检索结果-南通市图书馆

Numerical investigation of the effect of transitory strand opening on mixing in a multistrand tundish

International Journal of Minerals,Metallurgy and Materials 2011年第5期18卷 535-542页

作者： Sabin Kumar Mishra Pradeep Kumar Jha satish chandra sharma satish Kumar Ajmani Department of Mechanical and Industrial Engineering Indian Institute of Technology RoorkeeRoorkee 247667UttarakhandIndia Steelmaking and Casting Research Group Tata SteelR&DBurma MinesJamshedpur 831007JharkhandIndia

In a multistrand,the outlet near the inlet produces short circuiting *** leads to the formation of dead zones inside the tundish,and consequently,the mean residence time *** the present study,numerical investigation of mixing inside a delta shaped tundish with sloping boundaries was carried out by solving the Navier-Stokes equation and employing the standard turbulence *** decrease the dead zone volume inside the tundish,the effect of closing the outlet near the inlet for a small amount of time and further opening it on the mixing behavior of the tundish was *** outlets near the inlet were closed for varying amount of time,and the transient analysis of fluid flow and the tracer dispersion study were carried out to find the mixing parameters of the tundish,namely,mean residence time and the ratio of mixed to dead volume of the *** optimum closure time of the near outlet has been found,which yields best mixing inside the *** numerical code was validated against the experimental observation by performing the tracer dispersion study inside a multistrand tundish and the reasonably good match between the experimental and numerical results in terms of residence time distribution （RTD） *** results obtained from the present study confirm the strong role of choosing the right time for opening and closing the outlets to get improved characteristics for the fluid flow and mixing behavior of the *** educational version of computational fluid dynamics （CFD） software PHOENICS was used to solve the governing equations and interpret the results in different forms.

关键词： continuous casting billets tundish flow simulation mean residence time dead volume computational fluid dynamics (CFD)

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Review of Finger millet(Eleusine coracana(L.)Gaertn):A power house of health benefiting nutrients

引用

Food Science and Human Wellness 2016年第3期5卷 149-155页

作者： Dinesh chandra satish chandra Pallavi A.K.sharma Department of Biological Sciences Govind Ballabh Pant University of Agriculture and Technology Pantnagar263145UttarakhandIndia

The bulk of the world’s millet crop is produced by India,Nigeria,Niger,Mali,Burkina Faso,Chad,and *** millet(Eleusine coracana(L.)Gaertn),little millet(Panicum sumatrense Roth ex Roem.&Schult.),foxtail millet(Setaria italica(L.)***)and proso millet(Panicum miliaceum L.)are most commonly found species among various millet *** India,finger millet occupy the largest area under cultivation among the small *** millet stands unique among the cereals such as barley,rye and oats with higher nutritional contents and has outstanding properties as a subsistence food *** is rich in calcium(0.34%),dietary fiber(18%),phytates(0.48%),protein(6%–13%)minerals(2.5%–3.5%),and phenolics(0.3%–3%).Moreover,it is also a rich source of thiamine,riboflavin,iron,methionine,isoleucine,leucine,phenylalanine and other essential amino *** abundance of these phytochemicals enhances the nutraceutical potential of finger millet,making it a powerhouse of health benefiting *** has distinguished health beneficial properties,such as anti-diabetic(type 2 diabetes mellitus),anti-diarrheal,antiulcer,anti-inflammatory,antitumerogenic(K562 chronic myeloid leukemia),atherosclerogenic effects,antimicrobial and antioxidant properties.

关键词： power benefit occupy

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Fabrication of Self-cleaning Antireflective Polymer Surfaces by Mimicking Underside Leaf Hierarchical Surface Structures

引用

Journal of Bionic Engineering 2019年第3期16卷 400-409页

作者： Srinadh Mattaparthi chandra Shekhar sharma Creative & Advanced Research Based on Nanomaterials (CARBON) Laboratory Department of Chemical Engineerings Indian Institute of Technology Hyderabad Kandi Telangana 502285 India

In this work, we utilized underside of four different plant leaves with different scale of hierarchical surface roughness to fabricate large area self-cleaning antireflective polymer surfaces. A simple and precise two-step soft-lithography replica molding technique was deployed by using polydimethylsiloxane (PDMS) polymer as a replicating material. In the first step, a negative PDMS replica was fabricated by using the underside of an original leaf as a template material. In the second step, a positive PDMS replica was fabricated through a negative PDMS replica used as a template. In order to study the non-wetting and light trapping properties, as-replicated polymer surfaces were characterized using Scanning Electron Microscopy (SEM), contact angle goniometer, and UV-Vis spectroscopy. SEM images confirmed the successful replication of complex hierarchical structures while contact angle measurement studies established retaining high non-wetting properties in polymer replicas. Optical studies suggest near zero reflection in normal mode and less than 5% diffuse reflection when measured using integrated sphere mode. These results have been correlated and explained with the air-liquid fraction and roughness factor as measured using three-dimensional optical profilometer.

关键词： biomimicking natural leaf replica molding non-wetting light trapping hierarchical roughness

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Dynamics of fine root N,Pand K in high elevation forests of central Himalaya

引用

Forestry Studies in China 2012年第2期14卷 145-151页

作者： satish chandra GARKOTI School of Environmental Sciences Jawaharlal Nehru University

Fine root nutrient dynamics were calculated for one year in three high elevation forests of Indian central Himalaya. In all sites, fine root nutrient concentrations varied with respect to forests and seasons. N concentration in fine roots was highest followed by K and P. In general, fine roots showed their highest nutrient concentrations during the rainy season and lowest in winter. Higher nutrient concentrations during the rainy season may be related to favorable moisture and temperature regimes which in turn results in increased plant growth activities. Present fine root nutrient amounts and nutrient uptake values decreased towards high elevations. In general, the highest amounts of nutrients in both live and dead fine roots were observed in September and the lowest in the month of June. Turnover rates of the nutrients in the fine roots also decreased with an increase in elevation.

关键词： cappadocian maple Himalayan birch bell rhododendron nutrient concentration nutrient uptake

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of cooling media on bead geometry,microstructure,and mechanical properties of wire arc additive manufactured IN718 alloy

引用

Advances in Manufacturing 2024年第1期12卷 124-149页

作者： Parveen Kumar satish Kumar sharma Ratnesh Kumar Raj Singh Department of Mechanical Engineering Thapar Institute of Engineering and TechnologyPatialaPunjab147004India

This work aims to present and explore thermal management techniques for the wire arc additive manufacturing(WAAM)of IN718 *** heat can be mitigated via air or water *** this study,the material was deposited under four different heat-input conditions with air or water *** air cooling,the layer is deposited in a normal atmospheric air environment,whereas with water cooling,the material is deposited inside a water tank by varying the water *** validate the air and water cooling thermal management techniques,IN718 single-pass and multilayer linear walls were deposited using the bidirectional gas metal arc welding based WAAM setup under four different heat input *** the deposition of single layers,the temperature profiles were recorded,and the geometric and microstructural features were *** multilayer wall structures,the mechanical properties(hardness,tensile strength,and elongation)were determined and assessed using the corresponding microstructural features explored through scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),and electron backscatter diffraction(EBSD)*** microstructure observed through SEM analysis in the building direction was found to be nonhomogenous compared with that in the deposition ***,water cooling was found to govern bead characteristics,such as wall width and *** grain size and anisotropy of the mechanical properties also decreased in the water-cooled ***,water cooling is an economical and efficient method to mitigate excessive heat accumulation in WAAM-deposited IN718.

关键词： Air cooling Water cooling IN718 Bead characteristics Microstructure Electron backscatter diffraction(EBSD)

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Ethanol steam reforming study over ZSM-5 supported cobalt versus nickel catalyst for renewable hydrogen generation

引用

Chinese Journal of Chemical Engineering 2019年第3期27卷 677-684页

作者： Ashutosh Kumar Ram Prasad Yogesh chandra sharma Department of Chemistry Indian Institute of Technology (Banaras Hindu University) Varanasi Department of Chemical Engineering & Technology Indian Institute of Technology (Banaras Hindu University) Varanasi

The renewable hydrogen generation through ethanol steam reforming is one of the anticipated areas for sustainable hydrogen generation. To elucidate the role of Ni and Co with ZSM-5 support, catalysts were prepared by wet impregnation method and ethanol steam reforming(ESR) was performed. The catalysts were characterized by HR-XRD, ATR–FTIR, HR-SEM, TEM with SAED, EDAX, surface area analyzer and TPR. It had shown complete ethanol conversion at 773 K, but the selectivity in hydrogen generation was found higher for 10% Ni/ZSM-5 catalyst as compared to 10% Co/ZSM-5. The 10% Ni/ZSM-5 catalyst has about 72% hydrogen selectivity at temperature 873 K. It indicates that Ni is a more sustainable catalyst as compared to Co with ZSM-5 support for ESR. The C_2H_4 was found major undesirable products up to 823 K temperature. Nevertheless, the 10% Ni/ZSM-5 catalyst had shown its stability for high temperature(873 K) ESR performance.

关键词： Ethanol steam reforming Zeolite Hydrogen Renewable energy Catalyst

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Some Observations about the MOLSCAT

引用

Communications in Theoretical Physics 2015年第12期64卷 731-734页

作者： Mohit Kumar sharma Monika sharma Suresh chandra School of Studies in Physics Jiwaji University Physics Department Lovely Professional University

For calculation of cross sections for collisional transitions between rotational levels in a molecule,a computer code,MOLSCAT is *** the transitions between rotational levels in H_2 CS due to collisions with He atom,we have calculated cross sections under the CS approximation,for example,for total energy 11 cm^(-1).The calculations have been done for the single energy 11 cm"1 and for ten *** have found that the cross sections for the single energy 11 cm^(-1),differ from those in the first seven combinations,but are in agreement with those in the last three *** reason for the difference in the results appears that the MOLSCAT uses the intermediate data of calculations for one energy,in the calculations for other *** agreement with the last three combinations may be understood that when the energy of combination is in the decreasing trend,the cross sections for the first(common)energy are *** may be suggested to run the MOLSCAT for a single energy at a time.

关键词： ISM: molecules collisional transitions MOLSCAT

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Queue clearance rate method for estimating passenger car equivalents at signalized intersections

引用

Journal of Traffic and Transportation Engineering(English Edition) 2017年第5期4卷 487-495页

作者： Mithun Mohan satish chandra Department of Civil Engineering Indian Institute of Technology RoorkeeRoorkee 247667India Central Road Research Institute New Delhi 110025India

This study explored the use of queue clearance rate method for estimating passenger car equivalent （PCE） at signalized intersections. PCE was estimated based on the assumption that the rate at which a queue of vehicles clears the intersection is a function of its composition. Results of this method were compared with the results estimated by some popular techniques. A fourqegged intersection was simulated in VISSIM software and different techniques were used to convert the traffic mix into a uniform one. Parameters of VISSIM were modified to closely reflect the traffic behaviour under heterogeneous traffic conditions. All approaches of the intersection were loaded to saturated conditions and accuracy of estimated PCEs were established by comparing converted flow （PCE/h） with the capacity of an all-car traffic stream. Method based on saturation flow delivered the best result, but its use was limited to traffic composed only of two types of vehicles. Results of regression and optimization techniques were almost similar and the converted flow was close to the capacity of all-car stream. However, accuracy of these methods strongly relied on the correct measurement of saturation flow. Queue clearance rate method did not require value of saturation flow and yielded good estimates of PCE throughout the simu- lation runs. The maximum difference between the converted flow and capacity estimated with all car situations was found to be less than 10% in all cases considered in this study.

关键词： Passenger car equivalents Signalized intersection Queue clearance rate method Simulation VISSIM

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Wind pollination in Pinus roxburghii

引用

Progress in Natural Science:Materials International 2007年第1期17卷 32-38页

作者： Vinod Prasad KHANDURI chandra Mohan sharma Department of Forestry Mizoram University Aizawl(Mizoram)India Department of Forestry HNB Garhwal University Srinagar Garhwal-246 174(Uttaranchal)India

Stigmatic pollen load and pollen concentration in the air were studied in the natural population of Pinus roxburghii at Ashtavakra (900 m asl), in the Pauri forest division of Garhwal Himalaya, India. The results reflect diurnal pollen occurrence in P. roxburghii , with the strong significant correlations between pollen concentrations in the air and wind speed, air temperature and relative air humidity. A significant correlation was also observed between microsporangium dehiscence and pollen occurrence in the air. The maximum concentration of pollen grains in the air and higher rates of pollen deposition onto the megasporophylls were between 12 pm and 16 pm of the day, which conforms the best time for pollination in a day in P. roxburghii. The receptivity of Ovulate strobili varied from 3 to 5 days, however, the bagged strobili remained receptive up to 6 days.

关键词： ovulate strobili pollen cones pollination receptivity wind speed P. roxburghii.

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

MOLECULAR DYNAMICS SIMULATION OF POLYMER/CARBON NANOTUBE COMPOSITES

引用

Acta Mechanica Solida Sinica 2015年第4期28卷 409-419页

作者： Sumit sharma Rakesh chandra Pramod Kumar Navin Kumar Department of Mechanical Engineering Dr.B.R.Ambedkar National Institute of Technology School of Mechanical Materials & Energy Engineering (SMMEE) Indian Institute of Technology

In this paper, we present classical molecular dynamics （MD） simulations of model polymer/CNT composites constructed by embedding a single wall （10,10） CNT into two different amorphous polymer matrices： poly（methyl methacrylate） and poly{（m-phenylene-vinylene）-co- [（2,5-dioctoxy-p-phenylene） vinylene]}, respectively, with different volume fractions. The simulation results support the idea that it is possible to use CNTs to mechanically reinforce an appropri- ate polymer matrix, especially in the longitudinal direction of the nanotube. The comparison of the simulation results with the macroscopic rule-of-mixtures for composite systems showed that for strong interfacial interactions, there can be large deviations of the results from the rule-of- mixtures. In order to verify this study, results obtained have been compared with those given by Elliott and Han （2007）.

关键词： nano-structures elasticity mechanical properties computational modeling

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：