of Amines and Carbon Disulfide

引用

Chinese Journal of Chemistry 2024年第8期42卷 846-852页

作者： Ting Chen Wei Feng Ruitong Yang shanping Chen Guo-Jun Deng Key Laboratory for Green Organic Synthesis and Application of Hunan Province Key Laboratory of Environmentally Friendly Chemistry and Application of Ministry of EducationCollege of ChemistryXiangtan UniversityXiangtanHunan411105 China School of Chemistry and Chemical Engineering Henan Normal UniversityXinxiangHunan453007 China

Comprehensive Summary,A convenient approach for the construction of 2-aminobenzothiazoles via I2-catalyzed tandem cyclization reaction of amines and carbon disulfide has been developed.The present approach starts from simple and readily available starting materials,affording a series of 2-aminobenzothiazoles in up to 89%yields under metal-free conditions.In this work,C—H/N—H functionalization was achieved and multiple C-hetero bonds were successfully constructed in one pot.

关键词： Sulfur heterocycles C-H functionalization Cyclization Tandem reaction Transition-metal-free Amines lodine N-Heterocycles

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

A Study of Microstructure and Mechanical Properties for the Autogenous Single-Pass Butt Weldment of a Ferritic/Martensitic Steel Using Gas Tungsten Arc Welding

引用

Acta Metallurgica Sinica(English Letters) 2021年第5期34卷 628-638页

作者： Dong Wu Shitong Wei shanping lu CAS Key Laboratory of Nuclear Materials and Safety Assessment Institute of Metal ResearchChinese Academy of SciencesShenyang110016China Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang110016China

A 12%Cr ferritic/martensitic steel,HT-9,has been used as a primary core material for nuclear reactors.The microstructure and mechanical properties of gas tungsten arc butt welded joints of HT-9 in as-welded,and as-tempered conditions have been explored.In as-welded condition,the fusion zone(FZ)contained a fresh martensite matrix with delta(δ)-ferrite.Theδ-ferrite was rich in Cr and depleted in C compared with the matrix.The heat-aff ected zone(HAZ)could be divided into three areas as the distance from the fusion line increased:δ-ferrite/martensite duplex zone,fully recrystallized zone,and partly recrystallized zone.Prior austenitic grains did not coarsen in theδ-ferrite/martensite duplex zone due to the newly nucleatedδ-ferrite grains and incompletely ferritizing(δ-ferrite)during the welding thermal cycle.The weldment microhardness distributed heterogeneously with values above 600 HV_(1.0)in the HAZ and FZ and 250 HV_(1.0)in the base metal(BM).Solute C in the matrix,induced by the dissolution of carbide during the welding process,dominated the microhardness variation.Low toughness was observed in the FZ with a quasi-cleavage fracture tested from-80 to 20℃.The tensile fracture occurred in the relatively soft BM tested from 20 to 600℃.In as-tempered condition(760℃for 1 h),M_(23)C_6-type carbides precipitated within the martensitic laths,the lath boundaries,and theδ-ferrite/martensite interfaces.Moreover,V,Cr,Mo-rich nitrides with very small size also precipitated in theδ-ferrite/martensite interface.The tempering treatment improved the homogenous distribution of weldment hardness significantly.Tensile fracture still occurred in the BM of the weldment specimens tested from 20 to 600℃.The impact toughness improved significantly,but the ductile–brittle transaction temperature was-12℃which was higher than that of the normalized and tempered(N&T)BM.δ-ferrite was considered to be one of the major factors aggravating the impact toughness in the FZ.

关键词： Martensitic stainless steel Gas tungsten arc welding(GTAW) Post-weld heat treatment Microstructure Mechanical properties

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Weld Shape Variation and Electrode Oxidation Behavior under Ar-(Ar-CO_2) Double Shielded GTA Welding

引用

Journal of Materials Science & Technology 2010年第2期26卷 170-176页

作者： shanping lu Hidetoshi Fujii Kiyoshi Nogi Shenyang National Laboratory for Materials Science Institute of Metal Research Chinese Academy of ScienceShenyang 110016 China Joining and welding Research Institute Osaka University Osaka 567-0047 Japan

Double shielded gas tungsten arc welding （GTAW, also known as tungsten inert gas （TIG） welding） of an SUS304 stainless steel with pure inert argon as the inner layer shielding and the At-CO2 or CO2 active gas as the out layer shielding was proposed in this study to investigate its effect on the tungsten electrode protection and the weld shape variation. The experimental results showed that the inner inert argon gas can successfully prevent the outer layer active gas from contacting and oxidizing the tungsten electrode during the welding process. Active gas, carbon dioxide, in the outer layer shielding is decomposed in the arc and dissolves in the liquid pool, which effectively adjusts the active element, oxygen, content in the weld metal. When the weld metal oxygen content is over 70×10-6, the surface-tension induced Marangoni convection changes from outward into inward, and the weld shape varies from a wide shallow one to a narrow deep one. The effect of the inner layer gas flow rate on the weld bead morphology and the weld shape was investigated systematically. The results show that when the flow rate of the inner argon shielding gas is too low, the weld bead is easily oxidized and the weld shape is wide and shallow. A heavy continuous oxide layer on the liquid pool is a barrier to the liquid pool movement.

关键词： Double shielding Weld shape Marangoni convection Gas tungsten arc welding

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of Carbon Content on the Creep Rupture Properties and Microstructure of 316H Weld Metals

引用

Acta Metallurgica Sinica(English Letters) 2021年第7期34卷 986-996页

作者： Langlang Zhao Shitong Wei Dianbao Gao shanping lu Key Laboratory of Nuclear Materials and Safety Assessment Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China School of Materials Science and Engineering University of Science and Technology of ChinaShenyang 110016China Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of SciencesShenyang 110016China Nuclear Power and Petro-Chemical Business Group China First Heavy IndustriesDalian 116113China

Two types of 316 butt welds with carbon contents of 0.016%and 0.062%have been produced using the gas tungsten arc welding process.Theδ-ferrite content decreased from 7.2 to 2.8%in volume as the carbon content increased.The creeprupture strength and creep ductility of the two types of weld metals have been measured at 550℃over the stress range of 290-316 MPa and at 600℃over 230-265 MPa.The microstructure change and precipitation behavior of the weld metals were observed and related to the creep rupture properties.The creep rupture strength of the C2(0.062%C)weld metal was higher than that of the Cl(0.016%C)weld metal at both 550℃and 600℃.At 550℃,as the decrease in the applied stress,the difference of the creep-rupture life between the two weld metals diminished due to the higher depletion rate of carbon by precipitation of M_(23)C_(6) in the C2 weld metal,while at 600℃,the difference enlarged due to the massive precipitation ofσphase and extensive crack formation and propagation alongσ/austenite boundaries in the C1 weld metal.For both the C1 and C2 weld metal,the decrease in ductility was adverse with the transformation percentage and related to products of theδ-ferrite transformation.

关键词： 316 stainless steel weld metal Creep rupture properties δ-ferrite M23C6 σphase

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of Structural Parameters of Double Shielded TIG Torch on the Fusion Zone Profile for 0Cr13Ni5Mo Martensitic Stainless Steel

引用

Journal of Materials Science & Technology 2014年第9期30卷 922-927页

作者： Dongjie Li shanping lu Dianzhong Li Yiyi Li Shenyang National Laboratory for Materials Science Institute of Metal Research Chinese Academy of Sciences

The effects of double shielded TIG （tungsten inert gas） torch＇s structural parameters, including the flow rate ratio between the inner and outer layers of gas and the extended length of the electrode （abbreviated as ELE in this work）, on the fusion zone profile have been investigated for OCrl3NiSMo martensitic stainless steel. Results show that the double shielded TIG process yields relatively high penetration of the weld pool in a broad range of the structural parameters. ELE over 3 mm is too large and causes adverse reactions on the protection of electrode. The outer gas with relatively high flow rate or the outer layer with high oxygen content is conducive to the oxygen dissolved into the arc, which results in the oxidation of the weld pool surface and the electrode tip. The double shielded TIG welded metal was tested and presented good impact property.

关键词： Structural parameters Flow rate Electrode extended length Impact energy

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Principles Giving High Penetration under the Double Shielded TIG Process

引用

Journal of Materials Science & Technology 2014年第2期30卷 172-178页

作者： Dongjie Li shanping lu Dianzhong Li Yiyi Li Shenyang National Laboratory for Materials Science Institute of Metal ResearchChinese Academy of Sciences

A new welding method named double shielded tungsten inert gas （TIG） has been developed to improve the TIG weld penetration. The main principles to increase the weld depth have been discussed. Results show that the critical oxygen content in the weld pool is around 100 × 10 -6 as the temperature coefficient of surface tension changes from negative to positive. The tracer test using pure silver shows that the direction of Marangoni convection changes as the oxygen content increases in the weld pool. The effect of arc constriction on the weld depth has been evaluated on a water-cooled copper plate, and the result indicates that the torch of double shielded can give a more powerful arc. Heavy oxide on the pool surface has undesirable impacts on the increasing of weld depth as the oxygen excessively accumulates in weld pool. It is possible to form chromium oxide in the weld process, while the iron oxide may form as the weld surface exposes to the air after the shielded gas moving away.

关键词： Marangoni convection Penetration Tungsten inert gas （TIG） Arc Oxide

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：