检索结果-南通市图书馆

国外油气勘探 1988年第1期 58-61页

作者： ekstiem m.p 石燕

引言地球物理测井的最早目的是在井场提供关于储集层的详细描述,否则就要采用费时长化费高的全井取心工作。当然,这些年来已经研究出许多井下测量方法,通过仔细的解释,可求出储集层的重要岩石物理参数、几何形态、厚

关键词：地层扫描器粉砂石灰岩岩心井壁照片碎屑沉积物碳酸盐岩岩芯储集层储层地层电阻率地层倾角极板电极排列电极系裂缝系统微电阻沉积特征

BaTiO_(3)solid solutions co-doped with Gd^(3+)and Eu^(3+):Synthesis,structural evolution and dielectric properties

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Journal of Rare Earths 2024年第10期42卷 1920-1926页

作者： R.martínez-López m.pérez-Labra J.A.Romero-Serrano F.R.Barrientos-Hernández m.Reyes-pérez m.I.Valenzuela-Carrillo G.Urbano-Reyes V.E.Reyes-Cruz G.I.Dávila-pulido Academic Area of Earth Sciences and materials Autonomous University of Hidalgo StateRoad Pachuca-Tulancingo Km 4.5 Mineral de La Reforma.Hidalgo42184Mexico metallurgy and materials Department ESIQIE-IPNUPALMZacatencoCiudad de Mexico07738Mexico Autonomous University of Coahuila Boulevard Adolfo López Mateos S/nNueva RositaCoahuila26800Mexico

In this paper,the synthesis,structural evolution,and dielectric properties of BaTiO_(3)solid solutions codoped with rare earth elements(Gd^(3+)and Eu^(3+))prepared using the solid-state reaction method are *** pure precursor powders of BaCl_3,TiO_(2),Gd_(2)O_(3),and Eu_(2)O_(3)were mixed in stoichiometric proportions,ground in an agate mortar before being uniaxially pressed at 250 mpa and sintered at 1300℃in air atmosphere for 6 h to obtain Ba_(1-3x)Gd_(2x)Ti_(1-3x)Eu_(4x)O_(3)(x=0,0.0015,0.01 and0.1).X-ray diffraction(XRD)and Rietveld's refinement results reveal the crystal phase ferroelectric tetragonal BaTiO_(3)for the samples with x=0,0.0015 and 0.01,as well as a consistent increment in the lattice parameters caused by the *** solubility limit of Gd^(3+)and Eu^(3+)in the BaTiO_(3)structure is reached for the sample with x>0.01,and the orthorhombic Eu_2TiO_(5)and monoclinic BaTi_(2)O_(5)secondary phases were *** Raman results show the characteristic peaks of ferroelectric tetragonal BaTiO_(3)around 716 cm^(-1)(LO of A1 symmetry),515 cm^(-1)(TO of A1 symmetry),and 305 cm^(-1)(B1).The maximum relative permittivity measured at 1 kHz was recorded to be 6151.8 for the sample with x=0.0015,and a decrease in the Curie temperature to 105℃with respect to the undoped sample was *** punctual microanalysis for the samples with x=0.0015,0.01,and 0.1 reveals grains composed of Ba,Ti,O,Gd,and Eu homogeneously distributed in the BaTiO_(3)*** Ba/Ti ratios for samples with x=0.0015,0.01 and 0.1 are 2.86,2.91,and 0.68,respectively,indicating substitution at the Ti site for samples with x=0.0015 and 0.01 and a substitution at the Ba site for the sample with x=0.1.

关键词： BaTiO_(3) Doping Gadolinium Europium Synthesis Rare earths

Selection of digital fabrication technique in the construction industry--A multi-criteria decision-making approach

在线全文

学校读者我要写书评

暂无评论

Frontiers of Structural and Civil Engineering 2024年第7期18卷 977-997页

作者： m.p.SALAImANImAGUDAm J.JAYApRAKASH Department of Structural and Geotechnical Engineering School of Civil EngineeringVellore Institute of TechnologyVellore 632014India

Digital fabrication techniques,in recent decades,have provided the basis of a sustainable revolution in the construction ***,selecting the digital fabrication method in terms of manufacturability and functionality requirements is a complex *** paper presents alternatives and criteria for selection of digital fabrication techniques by adopting the multi-criteria decision-making *** alternatives considered in the study are concrete three-dimensional(3D)printing,shotcrete,smart dynamic casting,material intrusion,mesh molding,injection concrete 3D printing,and thin forming *** criteria include formwork utilization,reinforcement incorporation,geometrical complexity,material enhancement,assembly complexity,surface finish,and build *** demonstrates different multi-criteria decision-making techniques,with both subjective and objective weighting *** given ranking is based on the current condition of digital fabrication in the construction *** study reveals that in the selection of digital fabrication techniques,the criteria including reinforcement incorporation,build area,and geometrical complexity play a pivotal role,collectively accounting for nearly 70% of the overall *** the evaluated techniques,concrete 3D printing emerged as the best performer,however the shotcrete and mesh molding techniques in the second and third positions.

关键词： digital fabrication multicriteria decision-making concrete 3D printing

Seismic response of deep circular tunnels subjected to S-waves:Axial bending

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Underground Space 2024年第4期17卷 267-279页

作者： Chatuphat Savigamin Antonio Bobet Osvaldo p.m.Vitali HR Engineering Services Inc.MedleyFL 33166United States Lyles School of Civil Engineering Purdue UniversityWest LafayetteIN 47907United States Department of Civil Environmentaland Construction EngineeringUniversity of Hawaii at ManoaHonoluluHI 96822United States

Ovaling deformation of circular tunnels has received great interest from the tunneling community because this mode of seismicinduced deformation is considered the most ***,there is growing evidence that other deformation modes can also be important and thus need to be considered in *** study presents a new analytical solution to estimate axial bending(snaking),a mode of deformation caused by S-waves impinging on a tunnel parallel to the tunnel *** solution is developed using the soilstructure interaction approach with the assumption that the interface between the ground and the tunnel lining is frictionless(fullslip).Full dynamic numerical simulations are conducted to verify the new full-slip solution,together with the existing no-slip *** of dynamic amplification are also explored for both full-slip and no-slip interface conditions by changing the wavelength(or frequency)of the seismic input motions.

关键词： Seismic response of tunnels Analytical solutions Soil-structure interaction Axial bending Snaking S-waves

Intertype superconductivity evoked by the interplay of disorder and multiple bands

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Frontiers of physics 2024年第4期19卷 81-89页

作者： p.m.marychev A.A.Shanenko A.V.Vagov HSE University 101000 MoscowRussia Center for Advanced mesoscience and Nanotechnology MIPTDolgoprudny141700Russia

Nonmagnetic impurity scattering is known to shift up the Ginzburg-Landau parameter k of a *** this case,when the system is initially in type I,it can change its magnetic response,crossing the intertype domain with k~1 between the two standard superconductivity types and arriving at type *** the present work we demonstrate that the impact of disorder can be much more profound in the presence of the multiband structure of the charge carrier *** particular,when the band diffusivities differ from each other,the intertype domain tends to expand significantly,including points with k>>1 that belong to deep type-Ⅱ in conventional single-band *** finding sheds light on the nontrivial disorder effect and significantly complements earlier results on the enlargement of the intertype domain in clean multiband superconductors.

关键词： superconductivity disorder intertype superconductivity twoband model

mechanisms behind the environmental sensitivity of carbon fiber reinforced polytetrafluoroethylene(pTFE)

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Friction 2024年第5期12卷 997-1015页

作者： pontus JOHANSSON p.mARKLUND m.BJORLING Y.SHI Division of machine Element LuleåUniversity of TechnologyLuleåSE-97187Sweden

Carbon fiber reinforced polytetrafluoroethylene (CF/pTFE) composites are known for their exceptional tribological performance when sliding against steel or cast iron in inert gas environments. Compared to experiments in humid air, about an order of magnitude lower wear rate and several times lower coefficient of friction have been reported for tests conducted in dry nitrogen and hydrogen. moreover, trace moisture has been shown to affect the friction and wear significantly of this tribosystem, although a possible effect of oxygen cannot be ruled out due to uncertainties regarding the oxygen concentrations. While several studies have pointed out the environmental sensitivity of CF/pTFE, the understanding of the underlying mechanisms are very limited. The objective of this research is to investigate the individual and combined effect of oxygen and moisture on the tribological behavior of CF/pTFE sliding against steel. Additionally, this study aims to elucidate the underlying mechanisms that govern the environmental sensitivity of the system. Climate-controlled three-pin-on-disc experiments were conducted in nitrogen atmospheres at various concentrations of oxygen and moisture. The tribological results clearly demonstrate that both moisture and oxygen contribute to increased friction and wear. However, the adverse effect was much more pronounced for oxygen than moisture. A qualitative method was developed to estimate the tribofilm coverage on the CF/pTFE surface. Results showed strong correlation between high coverage of strongly adhered tribofilm and low wear rate. moreover, a loosely adhered tribofilm was observed on top of the CF/pTFE surface in presence of moisture. FTIR analysis indicated that the loosely adhered tribofilm found in the moisture-enriched environment contained a significant amount of adsorbed water, which may explain the lower coefficient of friction in presence of moisture compared to oxygen. The adsorbed water in the loosely adhered tribofilm coul

关键词： polymer composite tribofilm tribochemistry atmosphere

Drought events influence nutrient canopy exchanges and green leaf partitioning during senescence in a deciduous forest

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Forest Ecosystems 2024年第1期11卷 110-119页

作者： J.Touche C.Calvaruso p.De Donato m.-p.Turpault INRAE BEFF-54000NancyFrance UmR 7359 GeoRessourcesFaculte des Sciences-Campus des Aiguillettes54506Vandoeuvre Les NancyFrance EcoSustain Environmental Engineering OfficeResearch and DevelopmentKanfen57330France

The increase in the frequency and intensity of drought events expected in the coming decades in Western Europe may disturb forest biogeochemical cycles and create nutrient deficiencies in *** possible origin of nutrient deficiency is the disturbance of the partitioning of the green leaf pool during the leaf senescence period between resorption,foliar leaching and senesced ***,the effects of drought events on this partitioning and the consequences for the maintenance of tree nutrition are poorly *** experiment in a beech forest in meuse(France)was conducted to assess the effect of drought events on nutrient canopy exchanges and on the partitioning of the green leaf pool during the leaf senescence *** aim was to identify potential nutritional consequences of droughts for *** nutrient dynamics,including resorption,chemistry of green and senesced leaves,foliar absorption and leaching in mature beech stands from 2012 to 2019 allowed us to compare the nutrient exchanges for three nondry and three dry years(i.e.,with an intense drought event during the growing season).During dry years,we observed a decrease by almost a third of the potassium(K)partitioning to resorption(*** efficiency),thus reducing the K reserve in trees for the next growing *** result suggests that with the increased drought frequency and intensity expected for the coming decades,there will be a risk of potassium deficiency in trees,as already observed in a rainfall exclusion experiment on the same study *** foliar leaching and higher parititioning to the senesced leaves for K and phosphorus(p)were also *** addition,a slight increase in nitrogen(N)resorption efficiency occurred during dry years which is more likely to improve tree *** calcium(Ca)negative resorption decreased,with no apparent consequence in our study *** results show that nutrient exchanges in the canopy and the partitioning of the green leaf

关键词： Natural drought Beech forest Canopy Resorption Foliar leaching Senesced leaves Nutrition

Development of an ultrathin liquid sheet target for laser ion acceleration at high repetition rates in the kilohertz range

在线全文

学校读者我要写书评

暂无评论

High power Laser Science and Engineering 2024年第3期12卷 134-145页

作者： m.Füle A.p.Kovács T.Gilinger m.Karnok p.Gaál S.Figul G.marowsky K.Osvay National Laser-Initiated Transmutation Laboratory University of SzegedSzegedHungary Department of Experimental physics University of SzegedSzegedHungary ELI ALpS ELI-HU Non-Profit Ltd.SzegedHungary Department of Optics and Quantum Electronics University of SzegedSzegedHungary Advanced microfluidic Systems GmbH GöttingenGermany

A colliding microjet liquid sheet target system was developed and tested for pairs of round nozzles of 10,11 and 18μm in *** sheet's position stability was found to be better than a few *** interaction with 50 mJ laser pulses,the 18μm jet has a resonance amplitude of 16μm at a repetition rate of 33 Hz,while towards 100 Hz it converges to 10μm for all nozzles.A white-light interferometric system was developed to measure the liquid sheet thickness in the target chamber both in air and in vacuum,with a measurement range of 182 nm±1μm and an accuracy of±3%.The overall shape and 3D shape of the sheet follow the Hasson±peck model in *** vacuum versus air,the sheet gradually loses 10%of its thickness,so the thinnest sheet achieved was below 200 nm at a vacuum level of 10±4mbar,and remained stable for several hours of operation.

关键词： diagnostics laser ion acceleration nanometric liquid sheet targets vacuum test

Tensile deformation of fine-grained mg at 4K,78K and 298K

在线全文

学校读者我要写书评

暂无评论

Journal of magnesium and Alloys 2024年第6期12卷 2534-2556页

作者： m.Walag A.Kula p.Noga T.Tokarski G.Cios m.Niewczas AGH University of Krakow Faculty of Non-Ferrous MetalsKrakowPoland AGH University of Krakow Academic Centre for Materials and NanotechnologyKrakowPoland materials Science and Engineering McMaster UniversityHamiltonCanada

The impact of grain size, ranging from 0.9 μm to 9 μm, on the mechanical properties of commercially pure mg is investigated at temperatures of 4K, 78K, and 298K. The mechanisms governing plastic flow are influenced by both grain size and temperature. At 4K and 78K, dominant deformation modes in mg involve dislocation glide and extension twinning, regardless of grain size. The interactions between basal and non-basal dislocations and dislocations with grain boundaries promote an unusually high rate of work hardening in the plastic regime, leading to premature failure. The yield stress follows the Hall-petch relationship σy~ k/√d, with the slope k increasing with decreasing temperature. At 298K, in addition to dislocation glide and twinning, grain boundary sliding(GBS) becomes significant in samples with grain sizes below 3 μm, considerably enhancing the material's deformability. GBS activation provides an additional recovery mechanism for dislocations accumulating at grain boundaries, facilitating their absorption during sliding and rotation. Analysis of σ Θ relationship suggests that the basal slip is the dominant dislocation mode in mg at 298K. Decreasing grain size suppresses dislocation activity and twinning and increases GBS, resulting in lower Θ and σ Θ values. Suppressing conventional deformation modes coupled with enhanced GBS yields stress softening, breaking down the Hall-petch relationship in mg below 3 μm grain size, leading to an inverse Hall-petch behaviour. The work reports new data on the strength, ductility, work hardening and fracture behaviour, and their variations with mg grain size across different temperature regimes.

关键词： polycrystalline mg mechanical properties Deformation mechanisms Work-hardening Texture evolution Cryogenic temperatures Hall-petch relationship

Developing a two-decadal time-record of rice field m.ps using Landsat-derived multi-index image collections with a random forest classifier:A Google Earth Engine based approach

在线全文

学校读者我要写书评

暂无评论

Information processing in Agriculture 2024年第2期11卷 260-275页

作者： W.Ashane m.Fernando I.p.Senanayake Department of Nano Science Technology Wayamba University of Sri LankaKuliyapitiya 60200Sri Lanka Dchoolf Engineing CllegeoEngineeringSience and EnionmentThe UniversyewcastleCallaghanW2Austraia

Historic m.ps showing the temporal distribution of rice fields are important for precision agriculture,irrigation optimisation,forecasting crop yields,land use management and formulating ***,m.pping rice felds using traditional ground surveys is impractical when high cost,time and labour requirements are considered,and the availability of such detailed records is *** satellite remote sensing appears to be a viable solution,conventional segmentation and classification methods with spectral bands are often unable to contrast the distinct characteristics between rice fields and other vegetation *** this end,we explored a novel,Google Earth Engine(GEE)based multiindex random forest(RF)classification approach to m.p rice fields over two *** images from 2000 to 2020 of two Sri Lankan rice cultivation districts were extracted from GEE and a multi-index RF classification algorithm was applied to distinguish the rice *** results showed above 80%accuracy for both training and validation,when compared against high spatial resolution Google Earth *** essence,multi-index sampling and RF together synergised the compelling classifcation accuracy by effectively capturing vegetation,water(ponding)and soil characteristics unique to the rice felds using a single-click *** m.ps developed in this study were further compared against the mODIS land cover type product(mCD12Q1)and the corresponding superior statistics on rice fields demonstrated the robustness of the proposed *** work seeking effective index combinations is recommended,and this approach can potentially be extended to other crop analyses elsewhere.

关键词： Google Earth Engine(GEE) Image classification Random forest m.pping rice fields Time series analysis Vegetation index