检索结果-南通市图书馆

Copper slag assisted coke reduction of phosphogypsum for sulphur dioxide preparation

Chinese Journal of Chemical Engineering 2024年第1期65卷 43-53页

作者： dong ma Qinhui Wang State Key Laboratory of Clean Energy Utilization Institute for Thermal Power EngineeringZhejiang UniversityHangzhou 310027China

The reduction of phosphogypsum(PG)to lime slag and SO_(2)using coke can effectively alleviate the environmental problems caused by PG.However,the PG decomposition temperature remains high and the product yield remains poor.By adding additives,the decomposition temperature can be further reduced and PG decomposition rate and product yield can be improved.However,the use of current additives such as Fe_(2)O_(3)and SiO_(2)brings the problem of increasing economic cost.Therefore,it is proposed to use solid waste copper slag(CS)as a new additive to reduce PG to prepare SO2,which can reduce the cost and meet the environmental benefits at the same time.The effects of proportion,temperature and thermostatic time on PG decomposition are investigated by experimental and kinetic analysis combined with FactSage thermodynamic calculations to optimize the roasting conditions.Finally,the reaction mechanism is proposed.It is found that adding CS to the coke and PG system can increase the rate of PG decomposition and SO_(2)yield while lowering the PG decomposition temperature.For example,when the CS/PG mass ratio increases from 0 to 1,PG decomposition rate increases from 83.38%to 99.35%,SO_(2)yield increases from 78.62%to 96.81%,and PG decomposition temperature decreases from 992.4℃to 949.6℃.The optimal reaction parameters are CS/PG mass ratio of 1,Coke/PG mass ratio of 0.06 at 1100℃for 20 min with 99.35%PG decomposition rate and 96.81%SO_(2) yield.The process proceeds according to the following reactions:2CaSO_(4)+ 0.7C + 0.8Fe_(2)SiO_(4)→0.8Ca_(2)SiO_(4)+ 0.2Ca_(2)Fe_(2)O_(5)+ 0.4Fe_(3)O_(4)+2SO_(2)+ 0.7CO_(2)Finally,a process for decomposing PG with coke and CS is proposed.

关键词： Phosphogypsum Sulfur dioxide Copper slag Fluidized-bed Reduction Waste treatment

来源：

维普期刊数据库

同方期刊数据库博看期刊评论

在线全文

学校读者我要写书评

暂无评论

Experimental investigation on weak shock wave mitigation characteristics of flexible polyurethane foam and polyurea

引用

Defence Technology（防务技术） 2024年第1期31卷 179-191页

作者： Shiyu Jia Cheng Wang Wenlong Xu dong ma Fangfang Qi State Key Laboratory of Explosion Science and Technology Beijing Institute of TechnologyBeijing100081China Institute for Advanced Technology Shandong UniversityJinan250061China

In recent years,explosion shock wave has been considered as a signature injury of the current military conflicts.Although strong shock wave is lethal to the human body,weak shock wave can cause many more lasting consequences.To investigate the protection ability and characteristics of flexible materials and structures under weak shock wave loading,the blast wave produced by TNT explosive is loaded on the polyurethane foam with the density of 200.0 kg/m3(F-200)and 400.0 kg/m3(F-400),polyurea with the density of 1100.0 kg/m^(3)(P-1100)and structures composed of the two materials,which are intended for individual protection.Experimental results indicate that the shock wave is attenuated to weak pressure disturbance after interacting with the flexible materials which are not damaged.The shock wave protective capability of single-layer materials is dependent on their thickness,density and microscopic characteristics.The overpressure,maximum pressure rise rate and impulse of transmitted wave decrease exponentially with increase in sample thickness.For the same thickness,F-400 provides better protective capability than F-200 while P-1100 shows the best protective capability among the three materials.In this study,as the materials are not destroyed,F-200 with a thickness more than10.0 mm,F-400 with a thickness more than 4.0 mm,and P-1100 with a thickness more than 1.0 mm can attenuate the overpressure amplitude more than 90.0%.Further,multi-layer flexible composites are designed.Different layer layouts of designed structures and layer thickness of the single-layer materials can affect the protective performance.Within the research range,the structure in which polyurea is placed on the impact side shows the optimal shock wave protective performance,and the thicknesses of polyurea and polyurethane foam are 1.0 mm and 4.0 mm respectively.The overpressure attenuation rate reached maximum value of 93.3%and impulse attenuation capacity of this structure are better than those of single-layer polyurea and polyurethane foam with

关键词： Free-field explosion Weak shock wave mitigation Polyurea Polyurethane foam Multi-layered composites

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Serrated flow behavior of GH536 superalloy under different loading rates at room temperature

引用

Rare Metals 2024年第5期43卷 2317-2323页

作者： Wen-Xiang Gao dong ma Li-Li Zhao Fan Ye Ling Shao Su-Jun Wu School of materials Science and Technology Beihang University

Serrated flow phenomenon has been widely observed among different metals due to the potential influence on their applications.Uniaxial tensile tests of nickel-based superalloy GH536 were carried out at loading rates of 0.06,0.60,3.60,and 36.00 mm·min-1at room temperature,respectively.The tensile stress–strain curves demonstrate repetitive and discontinuous yielding behavior,namely serrated flow.It is observed that the stress–strain curves were dominated by type B serration,and original annealing twin boundaries （TBs） were distorted to various degrees under comparatively different lower tensile rates.In contrast,the TBs almost disappear,and the type B serrations become smoother and regular under the higher loading rates.This phenomenon can be attributed to the interactions between TBs and dislocations during tensile deformation.Coupled effects of the mobile and immobile dislocations illustrate the unsteady amplitude of serrations observed in stress–strain curves.Transmission electron microscope images of tested pieces reveal the interaction of dislocation and TB,with dislocation tangling around the TBs.

关键词： Nickel-based superalloy Serrations Twin boundaries Deformation mechanism

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Microstructure and properties of LZQT600-3 HCCDIBs for plunger pump cylinder

引用

China Foundry 2024年第2期21卷 197-204页

作者： Chun-jie Xu Yuan-ying Jin dong ma Zhen Zhao Jia-wei Qi Shang Sui Xiang-quan Wu Can Guo Zhong-ming Zhang Yong-hui Liu Dan Shechtman School of materials Science and Engineering Xi'an University of TechnologyXi'an 710048China Xi'an Shechtman Nobel Prize New materials Institute Xi'an 710048China Tongchuan Huazhu Precision Technology Co. Ltd.Tongchuan 727100ShaanxiChina Faculty of materials Science and Engineering Technion-Israel Insititue of TechnologyHaifa 3200003Israel

It is important to improve the comprehensive performance of the ductile iron bars(DIBs)for the cylinder block of the extra high pressure hydraulic plunger pump and accelerate the industrial application.In this work,the LZQT600-3 DIBs with the diameter of 145 mm were prepared by the horizontal continuous casting(HCC)process,that is,LZQT600-3 HCCDIBs.The microstructure and room temperature tensile properties of different sections[left-edge(surface layer),left-1/2R(left half of the radius),and the center of the HCCDIBs]were studied.The results show that the spheroidization of LZQT600-3 HCCDIBs matrix from the left-edge,left-1/2R to the center is at nodulizing grade II and above.As the cooling rate gradually decreases from surface to the center of the HCCIBs,the number of spheroidized graphite is gradually reduced,the size is gradually increased,the shape factor is decreased,and the pearlite content and lamellate spacing are increased.Along the horizontal direction of the section,the hardness of the material is distributed symmetrically around the center of the HCCDIBs.In the vertical direction,the hardness distribution in the center of the HCCDIBs is asymmetrical due to the gravity during the solidification process.Therefore,the microstructure in the lower part of the section solidifies relatively quickly.The left-edge has the best tensile mechanical properties,and the ultimate tensile strength,yield tensile strength and elongation are 597.3 MPa,418.5 MPa and 9.6%,respectively.The tensile fracture belongs to the ductile-brittle hybrid fracture.The comprehensive performances of LZQT600-3 HCCDIBs meet the actual application requirements of ultra-high pressure hydraulic plunger pump cylinder.

关键词： horizontal continuous casting(HCC) nodular cast iron ductile iron bars microstructure mechanical properties

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Finite-time Prescribed Performance Time-Varying Formation Control for Second-Order Multi-Agent Systems With Non-Strict Feedback Based on a Neural Network Observer

引用

IEEE/CAA Journal of Automatica Sinica 2024年第4期11卷 1039-1050页

作者： Chi ma Dianbiao dong the School of Mechanical Engineering Northwestern Polytechnical UniversityXi’an 710072China

This paper studies the problem of time-varying formation control with finite-time prescribed performance for nonstrict feedback second-order multi-agent systems with unmeasured states and unknown nonlinearities.To eliminate nonlinearities,neural networks are applied to approximate the inherent dynamics of the system.In addition,due to the limitations of the actual working conditions,each follower agent can only obtain the locally measurable partial state information of the leader agent.To address this problem,a neural network state observer based on the leader state information is designed.Then,a finite-time prescribed performance adaptive output feedback control strategy is proposed by restricting the sliding mode surface to a prescribed region,which ensures that the closed-loop system has practical finite-time stability and that formation errors of the multi-agent systems converge to the prescribed performance bound in finite time.Finally,a numerical simulation is provided to demonstrate the practicality and effectiveness of the developed algorithm.

关键词： Finite-time control multi-agent systems neural network prescribed performance control time-varying formation control

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Fast source mask co-optimization method for high-NA EUV lithography

引用

Opto-Electronic Advances 2024年第4期7卷 44-54页

作者： Ziqi Li Lisong dong Xu ma Yayi Wei EDA Center Institute of Microelectronics of Chinese Academy of SciencesBeijing 100029China Key Laboratory of Photoelectronic Imaging Technology and System of Ministry of Education of China School of Optics and PhotonicsBeijing Institute of TechnologyBeijing 100081China University of Chinese Academy of Sciences Beijing 100049China Guangdong Greater Bay Area Applied Research Institute of Integrated Circuit and Systems Guangzhou 510700China

Extreme ultraviolet(EUV)lithography with high numerical aperture(NA)is a future technology to manufacture the integrated circuit in sub-nanometer dimension.Meanwhile,source mask co-optimization(SMO)is an extensively used approach for advanced lithography process beyond 28 nm technology node.This work proposes a novel SMO method to improve the image fidelity of high-NA EUV lithography system.A fast high-NA EUV lithography imaging model is established first,which includes the effects of mask three-dimensional structure and anamorphic magnification.Then,this paper develops an efficient SMO method that combines the gradient-based mask optimization algorithm and the compressivesensing-based source optimization algorithm.A mask rule check(MRC)process is further proposed to simplify the optimized mask pattern.Results illustrate that the proposed SMO method can significantly reduce the lithography patterning error,and maintain high computational efficiency.

关键词： computational lithography high-NA EUV lithography source-mask co-optimization lithography imaging model

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

On hypersurfaces of H2×H2

引用

Science China mathematics 2024年第2期67卷 339-366页

作者： dong Gao Hui ma Zeke Yao School of Science Beijing University of Civil Engineering and Architecture Department of mathematical Sciences Tsinghua University

In this paper, we study hypersurfaces of H2× H2. We first classify the hypersurfaces with constant principal curvatures and constant product angle functions. Then we classify homogeneous hypersurfaces and isoparametric hypersurfaces, respectively. Finally, we classify the hypersurfaces with at most two distinct constant principal curvatures, as well as those with three distinct constant principal curvatures under some additional conditions.

关键词： constant principal curvature homogeneous hypersurface isoparametric hypersurface 53C42 53B25 53C40

来源：

同方期刊数据库评论

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

New Rural Community Construction or Retention Development:A Comparative Analysis of Rural Settlement Transition Mechanism in Plain Agriculture Area of China Based on Actor Network Theory

引用

Chinese Geographical Science 2024年第3期34卷 436-452页

作者： QU Yanbo dong Xiaozhen ma Wenqiu ZHAO Weiying School of Public Administration and Policy Shandong University of Finance and EconomicsJinan 250014China Institute of Land Science and Policy Shandong University of Finance and EconomicsJinan 250014China College of Engineering China Agricultural UniversityBeijing 100083China

It is an important way to realize rural revitalization and sustainable development to guide rural settlement transition(RST)in an appropriate way.This paper uses actor network theory(ANT)to construct a theoretical framework for the study of RST.Taking two typical villages with different transition paths in rural areas of North China Plain as examples,this paper reveals the mechanism of RST and makes a comparative analysis.The results show that:1)after identifying problems and obligatory passage point,key actors recruit heterogeneous actors into the actor network by entrusting them with common interests,and realize RST under the system operation.2)Rural settlements under different transition paths have similarities in the problems to be solved,collective actions and policy factors,but there are differences in the transition process,mechanism and effect.The actor network and mechanism of RST through the path of new rural community construction are more complex and the transition effect is more thorough.In contrast,the degree of RST of retention development path is limited if there is no resource and location advantage.3)Based on the applicable conditions of different paths,this paper designs a logical framework of‘Situation-Structure-Behavior-Result’to scientifically guide the identification of RST paths under the background of rural revitalization.

关键词： rural settlement transition(RST) actor network theory(ANT) transition path transition mechanism plain area China

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Diagnostic performance of dynamic contrast-enhanced magnetic resonance imaging parameters and serum tumor markers in rectal carcinoma prognosis

引用

World Journal of Gastrointestinal Oncology 2024年第5期16卷 1796-1807页

作者： Ren-Qi Mu Jun-Wei Lv Cai-Yun ma Xiao-Hui ma dong Xing Hou-Sheng ma Department of Radiology Yantai Mountain HospitalYantai 264001Shandong ProvinceChina Department of Radiology Yantai Yuhuangding HospitalYantai 264000Shandong ProvinceChina Department of Gynaecology Yantai Yuhuangding HospitalYantai 264000Shandong ProvinceChina The First Clinical Medical College Xinjiang Medical UniversityUrumqi 830011Xinjiang Uygur Autonomous RegionChina

BACKGROUND Rectal carcinoma(RC),one of the most common malignancies globally,presents an increasing incidence and mortality year by year,especially among young people,which seriously affects the prognosis and quality of life of patients.At present,dynamic contrast-enhanced magnetic resonance imaging(DCE-MRI)parameters and serum carbohydrate antigen 19-9(CA19-9)and CA125 Levels have been used in clinical practice to evaluate the T stage and differentiation of RC.However,the accuracy of these evaluation modalities still needs further research.This study explores the application and value of these methods in evaluating the T stage and differentiation degree of RC.AIM To analyze the diagnostic performance of DCE-MRI parameters combined with serum tumor markers(TMs)in assessing pathological processes and prognosis of RC patients.METHODS A retrospective analysis was performed on 104 RC patients treated at Yantai Yuhuangding Hospital from may 2018 to January 2022.Patients were categorized into stages T1,T2,T3,and T4,depending on their T stage and differentiation degree.In addition,they were assigned to low(L group)and moderate-high differentiation(M+H group)groups based on their differentiation degree.The levels of DCE-MRI parameters and serum CA19-9 and CA125 in different groups of patients were compared.In addition,the value of DCE-MRI parameters[volume transfer constant(Ktrans),rate constant(Kep),and extravascular extracellular volume fraction(Ve)in assessing the differentiation and T staging of RC patients was discussed.Furthermore,the usefulness of DCE-MRI parameters combined with serum CA19-9 and CA125 Levels in the evaluation of RC differentiation and T staging was analyzed.RESULTS Ktrans,Ve,CA19-9 and CA125 were higher in the high-stage group and L group than in the low-stage group and M+H Group,respectively(P<0.05).The areas under the curve(AUCs)of the Ktran and Ve parameters were 0.638 and 0.694 in the diagnosis of high and low stages,respectively,and 0.672 and 0.725 in diagnosing moderate-high and low differe

关键词： Rectal carcinoma Volume transfer constant Rate constant Extravascular extracellular volume fraction Serum carbohydrate antigen 19-9 Serum carbohydrate antigen 125

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Flag Varieties of Type B/C and Twisted Yangian

引用

Algebra Colloquium 2024年第1期31卷 129-148页

作者： Zhijie dong Haitao ma Institute for Advanced Study in mathematics of HIT Harbin Institute of Technology Harbin 150001China College of mathematical Science Harbin Engineering University Harbin 150001China

We study the convolution algebra H_(*)^(G×C^(*))(Z)of G×C^(*)-equivariant homology group on the Steinberg variety of type B/C and define an algebra Y that maps to H_(*)^(G×C^(*))(Z).We also study the G-equivariant ... 详细信息

关键词： Yangian fag variety convolution algebra

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：