检索结果-南通市图书馆

Production of AZ80/Al composite rods employing non-equal channel lateral extrusion

Transactions of Nonferrous Metals Society of China 2016年第5期26卷 1276-1283页

作者： Mohammad ASGARI faramarz fereshteh-saniee Mechanical Engineering Department Faculty of Engineering Bu-Ali Sina University

In order to simultaneously take the advantages of magnesium and aluminum alloys, AZ80/A1 composite rods were produced using non-equal channel lateral extrusion （NECLE） process at different temperatures. Scanning electron microscope （SEM） and energy dispersive spectrometer （EDS） tests as well as the shear punch test were employed to study the quality and strength of the bond between the two alloys. It was found that the process temperature was an important factor affecting the level of interfacial bonding, such that increasing the temperature from 250 to 300℃ has improved the strength by 37% and the thickness of the bond between the layers by 4.5%. Moreover, this temperature rise reduced the maximum required forming load by 13%. However, the hardness tests showed that this increase in the process temperature resulted in 4% decrease in the hardness of the composite bar.

关键词： bimetallic composite magnesium alloy aluminum alloy mechanical properties co-extrusion welding non-equal channel lateral extrusion

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Influence of roll speed difference on microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling process

引用

Transactions of Nonferrous Metals Society of China 2021年第4期31卷 901-912页

作者： Mohammad Mehdi AMIRI faramarz fereshteh-saniee Department of Mechanical Engineering Faculty of EngineeringBu-Ali Sina UniversityHamedan 65178Iran

The influences of the dissimilarity in the roll speeds on the microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling(CCCR) process were investigated. Several experiments were conducted with three different upper/lower roll rotational speed ratios(ω/ω0, ω is the upper roll rotational speed and ω0 is the lower roll rotational speed), namely 1:1, 1:1.2 and 1:1.4. It was found that the greatest dissimilarity in the roll speed(ω/ω0=1:1.4) improved the yield strength and ultimate tensile strength of 7075 Al plate in the rolling direction by 41.5% and 21.9%, respectively. Moreover, at a roll speed ratio of ω/ω0=1:1.4, the average grain size was decreased by 36% whereas the mean hardness of the transverse cross-section of the finally rolled plate was increased by about 9.2%. Texture studies also revealed that the more the difference in the roll speeds was, the greater the isotropy and the hardness of the final product were. Nevertheless, conducting CCCR operation with different roll speeds resulted in about 6% reduction in the elongation of the deformed plate.

关键词： continuous casting and rolling 7075 Al alloy roll speed difference microstructure mechanical properties texture anisotropy

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Effects of die geometry on non-equal channel lateral extrusion(NECLE) of AZ80 magnesium alloy

引用

Transactions of Nonferrous Metals Society of China 2014年第10期24卷 3274-3284页

作者： faramarz fereshteh-saniee Mohammad ASGARI Mahmoud BARATI Sayed Mahmoud PEZESHKI Mechanical Engineering Department Faculty of Engineering Bu-Ali Sina University Applied Mechanics Department Faculty of Mechanical Engineering K.N. Toosi University of Technology

Non-equal channel lateral extrusion（NECLE） is a new process that can be used to attain higher grain refinement in comparison with equal channel lateral extrusion（ECLE）. The die design for this process was numerically and experimentally studied. After finding a good correlation between the numerical and experimental results, more comprehensive FE analyses were carried out. Different die geometrical parameters were considered and their effects on the induced plastic strain, stress distribution, velocity field and forming load of the process were investigated. It was found that by this process with a suitable set of die geometrical parameters, higher induced effective strain and more homogeneous strain distribution could be achieved in comparison with ECLE operation.

关键词： magnesium alloy non-equal channel lateral extrusion(NECLE) die geometry homogeneity arbitrary Lagrangian-Eulerian(ALE) method

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：