检索结果-南通市图书馆

Natural Convection of a Power-Law Nanofluid in a Square Cavity with a Vertical Fin

Fluid Dynamics & Materials Processing 2024年第9期20卷 2091-2108页

作者： Amira M’hadbi Mohammed El Ganaoui Haïkel Ben hamed Amenallah Guizani Khalid Chtaibi LERMAB Department of Transition and Energy Efficiency ProfessionsIUT H Poincaréde LongwyUniversity of LorraineLongwy54400France LPT Center for Energy Research and Technologies(Borj Cedria2084)University of Tunis El ManarTunis1068Tunisia LTI Department of Mechanical Engineering and ProductionIUTUniversity of Picardie Jules-VerneAmiens80025France

The behavior of non-Newtonian power-law nanofluids under free convection heat transfer conditions in a cooled square enclosure equipped with a heated fin is investigated *** particular,the impact of nanofluids,composed of water and Al_(2)O_(3),TiO_(2),and Cu nanoparticles,on heat transfer enhancement is *** aim of this research is also to analyze the influence of different parameters,including the Rayleigh number(Ra=10^(4)-10^(6)),nanoparticle volume fraction(φ=0%-20%),non-Newtonian power-law indexes(n=0.6-1.4),and fin dimensions(Ar=0.3,0.5,and 0.7).Streamlines and isotherms are used to depict flow and related heat transfer *** indicate that thermal performance improves with increasing Rayleigh number,regardless of the nanoparticle type or nanofluid rheological *** suggests that the buoyancy force has a significant impact on heat transfer,particularly near the heat *** Nusselt number is more sensitive to variations in Cu nanoparticle volume fractions compared to Al₂O₃and TiO₂.Moreover,the average Nusselt numbers for power-law nanofluids with n1)are greater(smaller)than for Newtonian fluids due to the decrease(increase)in viscosity with increasing(decreasing)shear rate,at the same values of Rayleigh number Ra owing to the amplification(attenuation)of the convective ***,the most substantial enhancement is observed with Cu-water shear-thinning nanofluid,where the Nusselt number increases by 136%when changing from Newtonian to shear thinning behavior and by 154.9%when adding 16%nanoparticle volume ***,an even larger increase of 57%in the average Nusselt number is obtained on increasing the fin length from 0.3 to 0.7.

关键词： Heat transfer nanofluid non-Newtonian fluid natural convection

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Insulin therapy in type 2 diabetes: Insights into clinical efficacy, patient-reported outcomes, and adherence challenges

引用

World Journal of Diabetes 2024年第5期15卷 828-852页

作者： Mahmoud Emad-Eldin Gehan F Balata Eman A Elshorbagy Mona S hamed Mohamed S Attia Department of Pharmacy Practice Faculty of PharmacyZagazig UniversityZagazig HFQM+872Al-Sharqia GovernorateEgypt Department of Pharmacy Practice Faculty of PharmacyHeliopolis UniversityCairo 44519Egypt Department of Pharmaceutics Faculty of PharmacyZagazig UniversityZagazig 44519Al-Sharqia GovernorateEgypt Department of Internal Medicine Faculty of MedicineZagazig UniversityZagazig 44519Al-Sharqia GovernorateEgypt Department of Community at Faculty of Medicine Zagazig UniversityZagazig 44519Al-Sharqia GovernorateEgypt

Insulin therapy plays a crucial role in the management of type 2 diabetes as the disease *** the past century,insulin formulations have undergone significant modifications and bioengineering,resulting in a diverse range of available insulin *** products show distinct pharmacokinetic and pharmacodynamic ***,various insulin regimens have em-erged for the management of type 2 diabetes,including premixed formulations and combinations of basal and bolus *** utilization of different insulin regimens yields disparate clinical outcomes,adverse events,and,notably,patient-reported outcomes(PROs).PROs provide valuable insights from the patient’s perspective,serving as a valuable mine of information for enhancing healthcare and informing clinical *** to insulin therapy,a critical patient-reported outcome,significantly affects clinical outcomes and is influenced by multiple *** review provides insights into the clinical effectiveness of various insulin preparations,PROs,and factors impacting insulin therapy adherence,with the aim of enhancing healthcare practices and informing clinical decisions for individuals with type 2 diabetes.

关键词： Adherence Diabetes Insulin Patient-reported outcomes Pharmacokinetic Pharmacodynamic

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Tailoring the microstructure， tensile properties， and creep resistance of additively manufactured Inconel 718 superalloy by post-processing

引用

Transactions of Nonferrous Metals Society of China 2024年

作者： Sajad Ghaemifar Milad Roostaei Mohammad Reza Zamani Stefan Wurster hamed Mirzadeh School of Metallurgy and Materials Engineering College of Engineering University of Tehran Erich Schmid Institute of Materials Science Austrian Academy of Sciences Department of Materials Science Chair of Materials Physics Montanuniversit?t Leoben

Effects of post-processing heat treatments on the microstructure， aging kinetics， and room/elevated temperature mechanical properties of additively manufactured Inconel 718 superalloy were investigated. Scanning electron microscopy (SEM)， electron backscattered diffraction (EBSD)， and X-ray diffraction (XRD)， as well as hardness， tensile， and creep testing were used for characterization. At temperatures higher than 1100 °C， homogenization treatment resulted in the appearance of equiaxed grains by recrystallization and diminishing the dislocation density. The precipitation activation energy for the homogenized aged condition was obtained as 203 kJ/mol， which was higher than the value of ～160 kJ/mol for the as-built IN718 superalloy. Therefore， direct aging resulted in a faster aging response， which led to a significant improvement in tensile properties， as rationalized by the strengthening mechanisms. Direct aging treatment resulted in a higher elevated-temperature ultimate tensile strength (UTS) as well as the optimum creep life and lowest minimum creep rate in comparison with other heat treating routes， which were attributed to the presence of fine and uniformly dispersed strengthening precipitates in conjunction with the high dislocation density.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

挤压速度对搅拌摩擦反挤压法制备Cu-5%Ti_(2)SnC复合丝材性能的影响

引用

Transactions of Nonferrous Metals Society of China 2024年第3期34卷 935-951页

作者： Amirhossein JAHANI hamed JAMSHIDI AVAL Mohammad RAJABI Roohollah JAMAATI Department of Materials Engineering Babol Noshirvani University of TechnologyShariati AvenueBabol 47148-71167Iran

对粉末冶金法制备的含5%(体积分数)Ti_(2)Sn CMAX相的初始复合材料进行搅拌摩擦反挤压(FSBE)处理,研究FSBE工艺的轴向横移速度对Cu-Ti_(2)Sn C复合线材显微组织、力学性能、电学性能和磨损性能的影响。结果表明,随着挤压速度的增加,显... 详细信息

对粉末冶金法制备的含5%(体积分数)Ti_(2)Sn CMAX相的初始复合材料进行搅拌摩擦反挤压(FSBE)处理,研究FSBE工艺的轴向横移速度对Cu-Ti_(2)Sn C复合线材显微组织、力学性能、电学性能和磨损性能的影响。结果表明,随着挤压速度的增加,显微组织中孪晶增多,Ti_(2)SnC颗粒细化,MAX相和Cu基体之间的界面结合改善。当转速为600r/min,轴向横移速度为25mm/min时,Cu-Ti_(2)SnC复合线材具有最大的硬度、屈服强度和极限抗拉强度,分别为HV 132.7、278.34MPa和485.15MPa,这是其更强的界面结合和更细的MAX相导致的。此外,当转速为600 r/min,轴向横移速度为25 mm/min时,Cu-Ti_(2)SnC复合丝的电导率最高,达到89.21%(IACS),磨损率最低,为0.0015 mg/m,这是其更大的晶粒尺寸、更强的界面结合与更低的密度导致的。

关键词：搅拌摩擦反挤压 Ti_(2)SnC MAX相铜基复合材料电导率

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

几何形状对气垫升力的影响研究

引用

哈尔滨工程大学学报（英文版） 2024年第1期23卷 74-84页

作者： hamed Petoft Vahid Fakhari Abbas Rahi Faculty of Mechanical and Energy Engineering Shahid Beheshti UniversityTehran ***Iran

One of the crucial and challenging issues for researchers is presenting an appropriate approach to evaluate the aerodynamic characteristics of air cushion vehicles(ACVs)in terms of system design *** of these issues includes introducing a suitable approach to analyze the effect of geometric shapes on the aerodynamic characteristics of *** main novelty of this paper lies in presenting an innovative method to study the geometric shape effect on air cushion lift force,which has not been investigated thus ***,this paper introduces a new approximate mathematical formula for calculating the air cushion lift force in terms of parameters,including the air gap,lateral gaps,air inlet velocity,and scaling factor for the first ***,we calculate the aerodynamic lift force applied to nine different shapes of the air cushions used in the ACVs in the present paper through the ANSYS Fluent *** geometrical shapes studied in this paper are rectangular,square,equilateral triangle,circular,elliptic shapes,and four other combined shapes,including circle-rectangle,circle-square,hexagonal,and fillet *** showed that the cushion with a circular pattern produces the highest lift force among other geometric shapes with the same *** increase in the cushion lift force can be attributed to the fillet with a square shape and its increasing radius compared with the square shape.

关键词： Lift force Air cushion vehicle Geometric shape Simulation Gap Inlet velocity Scaling factor

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Interplay between temperature-dependent strengthening mechanisms and mechanical stability in high-performance austenitic stainless steels

引用

International Journal of Minerals,Metallurgy and Materials 2024年第10期31卷 2182-2188页

作者： Mohammad Javad Sohrabi hamed Mirzadeh Saeed Sadeghpour Milad Zolfipour Aghdam Abdol Reza Geranmayeh Reza Mahmudi School of Metallurgy and Materials Engineering College of EngineeringUniversity of Tehran Centre for Advanced Steels Research Materials and Mechanical EngineeringUniversity of Oulu Department of Mechanical Engineering College of EngineeringUniversity of Tehran

The effects of deformation temperature on the transformation-induced plasticity(TRIP)-aided 304L, twinning-induced plasticity(TWIP)-assisted 316L, and highly alloyed stable 904L austenitic stainless steels were compared for the first time to tune the mechanical properties, strengthening mechanisms, and strength–ductility synergy. For this purpose, the scanning electron microscopy(SEM),electron backscattered diffraction(EBSD), X-ray diffraction(XRD), tensile testing, work-hardening analysis, and thermodynamics calculations were used. The induced plasticity effects led to a high temperature-dependency of work-hardening behavior in the 304L and 316L stainless steels. As the deformation temperature increased, the metastable 304L stainless steel showed the sequence of TRIP, TWIP, and weakening of the induced plasticity mechanism; while the disappearance of the TWIP effect in the 316L stainless steel was also ***, the solid-solution strengthening in the 904L superaustenitic stainless steel maintained the tensile properties over a wide temperature range, surpassing the performance of 304L and 316L stainless steels. In this regard, the dependency of the total elongation on the deformation temperature was less pronounced for the 904L alloy due to the absence of additional plasticity mechanisms. These results revealed the importance of solid–solution strengthening and the associated high friction stress for superior mechanical behavior over a wide temperature range.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Actuator and sensor fault isolation in a class of nonlinear dynamical systems

引用

Journal of Automation and Intelligence 2024年第2期3卷 57-72页

作者： hamed Tirandaz Christodoulos Keliris Marios M.Polycarpou KIOS Research Center for Intelligent Systems and Networks and the Department of Electrical and Computer EngineeringUniversity of CyprusNicosia 1678Cyprus

Fault isolation in dynamical systems is a challenging task due to modeling uncertainty and measurement noise,interactive effects of multiple faults and fault *** paper proposes a unified approach for isolation of multiple actuator or sensor faults in a class of nonlinear uncertain dynamical *** and sensor fault isolation are accomplished in two independent modules,that monitor the system and are able to isolate the potential faulty actuator(s)or sensor(s).For the sensor fault isolation(SFI)case,a module is designed which monitors the system and utilizes an adaptive isolation threshold on the output residuals computed via a nonlinear estimation scheme that allows the isolation of single/multiple faulty sensor(s).For the actuator fault isolation(AFI)case,a second module is designed,which utilizes a learning-based scheme for adaptive approximation of faulty actuator(s)and,based on a reasoning decision logic and suitably designed AFI thresholds,the faulty actuator(s)set can be *** effectiveness of the proposed fault isolation approach developed in this paper is demonstrated through a simulation example.

关键词： Actuator and sensor fault isolation Adaptive approximation Observer-based fault diagnosis Reasoning-based decision logic

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Expression and characterization of a novel GH128 laminarinase OUC-BsLam26 harboring both hydrolyzing and transferring activities

引用

Food Science and Human Wellness 2024年

作者： Yueyang Dong Yongyi Quan Hong Jiang hamed I.Hamouda Zewei Lu Yimiao Chen Chengqiang Li Xiangzhao Mao State Key Laboratory of Marine Food Processing and Safety Control College of Food Science and Engineering Ocean University of China Qingdao Key Laboratory of Food Biotechnology Sanya Ocean Research Institute Ocean University of China Processes Design and Development Department Egyptian Petroleum Research Institute Laboratory for Marine Drugs and Bioproducts of Qingdao National Laboratory for Marine Science and Technology Key Laboratory of Biological Processing of Aquatic Products China National Light Industry

Laminarin oligosaccharides (LOSs) with a specific degree of polymerization prepared through the laminarin degradation via laminarinase present more significant nutritional functions and application values. Human intestinal bacteria are promising potential producers of novel carbohydrate-active enzymes with unique properties. Here， a novel glycoside hydrolase family 128 (GH128) laminarinase OUC-BsLam26 from the intestinal bacterium Bacteroides sp. CBA7301 was heterologously expressed and characterized. The recombinant OUC-BsLam26 with a molecular mass of 49.86 kDa exhibits highest activity (6.60 U/mg) at 45 ℃ and pH 6.0， which shows noticeable temperature and pH stability. The purified OUC-BsLam26 could degrade laminarin via an endo-type mode with the generation of laminaripentaose， laminaritetraose， laminaritriose， and laminaribiose， among them， laminaritetraose is the principal product， which accounts for 45.25% of the total products， which is significantly different from the reported GH128 laminarinases. The minimum recognition substrate of OUC-BsLam26 is laminarihexaose. Furthermore， OUC-BsLam26 also could catalyze the transglycosylation process with the production of some novel glycosides. Altogether， the intestinal bacterium Bacteroides sp. CBA7301 contains laminarinase with unique product composition and OUC-BsLam26 is a hopeful bio-catalyst with the potential to produce laminaritetraose and some novel glycosides.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Deep Transfer Learning Techniques in Intrusion Detection System-Internet of Vehicles: A State-of-the-Art Review

引用

Computers, Materials & Continua 2024年第8期80卷 2785-2813页

作者： Wufei Wu Javad Hassannataj Joloudari Senthil Kumar Jagatheesaperumal Kandala N.V.P.SRajesh Silvia Gaftandzhieva Sadiq Hussain Rahimullah Rabih Najibullah Haqjoo Mobeen Nazar hamed Vahdat-Nejad Rositsa Doneva School of Information Engineering Nanchang UniversityNanchang330031China Department of Computer Engineering Technical and Vocational University(TVU)Tehran***Iran Department of Computer Engineering University of BirjandBirjand***Iran Department of Computer Engineering Babol BranchIslamic Azad UniversityBabol***Iran Department of Electronics&Communication Engineering Mepco Schlenk Engineering CollegeSivakasi626005India School of Electronics Engineering VIT-AP UniversityNear Vijayawada522237India Faculty of Mathematics and Informatics University of Plovdiv Paisii HilendarskiPlovdiv4000Bulgaria Examination Branch Dibrugarh UniversityDibrugarh786004India Department of Computer Engineering Faculty of EngineeringUniversity of BirjandBirjand***Iran Faculty of Electrical and Computer Engineering University of BirjandBirjand***Iran Malaysian Institute of Information Technology Universiti Kuala LumpurKuala Lumpur50250Malaysia Faculty of Physics and Technology University of Plovdiv Paisii HilendarskiPlovdiv4000Bulgaria

The high performance of IoT technology in transportation networks has led to the increasing adoption of Internet of Vehicles(IoV)*** functional advantages of IoV include online communication services,accident prevention,cost reduction,and enhanced traffic *** these benefits,IoV technology is susceptible to cyber-attacks,which can exploit vulnerabilities in the vehicle network,leading to perturbations,disturbances,non-recognition of traffic signs,accidents,and vehicle *** paper reviews the state-of-the-art achievements and developments in applying Deep Transfer Learning(DTL)models for Intrusion Detection Systems in the Internet of Vehicles(IDS-IoV)based on anomaly ***-IoV leverages anomaly detection through machine learning and DTL techniques to mitigate the risks posed by *** systems can autonomously create specific models based on network data to differentiate between regular traffic and *** these techniques,transfer learning models are particularly promising due to their efficacy with tagged data,reduced training time,lower memory usage,and decreased computational *** evaluate DTL models against criteria including the ability to transfer knowledge,detection rate,accurate analysis of complex data,and *** review highlights the significant progress made in the field,showcasing how DTL models enhance the performance and reliability of IDS-IoV *** examining recent advancements,we provide insights into how DTL can effectively address cyber-attack challenges in IoV environments,ensuring safer and more efficient transportation networks.

关键词： Cyber-attacks internet of things internet of vehicles intrusion detection system

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Influence of processing history on microstructure， mechanical properties， and electrical conductivity of Cu-0.7Mg alloy

引用

Transactions of Nonferrous Metals Society of China 2024年

作者： Alireza KALHOR Kinga RODAK Marek TKOCZ Bartosz CHMIELA Ivo SCHINDLER ?ukasz POLOCZEK Krzysztof RADWA?SKI hamed MIRZADEH Marian KAMPIK Faculty of Materials Engineering Silesian University of Technology V?B – Technical University of Ostrava Faculty of Materials Science and Technology Materials Research Group ?ukasiewicz Upper Silesian Institute of Technology School of Metallurgy and Materials Engineering College of Engineering University of Tehran Faculty of Electrical Engineering Silesian University of Technology

The effects of forward extrusion as well as extrusion combined with reversible torsion (KoBo extrusion)， followed by additional deformation via the MaxStrain module of the Gleeble thermomechanical simulator， on the microstructure， mechanical properties， and electrical conductivity of a Cu-0.7Mg (wt.%) alloy， were investigated in this work. The simulation results highlighted the critical influence of processing history in determining the equivalent strain distribution. The sample subjected to forward extrusion at 400 ℃and subsequent MaxStrain processing (FM sample)， possessed 76% lower grain size compared to the sample processed solely with MaxStrain (AM sample). Likewise， the KoBo-extruded and MaxStrain-processed sample (KM sample) exhibited 66% smaller grain size compared to the AM sample. Tensile test results revealed that the AM， FM， and KM samples， respectively， possessed 251%， 288%， and 360% higher yield strength， and 95%， 121%， and 169% higher tensile strength compared to the initial annealed alloy， as a result of grain refinement as well as deformation strengthening. Finally， the electrical conductivity measurements revealed that AM， FM， and KM samples， respectively， possessed electrical conductivity values of 37.9， 35.6， and 32.0 (MS/m)， which， considering their mechanical properties， makes them eligible to be categorized as high-strength and high-conductivity copper alloys.

关键词：

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：