检索结果-南通市图书馆

Acta Oceanologica Sinica 2022年第5期41卷 173-182页

作者： Davood Shariatmadari seyed mostafa siadatmousavi Cyrus Ershadi Civil Engineering Department Faculty of Technology and EngineeringUniversity of HormozganHormozganBandar Abbas***Iran School of Civil Engineering Iran University of Science and TechnologyTehran***Iran

This study focuses on the development of a farm of tidal turbines in the Khuran *** important factors include the location of turbines and their hydrodynamic effects on the environment.A three-dimensional circulation model for the Persian Gulf is employed for the comprehensive evaluation of the tidal energy potential throughout the study *** model is validated by using in situ observations of water level and current *** appropriate potential points for extracting the tidal energy were identified in the Persian Gulf using the model *** Khuran Channel,located in the north of Qeshm Island,was found to be the best place to extract tidal energy inside the Persian *** adding the term of momentum losses to the governing equations,the feedback of extracting energy on the hydrodynamic around Qeshm Island was *** simulation results show that the average daily power production of a tidal farm with 99 turbines for one month is approximately 1.3 *** tidal farm also has a significant impact on the water level inside the Khuran Channel,especially near the tidal farm where these fluctuations exceed 4 *** change in the current speed caused by wake reaches 0.4 m/*** effects were active up to 7 km downstream of the *** current velocity was also estimated to be 1.6 m/s and 2.1 m/s during the spring and ebb tides within the channel,respectively.

关键词： renewable energy tidal energy Khuran Channel tidal horizontal axis turbine turbine farm Delft3D

Assessment of sediment yield using RS and GIS at two sub-basins of Dez Watershed,Iran

在线全文

学校读者我要写书评

暂无评论

International Soil and Water Conservation Research 2016年第3期4卷 199-206页

作者： Hamed Noori seyed mostafa siadatmousavi Barat Mojaradi School of Civil Engineering Iran University of Science&TechnologyNarmakTehran ***Iran

Soil erosion is a serious threat to soil and water resources in semi-arid *** Pacific Southwest Inter Agency Committee(MPSIAC)and Erosion Potential Method(EPM),as two well-known models,have shown their performance in many case *** goal of present study is to assess the efficiency of these methods for estimating the sediments yield and erosion intensity within short-term and longterm timeframes over two sub-basins of Dez watershed,west of *** results showed that the study area can be categorized into slight,moderate,high and very high erosion *** half of the study area is highly susceptible to erosion due to the geological formations and land ***,the longterm(i.e.30 years)sediment yield of 387 and 615(kton)y^(-1) estimated by MPSIAC and EPM models demonstrated the superiority of *** to the measured value of 612(kton)y^(-1),the performance of EPM was *** splitting the dataset into six periods of five years,the sediment yield was predicted in short-term periods by both aforementioned *** segmentation provides the opportunity to evaluate the impact of extreme flooding events on the models *** results showed that both models failed in estimation of sediment load during flood ***,the correlation coefficients for estimating the sediment yield were found to be R=0.93 and R=0.85 for EPM and MPSIAC models respectively,for short-term simulations.

关键词： Soil erosion GIS Remote sensing Modified Pacific South-West Inter Agency Committee method(MPSIAC) Erosion Potential Method(EPM)

Spectral Wave Modeling in Very Shallow Water at Southern Coast of Caspian Sea

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Journal of Marine Science and Application 2018年第1期17卷 140-151页

作者： seyed Masoud Mahmoudof Peyman Badiei seyed mostafa siadatmousavi Vahid Chegini Iranian National Institute for Oceanography and Atmospheric Sciences(INIOAS) Tehran ***Islamic Republic of Iran School of Civil Engineering College of EngineeringUniversity of TehranP.O.Box 11155-4563TehranIran School of Civil Engineering Iran University of Science and TechnologyNarmakTehran ***Iran

This study evaluates the capability of the Simulating WAves Nearshore(SWAN)wave model(version 41.01)in predicting significant wave height and spectral peak energy content for swell waves in very shallow water of surf zone during depth-induced wave breaking and *** model results were compared with field measurements at five nearshore *** results demonstrated that some breaker index formulations were successful for significant wave height prediction in surf ***,an incorrect shape of the energy spectrum and overestimated near spectral peak energy content at shallow water stations were obtained using all of the embedded depth-induced wave breaking formulations in *** dependent breaker index on relative depth(Kpd)formulation,which was successful in predicting near spectral peak energy content,resulted in an average error of 30%.Finally,this formulation was modified to enhance the model performance in reproducing the spectral peak energy content.

关键词： Caspian Sea Shallow water SWAN Spectral peak energy Coastal processes

Seasonal variation of the double diffusion processes at the Strait of Hormuz

在线全文

学校读者我要写书评

暂无评论

Acta Oceanologica Sinica 2017年第1期36卷 26-34页

作者： AZIZPOUR Jafar CHEGINI Vahid siadatmousavi seyed mostafa Iranian National Institute for Oceanography and Atmospheric Science Tehran ***Iran Iran University of Science and Technology Tehran ***Iran

Profiles of salinity and temperature were measured in the strait of Hormuz（SH） during the winter of 2012, spring and summer of 2013. To investigate the double diffusion（DD） processes, Turner（TU） angle values are calculated in all the stations in the SH. Different TU angle values correspond to salt fingering（SF）, diffusive convection（DC）and stable stratification. The distributions of the two forms of DD were plotted vertically along transects in the eastern, central and western part of the SH, and corresponding DD processes were described. The results show that both SF and DC occurred in most part of the study area. Two different water masses（the Indian Ocean surface water and the Persian Gulf water） were evident at the SH, and SF and DC were evident at the interface of two water masses. Due to evaporation, SF occurred in the surface layer of most Stations throughout the year. In the eastern part of the SH, occurrences of DC were more feasible in wintertime. SF was the main phenomenon at the end of hot season. For central part, SF occurred throughout the year in water column. In the western part,water column was stable in summer and DC happened in most part of water column in winter.

关键词： double diffusion diffusive convection salt fingering Turner angle Strait of Hormuz

Electrodeposition of nanostructured Ti/(Ru+Ti+Ce)O_2 coatings

在线全文

学校读者我要写书评

暂无评论

Rare Metals 2018年第1期37卷 13-20页

作者： seyed mostafa Peyghambari Mardali Yousefpour Faculty of Materials and Metallurgical Engineering Semnan University

A nanostructured ternary coating of Ti/（Ru ＋ Ti ＋ Ce）O2 was prepared by the conventional electrodeposition on the titanium substrate as the cathode with different numbers of coating layers. The main objective of this work was to study nanostructured coatings of ceramic materials. For this purpose, the amount of precursor materials in the electrolyte was a variable parameter. Furthermore, the salt of TiCl4/RuCl3·xH2 O/Ce（NO3）3·6 H2 O with different amounts, hydrogen peroxide, methanol, and distilled water were used as an aqueousunaqueous bath. In addition, the coated samples were put to heat at 300, 450, 650, and 850℃ in an electric furnace for1 h. The crystalline phase of the coating was characterized by X-ray diffraction（XRD）. The chemical composition and microstructure of the coating were studied using energydispersive spectroscopy（EDS） and scanning electron microscopy analysis（SEM）. Moreover, the electrochemical measurement of Ti/（Ru ＋ Ti ＋ Ce）O2 coatings was carried out. Results show that with the increase in the number of coating layers, the quality of morphology is ***, the best quality of coatings is obtained at six layers on the titanium substrate with electrolyte including TiO2/RuO2/CeO2 with the molar ratio of 70：5：25 after heat treatment at 450 ℃ for 1 h. Besides,with the increase in Ce02 content from 5 wt% to 25 wt% and the number of coating layers, higher thickness of about（20.0±0.1） μm and minimum over potential for chlorine evolution were obtained.

关键词： Oxides Coating Heat treatment Interface Thin films

Experimental and numerical analysis of beam to column joints in steel structures

在线全文

学校读者我要写书评

暂无评论

Frontiers of Structural and Civil Engineering 2018年第4期12卷 642-661页

作者： Gholamreza ABDOLLAHZADEH seyed mostafa SHABANIAN Faculty of Civil Engineering Babol Noshirvani University of TechnologyBabolIran

The behaviors such as extreme non-elastic response, constant changes in roughness and resistance, as well as formability under extreme loads such as earthquakes are the primary challenges in the modeling of beam-to-column connections. In this research, two modeling methods including mechanical and neural network methods have been presented in order to model the complex hysteresis behavior of beam-to-column connections with flange plate. First, the component-based mechanical model will be introduced in which every source of transformation has been shown only with geometrical and material properties. This is followed by the investigation of a neural network method for direct extraction of information out of experimental data. For the validation of behavioral curves as well as training of the neural network, the experiments were carried out on samples with real dimensions of beam-to-column connections with flange plate in the laboratory. At the end, the combinational modeling framework is presented. The comparisons reveal that the combinational modeling is able to display the complex narrowed hysteresis behavior of the beam-to-column connections with flange plate. This model has also been successfully employed for the prediction of the behavior of a newly designed connection.

关键词： beam to column connections experiments component method neural network model combinational modeling

Droplets diameter distribution using maximum entropy formulation combined with a new energy-based sub-model

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Chinese Journal of Chemical Engineering 2016年第11期24卷 1625-1630页

作者： seyed mostafa Hosseinalipour Hadiseh Karimaei Ehsan Movahednejad Energy and Environmental Lab Dpt Mech. Eng. Iran University of Science and Technology 16846-13114 Narmak Tehran lran University of California Berkeley USA

The maximum entropy principle(MEP) is one of the first methods which have been used to predict droplet size and velocity distributions of liquid sprays. This method needs a mean droplets diameter as an input to predict the droplet size distribution. This paper presents a new sub-model based on the deterministic aspects of liquid atomization process independent of the experimental data to provide the mean droplets diameter for using in the maximum entropy formulation(MEF). For this purpose, a theoretical model based on the approach of energy conservation law entitled energy-based model(EBM) is presented. Based on this approach, atomization occurs due to the kinetic energy loss. Prediction of the combined model(MEF/EBM) is in good agreement with the available experimental data. The energy-based model can be used as a fast and reliable enough model to obtain a good estimation of the mean droplets diameter of a spray and the combined model(MEF/EBM) can be used to well predict the droplet size distribution at the primary breakup.

关键词： Mean droplets diameter Energy conservation Maximum entropy formulation (MEF) Size distribution Statistical thermodynamics Mathematical modeling

An agent-based simulation with NetLogo platform to evaluate forward osmosis process(PRO Mode)

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Chemical Engineering 2018年第12期26卷 2487-2494页

作者： mostafa Taherian seyed Mahmoud Mousavi Hooman Chamani Chemical Engineering Department Faculty of Engineering Ferdowsi University of Mashhad Research Center of Membrane Processes and Membrane Faculty of Engineering Ferdowsi University of Mashhad

Forward osmosis(FO), as an emerging technology, is influenced by different factors such as operating conditions,module characteristics, and membrane properties. The general aim of this study was to develop a suitable(flexible,comprehensive, and convenient to use) computational tool which is able to simulate osmosis through an asymmetric membrane oriented in pressure retarded osmosis(PRO) mode in a wide variety of scenarios. For this purpose, an agent-based model was created in NetLogo platform, which is an easy-to-use application environment with graphical visualization abilities and well suited for modeling a complex system evolving over time. The simulation results were validated with empirical data obtained from literature and a great agreement was observed. The effect of various parameters on process performance was investigated in terms of temperature,cross-flow velocity, length of the module, pure water permeability coefficient, and structural parameter of the membrane. Results demonstrated that the increase in all parameters, except structural parameter of the membrane and the length of module led to the increase of average water flux. Moreover, nine different draw solutes were selected in order to assess the influence of net bulk osmotic pressure difference between the draw solution(DS) and feed solution(FS)(known as the driving force of FO process) on water flux. Based on the findings of this paper, the performance of FO process(PRO mode) can be efficiently evaluated using the NetL ogo platform.

关键词： Agent-based model Forward osmosis (PRO mode) Membranes Net Logo platform Simulation Water flux

Flow-mode synthesis of biodiesel under simultaneous microwave–magnetic irradiation

在线全文

学校读者我要写书评

暂无评论

Chinese Journal of Chemical Engineering 2019年第10期27卷 2551-2559页

作者： Behzad Khedri mostafa mostafaei seyed Mohammad Safieddin Ardebili Mechanics of Biosystems Engineering Department Razi UniversityKermanshahIran Biosystems Engineering Department Shahid Chamran University of AhvazAhvazIran

In this study,aiming at optimization of a novel continuous biodiesel production system was developed by combining technologies based on microwaves and magnetic *** affecting microwave-assisted biodiesel(alkyl esters)production reaction were analyzed in this *** factors included magnetic field intensity(0,0.225 and 0.450 T),microwave power(400,821,and 1181 W),percentages of KOH and Na OH catalysts at constant concentrations of 1 wt%(0,50%and 100%),and percentages of ethanol and methanol at a constant molar ratio of 6:1(0,50%and 100%).Response Surface Methodology(RSM)was used to optimize the reaction ***-based analysis indicated that,all independent parameters had significant effects on the reaction *** of the investigations reveal that the largest effects on the conversion efficiency were due to type of alcohol and magnetic field *** optimized conditions were found to be a magnetic field intensity of 0.331 T,a microwave power of 677.77 W,catalyst percentages of 30.35%and 69.65%for KOH and Na OH,respectively,and alcohol percentages of 80.47%and 19.53%for methanol and ethanol,*** the optimal conditions,yield of the reaction was 96.2%.

关键词： Biodiesel Microwave Magnetic field Transesterification Waste cooking oil

Microstructure Modification of Powder Compact of Al-Zn-Mg Nanostructured Alloy by a Semisolid Thermomechanical Processing

在线全文

学校读者我要写书评

暂无评论

Acta Metallurgica Sinica(English Letters) 2016年第1期29卷 39-45页

作者： Mohsen Hajizamani mostafa Alizadeh seyed Ahmad Jenabali-Jahromi Department of Metals Institute of Science and High Technology and Environmental SciencesGraduate University of Advanced Technology Department of Materials Science and Engineering School of EngineeringShiraz University

A thermomechanical process （TMP） consisting of three cycles of cold pressing at 154 MPa and liquid-phase sintering at 600 ℃ for 30 min in each cycle was applied to modify the microstructure of nanostructured A1-Zn-Mg alloy. The alloy powders were produced by mechanical alloying. Also, solid-state sintering at 550℃ for 90 min was done to compare the results with those obtained from the TMP. The powders and the thermomechanically （TM） processed samples were analyzed by XRD to reveal the present phases in addition to calculating the crystallite size changes by the Wil- liamson-Hall method. Moreover, scanning electron microscope was employed to observe the morphology of the powder and the microstructures of the sintered and the TM processed samples. The results revealed that the TMP affected the microstructure noticeably as well as the microhardness by removing the continuous grain boundary porosities and uniform distribution of the intermetallic phase particles as well as obtaining a near globular microstructure after the second cycle. Also, the average grain sizes in the first and the second cycles of the TMP were lower than those of the sintered sample. Furthermore, nanocrystalline grains were stable up to the second cycle of the TMP.

关键词： Thermomechanical processing AI-Zn-Mg alloy Intermetallics Sintering Grain growth