检索结果-南通市图书馆

Mechanical performance of 22SiMn2TiB steel welded with lowtransformation- temperature filler wire and stainless steel filler wire

引用

Journal of Iron and Steel Research International 2024年第4期31卷 967-981页

作者： zi-dong Lin Kai-jie Song Zhen Sun zi-qian Zhu Xue-feng Zhao Constantinos Goulas Wei Ya Xing-hua Yu School of Materials Science and Engineering Beijing Institute of TechnologyBeijing 100081China Beijing Institute of Technology Chongqing Innovation Center Chongqing 401120China Department of Design Production and Management Faculty of Engineering Technology.University of TwenteEnschede 7500 AETheNetherlands Rotterdam Additive Manufacture Fieldlab(RAMLAB) Rotterdam 3089 JWTheNetherlands

TX-80 low-transformation-temperature(LTT)welding wire was used to replace the traditional ER 307Si welding wire to realize the connection of 22SiMn2TiB armor steel in manual overlay *** previously existing issues,such as welding cracks,large welding deformation,and severe welding residual stress,were solved to ensure good strength and ductility *** particular,with the same welding conditions,TX-80 LTT wire eliminates welding *** reduces the welding deformation no matter the base pretreatment of pre-setting angle or no pre-setting *** comparison,it was found that the microstructure at the TX-80 weld is mainly composed of martensite and a small amount of retained *** contrast,the microstructure of the ER 307Si weld consists of a large amount of austenite and a small amount of skeleton-like *** variation trend of residual stress and microhardness from the weld to the base were investigated and compared with the mechanical properties of base *** TX-80 and the ER 307Si tensile samples elongation is 6.76%and 6.01%,while the ultimate tensile strengths are 877 and 667 MPa,*** average impact toughness at room temperature of the ER 307Si weld is 143.9 J/cm^(2),much higher than that of the TX-80 weld,which is only 36.7 J/cm^(2).The relationship between impact and tensile properties with microstructure species and distribution was *** addition,the fracture surface of the tensile and the impact samples was observed and *** dimples,fewer pores,larger radiation zone,and shear lips of TX-80 samples indicate better tensile ductility and worse impact toughness than those of ER 307Si weld.

关键词： Low-transformation-temperature material 22SiMn2TiB steel Welding deformation Residual stress Martensitic transformation Mechanical property

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Hydrophobic tag tethering degrader as a promising paradigm of protein degradation:Past,present and future perspectives

引用

Chinese Chemical Letters 2024年第8期35卷 187-200页

作者： Si Ha Jiacheng Zhu hua Xiang Guoshun luo State Key Laboratory of Natural Medicines and Department of Medicinal Chemistry China Pharmaceutical UniversityNanjing 211198China

Small molecule inhibitors have dominated the pharmaceutical landscape for a long time as the primary therapeutic paradigm targeting pathogenic ***,their efficacy heavily relies on the amino acid composition and spatial constitution of proteins,rendering them susceptible to drug resistance and failing to target undruggable *** recent years,the advent of targeted protein degradation(TPD)technology has captured substantial attention from both industry and *** an event-driven mode,TPD offers a novel approach to eliminate pathogenic proteins by promoting their degrada-tion,thus circumventing the limitations associated with traditional small molecule ***-bic tag tethering degrader(HyTTD)technology represents one such TPD approach that is currently in the burgeoning *** employ endogenous protein degradation systems to induce the degrada-tion of target proteins through the proteasome pathway,which displays significant potential for medical *** this review,we provide a comprehensive overview of the development history and the reported mechanism of action of ***,we delve into the physiological roles,structure-activity re-lationships,and medical implications of HyTTDs targeting various disease-associated ***,we propose insights into the challenges that necessitate resolution for the successful development of HyTTDs,with the ultimate goal of initiating a new age of clinical treatment leveraging the immense po-tential of HyTTDs.

关键词： Targeted protein degradation(TPD) Hydrophobic tag Degrader Hydrophobic tag tethering degrader(HyTTD) Targeted therapy

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Preparation of PVA/GO/h-BN Janus Film with High Thermal Conductivity and Excellent Flexibility via a Density Deposition Self-assembly Method

引用

Chinese Journal of Polymer Science 2024年第8期42卷 1217-1226页

作者： Fang-hua luo Zhi-Tao Dong Guo-hua Chen Chen Ma huai-Yuan Wang College of Chemistry and Chemical Engineering Northeast Petroleum UniversityDaqing 163318China College of Materials Science and Engineering Huaqiao UniversityXiamen 361000China School of Chemical Engineering and Technology and State Key Laboratory for Chemical Engineering Tianjin UniversityTianjin 300350China

Janus films with asymmetric physical/chemical properties have attracted con siderable attention due to their promising applications in personal thermal management,electronic skin s,sensors,actuators,***,traditional methods for fabricating Janus films conventionally need the assistance of an interface or auxiliary equipment,which are usually complex and ***,flexible poly(vinyl alcohol)(PVA)/graphene oxide(GO)/h-BN(recorded as PVA/GO/h-BN)Janus films with thermally,optically,and electrically anisotropic properties are fabricated by a simple density deposition self-assem bly method,which just utilizes the density difference between GO and h-BN during water *** results show that the two sides of the acquired Janus films have obvious asymmetric *** the original state of the PVA/GO/h-BN Janus films,the thermal conductivity of the GO side(10.06 W·m^(-1)·K^(-1))is generally lower than that of the h-BN side(10.48W·m^(-1)·K^(-1)).But after GO is reduced,the thermal conductivity of the rGO side reaches 12.17 W·m^(-1)·K^(-1),surpassing that of the h-BN *** addition,the relative reflectance of the h-BN side of Janus film is also significantly higher than that of the rGO side,and the su rface resistance difference between the two sides is about 4 orders of *** prepared PVA/GO/h-BN Janus films show great application potential in human thermal management,light conversion switches,and electronic *** study provides a simple and versatile strategy for fabricating Janus films with multifunctional(such as thermal,optical,and electrical)anisotropies.

关键词： Janus films PVA/GO/h-BN Density deposition self-assembly method

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Impact of metabolic syndrome components on clinical outcomes in hypertriglyceridemia-induced acute pancreatitis

引用

World Journal of Gastroenterology 2024年第35期30卷 3996-4010页

作者： Zhen-hua Fu zi-Yue Zhao Yao-Bing Liang Dong-Yu Cheng Jian-Ming luo Hai-Xing Jiang Shan-Yu Qin Department of Gastroenterology The First Affiliated Hospital of Guangxi Medical UniversityNanning 530021Guangxi Zhuang Autonomous RegionChina

BACKGROUND The incidence of hypertriglyceridemia(HTG)-induced acute pancreatitis(AP)is steadily increasing in China,becoming the second leading cause of *** complications and outcomes associated with HTG-AP are generally more severe than those seen in AP caused by other ***-AP is closely linked to metabolic dysfunction and frequently coexists with metabolic syndrome or its ***,the impact of metabolic syndrome components on HTGAP clinical outcomes remains *** To investigate the impact of metabolic syndrome component burden on clinical outcomes in *** In this retrospective study of 255 patients diagnosed with HTG-AP at the First Affiliated Hospital of Guangxi Medical University,we collected data on patient demographics,clinical scores,complications,and clinical ***,we analyzed the influence of the presence and number of individual metabolic syndrome components,including obesity,hyperglycemia,hypertension,and low high-density lipoprotein cholesterol(HDL-C),on the aforementioned parameters in HTG-AP *** This study found that metabolic syndrome components were associated with an increased risk of various complications in HTG-AP,with low HDL-C being the most significant risk factor for clinical *** risk of complications increased with the number of metabolic syndrome *** for age and sex,patients with highcomponent metabolic syndrome had significantly higher risks of renal failure[odds ratio(OR)=3.02,95%CI:1.12-8.11)],SAP(OR=5.05,95%CI:2.04-12.49),and intensive care unit admission(OR=6.41,95%CI:2.42-16.97)compared to those without metabolic *** The coexistence of multiple metabolic syndrome components can synergistically worsen the clinical course of HTGAP,making it crucial to monitor these components for effective disease management.

关键词： Hypertriglyceridemia-induced acute pancreatitis Metabolic syndrome High density lipoprotein cholesterol Obesity Hyperglycemia Hypertension Clinical outcomes

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Micro segment analysis of supercritical methane thermal-hydraulic performance and pseudo-boiling in a PCHE straight channel

引用

Petroleum Science 2024年第2期21卷 1275-1289页

作者： Qian Li zi-Jie Lin Liu Yang Yue Wang Yue Li Wei-hua Cai Laboratory of Thermo-Fluid Science and Nuclear Engineering Northeast Electric Power UniversityJilin132000JilinChina School of Energy and Power Engineering Northeast Electric Power UniversityJilin132000JilinChina

The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 *** simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow *** results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were *** calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So hea

关键词： Printed circuit heat exchanger Vaporization Supercritical methane Pseudo-boiling Micro segment analysis

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Molecular mechanism for the unusual enhancement of the second-step chemiluminescence production from the carcinogenic tetrabromohydroquinone and H2O_(2)

引用

Journal of Environmental Sciences 2024年第7期141卷 330-342页

作者： zi-Han Wang Chun-hua huang Zhi-Sheng Liu Li Mao Ben-Zhan Zhu State Key Laboratory of Environmental Chemistry and Ecotoxicology Research Center for Eco-Environmental SciencesChinese Academy of SciencesBeijing 100085China College of Environment and Resources University of Chinese Academy of SciencesBeijing 100049China

We have found recently that two-step intrinsic hydroxyl radical(·OH)-dependent chemiluminescence(CL)could be produced by carcinogenic tetrahaloquinone and H_(2)O_(2).However,the first-step CL was too fast to clearly detect the stepwise generation of·OH and CL,and to distinguish the exact dividing point between the first-step and second-step *** we found that,extremely clear two-step intrinsic CL could be produced by the relative slow reaction of tetrabromohydroquinone(TBHQ)with H_(2)O_(2),which was directly dependent on the two-step·OH ***,the second-step,but not the first-step CL production of TBHQ/H_(2)O_(2)(CRET donor)was markedly enhanced by fluorescein(a typical xanthene dye,CRET acceptor)through a unique chemiluminescence resonance energy transfer(CRET)*** novel CRET system of TBHQ/H_(2)O_(2)/fluorescein was successfully applied for the sensitive detection of TBHQ with the detection limit as low as 2.5μmol/*** findings will help to develop more sensitive and highly efficient CL or CRET systems and specific CL sensor to detect the carcinogenic haloquinones,which may have broad environmental applications.

关键词： Two-step chemiluminescence Bromohydroquinone Hydrogen peroxide Hydroxyl radical CRET

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Impact of Local Climate Zones on the Urban Heat and Dry Islands in Beijing:Spatial Heterogeneity and Relative Contributions

引用

Journal of Meteorological Research 2024年第1期38卷 126-137页

作者： Zuofang ZHENG Fu luo Nana LI hua GAO Yuanjian YANG Institute of Urban Meteorology China Meteorological AdministrationBeijing 100089 School of Atmospheric Physics Nanjing University of Information Science&TechnologyNanjing 210044 Key Laboratory of Urban Meteorology China Meteorological AdministrationBeijing 100089

Based on the building height and density data on a 100-m resolution,hourly 2-m temperature and humidity data at83 automatic weather stations,and gridded local climate zone(LCZ)data on a 120-m resolution in urban Beijing in2020,this study first employs the semivariogram combined with building parameters to calculate spatial correlations and has identified an LCZ grid resolution of 500 m suitable for best usage of the available observation ***,how the spatially heterogeneous LCZs affect and contribute to the canopy urban heat island intensity(UHII)and urban dry island intensity(UDII)are quantitatively *** is found that UHII is high in winter and low in summer with a unimodal diurnal variation while UDI is low in winter but high in summer with a bimodal diurnal *** LCZ with compact mid-rise(open high-rise)buildings exhibits the highest UHII(UDII),followed by the compact high-rise(compact low-rise),while the LCZ of scattered trees presents both the lowest UHII and the lowest *** most significant difference in the UHII(UDII)among the nine LCZ types in the urban area of Beijing is2.62℃(1.1 g kg^(-1)).Area-weighted averaging analysis reveals that the open mid-rise LCZ is the most significant contributor to the UHII(UDII),immediately followed by compact mid-rise(open low-rise),with the least contribution from bare rock or paved(scattered trees).The results also indicate that beyond the intrinsic physical properties of the LCZs of a city,their area proportions cannot be overlooked in evaluating their impact on the UHI and *** quantitatively findings could help urban planners to create a livable urban climate and environment by adjusting the relevant land use.

关键词： local climate zone(LCZ) urban heat island(UHI) urban dry island(UDI) distribution pattern contribution rate Beijing

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Microstructure evolution of Ti_(48)Zr_(27)Cu_(6)Nb_(5)Be_(14)amorphous alloy after semi-solid isothermal treatment

引用

China Foundry 2024年第3期21卷 287-294页

作者： Xin-hua huang Jing-wen Pu Yong-xin luo Yue-jun Ouyang School of Material Electricity and Intelligent ManufacturingHuaihua UniversityHuaihua 330031HunanChina Hunan Renewable Aluminum Innovation Research Center Huaihua UniversityHuaihua 330031HunanChina

The as-cast amorphous Ti_(48)Zr_(27)Cu_(6)Nb_(5)Be_(14)composites,comprising in situ formedβ-Ti ductile crystalline precipitates,were prepared by water cooled copper mold suction ***,the semi-solid composites were obtained after the as-cast composites were treated by semi-solid isothermal *** microstructure evolution and kinetics of the composites were *** show that the microstructures of both the as-cast and semi-solid composites comprise ofβ-Ti crystal phases and amorphous matrix *** and after treatment,the crystals evolve from fine granular or fine dendritic crystals to coarse *** the treatment temperature increasing or the time prolonging,the average crystal size gradually increases and the surface morphology of the crystals gradually becomes *** studying the microstructural evolution and dynamics during the isothermal treatment process,it is found that the final morphology ofβ-Ti crystals is influenced by the isothermal treatment temperature and time(t),and theβ-Ti evolution rate increases with an increase in treatment *** addition,a linear relationship was observed between the size of cubicβ-Ti crystals(D^(3))and t;the growth kinetics factor K is 3.8μm^(3)·s^(-1).As the K value closes to 4μm^(3)·s^(-1),it is inferred the morphology evolution ofβ-Ti crystals is a coarsening behavior controlled by the diffusion of solute elements.

关键词： Ti_(48)Zr_(27)Cu_(6)Nb_(5)Be_(14) amorphous matrix composites semi-solid as-cast microstructure

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Gastrointestinal contrast-enhanced ultrasonography for diagnosis and treatment of peptic ulcer in children

引用

World Journal of Gastroenterology 2024年第7期30卷 705-713页

作者： Yu-hua Zhang Zhi-hua Xu Shuang-Shuang Ni Hong-Xia luo Department of Ultrasound The Second Affiliated Hospital of Wenzhou Medical UniversityWenzhou 325000Zhejiang ProvinceChina

BACKGROUND The detection rate of peptic ulcer in children is improving,with development of diagnostic *** is the gold standard for the diagnosis of peptic ulcer,but it is an invasive *** contrast-enhanced ultrasonography(CEUS)has the advantages of being painless,noninvasive,nonradioactive,easy to use,and *** To investigate the clinical value of CEUS for diagnosis and treatment of peptic ulcer in *** We investigated 43 children with digestive tract symptoms in our hospital from January 2021 to June *** children were examined by routine ultrasound,gastrointestinal CEUS,and *** pathological results of gastroscopy were taken as the gold *** ultrasonography was performed before gastrointestinal *** ultrasound showed the thickness of the gastroduodenal wall,gastric peristalsis,and the adjacent organs and tissues around the abdominal *** CEUS recorded the thickness of the gastroduodenal wall;the size,location and shape of the ulcer;gastric peristalsis;and adjacent organs and tissues around the abdominal *** results of routine ultrasound and gastrointestinal ultrasound were compared with those of gastroscopy to evaluate the diagnostic results and coincidence rate of routine ultrasound and gastrointestinal *** children received informed consent from their guardians for *** study was reviewed and approved by the hospital medical ethics *** Among the 43 children,17(15 male,2 female)were diagnosed with peptic ulcer by *** were 26 children with nonpeptic *** were eight cases of peptic ulcer and 35 of nonpeptic ulcer diagnosed by conventional *** diagnostic coincidence rate of peptic ulcer in children diagnosed by conventional ultrasound was 79.1%(34/43),which was significantly different from that of gastroscopy(P=0.033).It indicates that the coincidence rate of gastrointestinal contrast-enhanc

关键词： Contrast-enhanced ultrasound Peptic ulcer Children Gastrointestinal tract Abdominal pain Acoustic contrast agent

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Correlation between longitudinal crack occurrence and mold heat transfer in continuous casting based on process data mining

引用

Journal of Iron and Steel Research International 2024年第5期31卷 1139-1152页

作者： Zhi-qiang Peng zi-bing Hou Kai Yi Kun-hui Guo Dong-wei Guo Guang-hua Wen College of Materials Science and Engineering Chongqing UniversityChongqing400044China Chongqing Key Laboratory of Vanadium-Titanium Metallurgy and New Materials Chongqing UniversityChongqing400044China

The correlation between the longitudinal crack occurrence and integrated heat transfer of the mold with data mining methods was ***,three kinds of support vector machine models based on principal component analysis with different input features were established to explore the effect of integrated heat transfer on the accuracy of the prediction model for the longitudinal *** results show that the accuracy was improved while features including mean and standard deviation of integrated heat transfer were ***,the difference in integrated heat transfer between defect and normal samples under the same process parameters was quantitatively *** with normal samples,the temperature difference of cooling water for defect samples decreased by 0.65%,and the temperature difference fluctuation increased by 31.1%.Finally,the literature data were used to provide support for the quantitative correlation according to defect formation mechanism.A new criterion for the prediction of longitudinal crack and a discovering method for correlation between product quality and process parameters in the manufacturing industry have been provided.

关键词： Continuous casting slab Longitudinal surface crack Heat transfer Data mining Quantitative correlation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：