检索结果-南通市图书馆

Microstructure and tensile properties of magnesium nanocomposites fabricated using magnesium chips and carbon black

journal of Magnesium and Alloys 2020年第3期8卷 860-872页

作者： T.j.Lee w.j.Kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul 121-791Republic of Korea

In this study,carbon black(0,0.01,0.03 and 0.08 wt%)and AZ31(Mg-3Al-lZn)magnesium chips were used to fabricate carbon black-reinforced magnesium matrix composites with extrusion or a combination of extrusion and high-ratio differential speed *** hot pressing at 693 K and extrusion at 623 K with an extrusion ratio of 22,the magnesium chips coated with carbon black were soundly bonded into a bulk composite *** grain sizes of the extruded materials were similar with a size of 48.2-51.5|im despite the difference in the amount of carbon *** yield strength and ultimate tensile strength increased from 177 to 191 MPa and from 240 to 265 MPa,respectively,as a result of the addition of 0.01%carbon black;however,a further increase in the strength was marginal with additional carbon *** same trend was observed in the strain hardening *** tensile elongation increased by to the addition of 0.01%carbon black(from 15.8%to 17.4%)due to the increased work hardening effect,but decreased with additional carbon black due to its agglomeration and poor dispersion at higher *** high-ratio differential speed rolling(HRDSR)on the extruded materials and subsequent annealing,the AZ31 and AZ31 composites had a similar fine grain size of 16.3-17.9 *** annealed HRDSR composites showed the best mechanical properties at a higher content of carbon black(0.03%)compared to that(0.01%)for the extruded *** resulted from the enhanced dispersion effect of the carbon black due to the high shear flow induced during the HRDSR *** extruded composites exhibited the three distinct hardening stages(stage II,stage III and stage IV),while the annealed HRDSR composites mainly displayed the stage III *** addition of carbon black increased the strain hardening rate at all the strain hardening stages in both of the extruded and annealed HRDSR *** the initial hardening stage,the strain hardening rates of the extruded comp

关键词： Recycling Magnesium alloys chips Carbon black Nanocomposites Extrusion Differential speed rolling

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Glass-forming Ability and Corrosion Resistance of Zr—Cu—Al—Co Bulk Metallic Glass

引用

journal of Materials Science & Technology 2016年第4期32卷 349-354页

作者： w.Zhou w.P.weng j.X.Hou Shagang School of Iron and Steel Soochow University

Investigations were carried out to examine the effects of Co addition on the glass-forming ability （GFA） and corrosion resistance of Zr46Cu46AI8 bulk metallic glass in chloride-containing solution. It is found that the GFA of （Zr46Cu46Al8）100-xCox （x = 0, 1, 2, and 4 at.%） alloys reduces with the increase in Co content and correlates well with the parameters, such as the supercooled liquid region width ATx, the reduced glass transition temperature Trg and γ. The corrosion resistance is however found to be enhanced with the in- crease in Co concentration. The addition of Co causes the enrichment of Zr and Al, but depletes Cu in the surface films, which effectively enhances the corrosion potential and lowers the corrosion current density.

关键词： Bulk metallic glassCo-additionGlass-forming abilityCorrosion resistance

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of compressibility on the hypervelocity penetration

引用

Acta Mechanica Sinica 2018年第1期34卷 82-98页

作者： w.j.Song X.w.Chen P.Chen Department of Mechanics and Engineering Science College of Engineering Peking University Advanced Research Institute for Multidisciplinary Science Beijing Institute of Technology The State Key Lab of Explosion Science and Technology Beijing Institute of Technology Centre for Applied Physics and Technology (CAPT) Peking University

we further consider the effect of rod strength by employing the compressible penetration model to study the effect of compressibility on hypervelocity ***, we define different instances of penetration efficiency in various modified models and compare these penetration efficiencies to identify the effects of different factors in the compressible model. To systematically discuss the effect of compressibility in different metallic rod-target combinations, we construct three cases, i.e., the penetrations by the more compressible rod into the less compressible target, rod into the analogously compressible target, and the less compressible rod into the more compressible target. The effects of volumetric strain, internal energy, and strength on the penetration efficiency are analyzed simultaneously. It indicates that the compressibility of the rod and target increases the pressure at the rod/target interface. The more compressible rod/target has larger volumetric strain and higher internal energy. Both the larger volumetric strain and higher strength enhance the penetration or anti-penetration ability. On the other hand, the higher internal energy weakens the penetration or anti-penetration ability. The two trends conflict, but the volumetric strain dominates in the variation of the penetration efficiency, which would not approach the hydrodynamic limit if the rod and target are not analogously compressible. However, if the compressibility of the rod and target is analogous, it has little effect on the penetration efficiency.

关键词： Compressibility Hypervelocity penetration Equation of state(EOS) Shockwave Bernoulli equation

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effect of environments and normal loads on tribological properties of nitrided Ni(45)(FeCoCr)(40)(AlTi)(15)high-entropy alloys

引用

journal of Materials Science & Technology 2020年第7期42卷 85-96页

作者： L.w.Lan X.j.wang R.P.Guo H.j.Yang j.w.Qiao Research Center for High-Entropy Alloys College of Materials Science and EngineeringTaiyuan University of TechnologyTaiyuan030024China

The tribological properties of nitrided Ni(45)(FeCoCr)(40)(AlTi)(15)high-entropy alloys(HEAs)were investigated in air and simulated acid rain under different normal loads(5,7,10,and 12 N)at ambient *** results revealed that as-cast HEAs were only composed of FCC phase,while the volume fraction of FCC phase in the nitrided alloys was significantly ***,the hard phases of AIN,CrN,Fe4 N,and TiN phases were formed in the nitrided *** thickness of the nitriding layer was about 8.4μ*** hardness increased from 8.7 GPa in as-cast alloys to 14.5 GPa in the nitrided *** addition,under the same conditions,the friction coefficient of the nitrided alloys was higher than that of as-cast alloys,but the wear rate was generally lower than that of as-cast ***,the wear rate of the nitrided alloys was the lowest in acid rain due to the lubrication,cleaning,and cooling in the liquid *** air,dominating wear mechanisms in as-cast and nitrided alloys were abrasive,delamination,and adhesive ***,the wear mechanism of as-cast and nitrided alloys in acid rain was mainly abrasive and corrosion wears.

关键词： Abrasive wear Hardness Corrosive wear Microstructure wear mechanism

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Microstructure and mechanical optimization of probeless friction stir spot welded joint of an Al-Li alloy

引用

journal of Materials Science & Technology 2018年第10期34卷 1739-1746页

作者： Q. Chu w.Y. Li X.w. Yang j.j. Shen A. Vairis w.Y. Feng w.B. wang State Key Laboratory of Solidification Processing Shaanxi Key Laboratory of Friction Welding Technologies Northwestern Polytechnical University Xi'an710072 China Helmholtz-Zentrum Geesthacht Institute of Materials Research Materials Mechanics Geesthacht 21502 Germany Mechanical Engineering Department TEl of Crete Heraklion Crete 71004 Greece China PSw Center Beijing 100024 China

In this work, a third generation AI-Li alloy has been successfully spot welded with probeless friction stir spot welding （P-FSSw）, which is a variant of conventional friction stir welding. The Box-Behnken exper-imental design in response surface methodology （RSM） was applied to optimize the P-FSSw parameters to attain maximum tensile/shear strength of the spot joints. Results show that an optimal failure load of 7.83 kN was obtained under a dwell time of 7.2 s, rotation speed of 950 rpm and plunge rate of 30 mm/rain. Sufficient dwell time is essential for heat conduction, material flow and expansion of the stir zone to form a sound joint. Two fracture modes were observed, which were significantly affected by hook defect. In addition to mechanical testing, electron backscattering diffraction （EBSD） and differential scanning calorimetry （DSC） were used for microstructure evolution and property analysis. The precipitation of GP zone and AI3Li as well as the ultrafine grains were responsible for the high microhardness in the stir zone.

关键词： Probeless friction stir spot welding Precipitation Mechanical property Fracture mechanism

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Extending the Relational Model to Deal withProbabilistic Data

引用

journal of Computer Science & Technology 2000年第3期15卷 230-240页

作者：马宗民 ZHANG w.j MA w.Y CityUniversityofHongKong KowloonHongKongP.R.China

According to the soundness and completeness of information in databases, the expressive form and the semantics of incomplete information are discussed in this paper. On the basis of the discussion, the current studies on incomplete data in relational databases are reviewed. In order to represent stochastic uncertainty in most general sense in the real world, probabilistic data are introduced into relational databases. An extended relational data model is presented to express and manipulate probabilistic data and the operations in relational algebra based on the extended model are defined in this paper.

关键词： incomplete information uncertain information extended relational model probabilistic data relational algebra

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Optimum operation conditions of nitrogen and phosphorus removal by a biofilm-activated-sludge system

引用

journal of Environmental Sciences 2003年第1期15卷 25-30页

作者： LIUjun－xin j．w．vanGroenestijin ResearchCentreforEco－EnviromentalSciences ChineseAcademyofSciencesBeijing100085China DepartmentofEnvironmentalBiotechnoloty TNOInstituteofEnviromentalSciencesEnergyReseachandProc

In the biofilm and activated sludge combined system, denitrifying bacteria attached on the fibrous carriers in the anoxic tank, while the sludge containing nitrifying and phosphorus removal bacteria was only recirculated between the aerobic and anaerobic tanks. Therefore, the factors affected and restricted nitrification, denitrification and phosphorus removal in a traditional A/A/O process were resolved. This paper describes the optimum operation conditions for nitrogen and phosphorus removal using this system.

关键词： nitrification denitrification phosphorus removal biofilm activated sludge

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Comeld^TM joints: A Novel Technique for Bonding Composites and Metal

引用

稀有金属材料与工程 2009年第A03期38卷 134-141页

作者： Tu w Guild F j Hogg P j Queen Mary University of London Imperial College London South Kensington Campus University of Manchester PO Box 88

Current and future structural applications for composite laminates frequently involve design solutions combining composite laminates and metal; the materials must be joined. Two conventional means of joining are available mechanical joining and adhesive bonding. Both methods have critical disadvantages. A novel surface treatment for metals developed at TwI, Surfi-Sculpt, leads to the formation of surface protrusions on metal surfaces. These protrusions are typically 1.0 mm high and 0.6 mm in diameter. The surface modified metal can be bonded with composite laminates to form a Comeld～TM joint. These joints can be described as a combination of mechanical fastening and adhesive bonding. This paper describes our current work using finite element modelling to optimize the protrusions in respect to their geometry and distribution. The simulations require multi-scale modelling techniques to transfer results between the global model of the whole joint and the unit cell models containing a protrusion. Results from the simulations show critical effects on stress distributions arising from changing protrusion geometry. These joints show significant advantages over conventional adhesive joining technologies and their application would allow improved performance for combinations of metal and composite laminates.

关键词：复合材料金属表面处理技术物理性能

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

On Exact Conservation for the Euler Equations with Complex Equations of State

引用

Communications in Computational Physics 2010年第10期8卷 995-1015页

作者： j.w.Banks Center for Applied Scientific Computing Lawrence Livermore National LaboratoryLivermoreCA 94551USA

Conservative numerical methods are often used for simulations of fluid flows involving shocks and other jumps with the understanding that conservation guarantees reasonable treatment near *** is true in that convergent conservative approximations converge to weak solutions and thus have the correct shock ***,correct shock location results from any discretization whose violation of conservation approaches zero as the mesh is *** we investigate the case of the Euler equations for a single gas using the jones-wilkins-Lee(jwL)equation of *** show that a quasi-conservative method can lead to physically realistic solutions which are devoid of spurious pressure ***,we demonstrate that under certain conditions,a quasi-conservative method can exhibit higher rates of convergence near shocks than a strictly conservative counterpart of the same formal order.

关键词： Euler equations complex EOS jwL EOS Godunov methods

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Grain size and temperature effect on the tensile behavior and deformation mechanisms of non-equiatomic Fe(41)Mn(25)Ni(24)Co8Cr2high entropy alloy

引用

journal of Materials Science & Technology 2020年第7期42卷 190-202页

作者： H.T.jeong w.j.Kim Department of Materials Science and Engineering Hongik UniversityMapo-guSangsu-dong 72-1Seoul121-791Republic of Korea

The effect of the grain size on the tensile properties and deformation mechanisms of a nonequiatomic Fe(41)Mn(25)Ni(24)Co8 Cr2 high-entropy alloy was studied in the temperature range between 298 and 1173 K by preparing the samples with three different grain sizes through severe plastic deformation and subsequent annealing:ultrafine(sub)grain size(≤0.5μm),8.1μm and 590.2μ*** the temperature between 298 and773 K,the material with the large grain size of 590.2μm exhibited the largest tensile ductility(57%-82%)due to its high strain hardening associated with mechanical twinning,but it exhibited the lowest strength due to its large grain *** material with the ultrafine(sub)grain size exhibited the lowest tensile ductility(3%-7%)due to a greatly reduced strain hardening ability after severe plastic deformation,but it exhibited the highest strength due to the dislocation strengthening and grain refinement *** tensile testing at temperatures above 973 K,recrystallization occurred in the material with the ultrafine(sub)grains during the sample heating and holding stage,leading to the formation of fine and equiaxed grains with the sizes of 6.8-13.5μ*** deformation behavior of the Fe(41)Mn(25)Ni(24)Co8 Cr2 with different grain sizes in the high temperature range between 973 and 1173 K,where pseudosteady-state flow was attained in the stress-strain curves,could be explained by considering the simultaneous contribution of grain boundary sliding and dislocation-climb creep to total plastic *** activation energies for plastic flow for the materials with different grain sizes were similar as^199 kj/*** predicting the deformation mechanism,it was important to consider the change in grain size by rapid grain growth or recrystallization during the sample heating and holding stage because grain boundary sliding is a grain-size-dependent deformation *** sample with the ultrafine(sub)grains exhibited the large tensile elongations of 30%-85%due to it

关键词： High entropy alloys Grain size High temperature deformation mechanism Tensile behavior Grain boundary sliding

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：